LevelOne FBR-1161 User Manual
  1. Manuals
  2. Brands
  3. LevelOne Manuals
  4. Modem
  5. FBR-1161
  6. User manual
LevelOne FBR-1161 User Manual

LevelOne FBR-1161 User Manual

Adsl2+ modem router 1wan 1lan 1usb
Hide thumbs Also See for FBR-1161:
Table of Contents

Advertisement

Quick Links

Download this manual
FBR-1161
ADSL2+ Modem Router
1WAN 1LAN 1USB
User Manual
Ver. 1.00-0606

Advertisement

Table of Contents
loading

Related Manuals for LevelOne FBR-1161

Summary of Contents for LevelOne FBR-1161

  • Page 1 FBR-1161 ADSL2+ Modem Router 1WAN 1LAN 1USB User Manual Ver. 1.00-0606...

  • Page 2: Table Of Contents

    Table of Content INTRODUCTION............................1 1.1............................1 VERVIEW 1.2............................3 EATURES INSTALLATION ............................6 2.1..........................6 MPORTANT 2.2........................... 6 ACKAGE ONTENTS 2.3............................7 RONT ANEL 2.4............................8 ANEL 2.5............................. 9 ABLING BASIC INSTALLATION .......................... 10 3.1.
  • Page 3 4.4.2. IP Filter ............................42 4.4.3. SNMP............................44 4.4.4. UPnP............................45 4.4.5. DDNS ............................46 4.5........................... 47 AINTENANCE 4.5.1. Administrator..........................47 4.5.2. Time Zone ..........................48 4.5.3. Firmware ............................ 49 4.5.4. SysRestart..........................50 4.5.5. Diagnostics..........................50 4.6............................. 51 TATUS 4.6.1.

  • Page 4: Introduction

    1. Introduction 1.1. Overview Welcome to the LevelOne FBR-1161. Your router is an “all-in-one” unit, combining an ADSL modem, ADSL router and Ethernet network switch, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection.
  • Page 5 machines as a DHCP client to accept a dynamically assigned IP address from DHCP server and reboot. Each time local machine is powered up; the router will recognize it and assign an IP address to instantly connect it to the LAN. For advanced users, Virtual Service function allows the product to provide limited visibility to local machines with specific services for outside users.

  • Page 6: Features

    1.2. Features ADSL Multi-Mode Standard supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It also supports rate management that allows ADSL subscribers to select an Internet access speed suiting their needs and budgets. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2;...
  • Page 7 www.yahoo.com) and IP address. When a local machine sets its DNS server with this router’s IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS in the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname.
  • Page 8 Supports web based GUI for configuration and management. It is user-friendly and comes with on-line help. It also supports remote management capability for remote users to configure and manage this product. Firmware Upgradeable Device can be upgraded to the latest firmware through the WEB based GUI.

  • Page 9: Installation

    Do not use the same power source for the FBR-1161 as other equipment. Do not open or repair the case yourself. If the FBR-1161 is too hot, turn off the power immediately and have it repaired at a qualified service center.

  • Page 10: Front Panel

    2.3. Front Panel Description Lit steady when there is a PPPoA / PPPoE connection. Lit when successfully connected to an ADSL DSLAM (“linesync”) ADSL Lit when the USB port is connected to the PC and working properly Lit when connected to an Ethernet device. Green for 100Mbps;...

  • Page 11: Rear Panel

    2.4. Rear Panel ADSL RESET Power Switch Port Description Power ON/OFF switch Switch Connect the supplied power adapter to this jack. POWER After the device is powered on, press it to reset the device or restore to factory default settings. 0-3 seconds: reset the device RESET 6 seconds above: restore to factory default settings (this is used when...

  • Page 12: Cabling

    2.5. Cabling Through USB Port The product can be used as a Network Adapter on your PC. That means you do not have to install a network adapter first on your PC before connecting the ADSL Modem/Router. Just connect the supplied USB cable to the USB port of the ADSL2+ Modem/Router and connect the other end to the PC.

  • Page 13: Basic Installation

    3. Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows 98SE/Me/NT/2000/XP, etc. The product provides a very easy and user-friendly interface for configuration. 3.1.

  • Page 14: Installing The Usb Driver

    3.3. Installing the USB Driver If you connect the device through USB port instead of Ethernet port, for the first time the USB cable is connected to the PC, Windows will automatically detect the device. Follow the steps to install the USB driver. 3.3.1.
  • Page 15 Then follow screen. To click the type of setup you prefer, then click Next >. To setup enough information of coping the program files then click Next >.
  • Page 16 Please plug USB cable into ADSL USB Modem. Then, click “Finish”.

  • Page 17: For Windows 98Se & Me

    3.3.2. For Windows 98SE & Me Start Windows. Then insert the installation CD into the CD-ROM drive. In next window, to specify the CD ROM driver directory and to continue. To choose the setup language. ”and click “Next >”. (There are three languages that user can choose: English.
  • Page 18 To click the type of setup you prefer, then click Next >. To setup enough information of coping the program files. Select “Want to restart my computer now” and click OK> Then, click “Finish”.

  • Page 19: Configuring Your Pc Network Properties

    3.4. Configuring Your PC Network Properties 3.4.1. Windows XP Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections Double-click Local Area Connection. In the Local Area Connection Status window, click Properties. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 20: Windows 2000

    3.4.2. Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 21: Windows 98Se/Me

    3.4.3. Windows 98SE/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.Select the Obtain an IP address automatically radio button.

  • Page 22: Configuring Pc In Windows Nt4.0

    3.4.4. Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.Select TCP/IP Protocol and click Properties. 3.Select the Obtain an IP address from a DHCP server radio button and click OK.

  • Page 23: Lan And Wan Port Addresses

    3.5. LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to Subnet Mask 255.255.255.0 automatically get the DHCP server function Enabled...

  • Page 24: Configuring With Your Web Browser

    3.7. Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin”. Congratulation! You are now successfully logon to the ADSL2+ Modem/Router!

  • Page 25: Configuration

    Maintenance (Administration, Time Zone, Firmware, SysRestart, Diagnositics) Status Please see the relevant sections of this manual for detailed instructions on how to configure your LevelOne router. 4.1. Quick Start Click the RUN WIZARD to start configuring The information you need for the Quick Start to get you online are your login (often in the form of username@ispname), your password, and the encapsulation type.
  • Page 26 Quick Start Wizard Step1. Set your new password. Step2: Choose your time zone...
  • Page 27 Step3: Set your Internet connection Step4: Restart your ADSL Router...

  • Page 28: Interface Setup

    4.2. Interface Setup Click to access the following sub-items that configure the ADSL router: Internet, LAN 4.2.1. Internet...
  • Page 29 ATM VC Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. VPI:The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. This field may already be configured. VCI: The valid range for the VCI is 32 to 65535. Enter the VCI assigned to you. This field may already be configured.
  • Page 30 Dynamic IP Address Encapsulation: 1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP LLC(IPoA), 1483 Routed IP VC-Mux, check your ISP for proper connection type. NAT (Network Address Translation): Select Enable or Disable from the drop-sown list box. Refer to the NAT chapter for more details. Default Route: Select Yes or NO to set route rule.
  • Page 31 Static IP Address Encapsulation: 1483 Bridged IP LLC, 1483 Bridged IP VC-Mux, 1483 Routed IP LLC(IPoA), 1483 Routed IP VC-Mux, check your ISP for proper connection type. Static IP Address: Enter the IP address of ADSL Router in dotted decimal notation, it’s assigned by your ISP.
  • Page 32 PPPoE/PPPoA User Name: Enter the user name exactly as your ISP assigned. Password: Enter the password associated with the user name above. Encapsulation: select Bridge in the Mode field, select either PPPoE LLC, PPPoE VC-Mux, PPPoA LLC and PPPoA VC-Mux, check your ISP for proper connection type. Bridge Interface: Activated acts as modem, or Deactivated as modem router.
  • Page 33 Static IP Address: Enter the IP address of ADSL Router in dotted decimal notation, it’s assigned by your ISP. IP Subnet Mask: The default is 255.0.0.0. User can change it to other such as 255.255.255.0.Type the subnet mask assigned to you by your ISP (if given). Gateway: You must specify a gateway IP address (supplied by your ISP) when you use 1483 Bridged IP in the Encapsulation field in the previous screen.

  • Page 34: Lan

    4.2.2. LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building. Router Local IP IP Address: Enter the IP address of ADSL Router in dotted decimal notation, for example, 192.168.1.254 (factory default).
  • Page 35 DHCP DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a server. DHCP: If set to Disabled, the DHCP server will be disabled. If set to Enable, your ADSL Modem Series can assign IP addresses, an IP default gateway and DNS servers to Windows OS and other systems that support the DHCP client.

  • Page 36: Advanced Setup

    4.3. Advanced Setup 4.3.1. Firewall Enable the firewall function, it provides Syn Flooding Attack, Ping of Death, Teardrop, Land Attack and Port Scanning protections 4.3.2. Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the gateway to Internet.
  • Page 37 ADD Route Destination IP Address This is the destination subnet IP address. IP Subnet Mask It is the destination IP addresses based on above destination subnet IP Gateway IP Address This is the gateway IP address to which packets are to be forwarded.

  • Page 38: Nat

    4.3.3. NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dynamic NAPT. It provides dynamic Network Address Translation capability between LAN and multiple WAN connections, and the LAN traffic is routed to appropriate WAN connections based on the destination IP addresses and Route Table.
  • Page 39 The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by the Firewall and NAT algorithms then passed to the DMZ host, when a packet received does not use a port number used by any other Virtual Server entries.
  • Page 40 by and point to your router, which then needs to deliver all traffic to the private IP addresses used by your PCs. Please see the WAN configuration section of this manual for more information on NAT. The device can be configured as a virtual server so that remote users accessing services such as Web or FTP services via the public (WAN) IP address can be automatically redirected to local servers in the LAN network.
  • Page 41 IP Address Mapping Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numbers do not change for the One-to-one NAT mapping type. Many-to-One: This is the mode maps multiple local IP addresses to one global IP address.
  • Page 42 Local End IP: This is the end Inside Local IP Address (ILA). If your rule is for all local IP addresses, then enter 0.0.0.0 as the Local Start IP address and 255.255.255.255 as the Local End IP address. This field is N/A for One-to-one and Server mapping types. Public Start IP: This is the starting Inside Public IP Address.

  • Page 43: Adsl

    4.3.4. ADSL ADSL Mode: The default setting is Auto Sync-UP. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.dmt, G.lite, and T1.413. But in some area, multimode cannot detect the ADSL line code well. If it is the case, please adjust the ADSL line code to G.dmt or T1.413 first.

  • Page 44: Access Management

    4.4. Access Management 4.4.1. ACL Access Control Listing allows you to determine which services/protocols can access which ADSL Modem Series interface from which computers. ACL: Activated to enable ACL function ACL Rule Index: Select index from the drop down list box to create ACL rule. Active: Select Yes to enable this ACL rule.

  • Page 45: Ip Filter

    4.4.2. IP Filter You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that want to access the ADSL Router. The default IP 0.0.0.0 allows any client to use this service to remotely manage the ADSL Router. IP Filter Set Editing IP filter Set Index: This is item number Interface: Select which channel (PVC) to configure.
  • Page 46 IP Filter Rule Editing IP Filter Rule Index: This is item number Active: Select Yes from the drop down list box to enable IP filter rule. Source IP Address: The source IP address or range of packets to be monitored. Subnet Mask: It is the destination IP addresses based on above destination subnet IP Port Number: This Port or Port Ranges defines the port allowed to be used by...

  • Page 47: Snmp

    4.4.3. SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. ADSL Modem series supports SNMP agent functionality which allows a manager station to manage and monitor the router through the network. Get Community: Type the Get Community, which is the password for the incoming Get-and GetNext requests from the management station.

  • Page 48: Upnp

    4.4.4. UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device.

  • Page 49: Ddns

    4.4.5. DDNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time.

  • Page 50: Maintenance

    4.5. Maintenance 4.5.1. Administrator In factory setting, the default password is admin, and that for user is also password. You can change the default password to ensure that someone cannot adjust your settings without your permission. Every time you change your password, please record the password and keep it at a safe place.

  • Page 51: Time Zone

    4.5.2. Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone. After a successful connection to the Internet, the router will retrieve the correct local time from the SNTP server you have specified.

  • Page 52: Firmware

    4.5.3. Firmware Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and modified, and your router allows you to upgrade the software it runs to take advantage of these changes.

  • Page 53: Sysrestart

    4.5.4. SysRestart Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.

  • Page 54: Status

    4.6. Status 4.6.1. Device Info Device Information Firmware version: This is the Firmware version MAC Address: This is the MAC Address IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. DHCP Server: LAN port DHCP role - Enabled, Relay or disabled...
  • Page 55 Virtual Circuit: There are eight groups of PVC can be defined. Status: “Not connected” or “Connected” Connection Type: Name of the WAN connection. IP Address: WAN port IP address. Subnet mask: WAN port IP subnet mask. Default Gateway: The IP address of the default gateway. DNS Server: WAN port DHCP role - Enabled, Relay or disabled ADSL ADSL firmware Ver: This is the DSL firmware version associated with your router...

  • Page 56: System Log

    4.6.2. System Log Display system logs accumulated up to the present time. You can trace historical information with this function.

  • Page 57: Statistics

    4.6.3. Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and "Receive Statistics". Ethernet Interface: This field displays the type of port Transmit Frames: This field displays the number of frames transmitted in the last second. Transmit Multicast Frames: This field displays the number of multicast frames transmitted in the last second.
  • Page 58 ADSL Transmit total PDUs: This field displays the number of total PDU transmitted in the last second. Transmit total Error Counts: This field displays the number of total error transmitted in the last second. Receive total PDUs: This field displays the number of total PDU received in the last second. Receive total Error Counts: This field displays the number of total error received in the last second.

  • Page 59: Troubleshooting

    5. Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider. This could save your time and effort but if the symptoms persist, then consult your service provider. Problems starting up the router Problem Corrective Action...
  • Page 60 Problems with the LAN Interface Problem Corrective Action Can’t ping any PCs on Check the Ethernet LEDs on the front panel. The LED should the LAN. be on for a port that has a PC connected. If it is off, check the cables between your router and the PC.

Table of Contents