Advertisement
Quick Links
E E E E
C C C C H H H H
Watermakers
1000-BHL- 2 / 1300-BHL- 3 / 1800-BHL- 4
PAGE
2
INTRODUCTION
3
SPECIFICATIONS
4
STANDARD SYSTEM FEATURES
5-6
INSTALLATION INSTRUCTIONS
7-8
OPERATION INSTRUCTIONS
9
MEMBRANE CLEANING PROCEDURE
10
MAINTENANCE TIMETABLE
11
PRESSURE VESSEL ENDPLUG CHANGING PROCEDURE
12
ELECTRICAL DIAGRAM
13
TROUBLESHOOTING GUIDE
14-15
HIGH PRESSURE PUMP REPAIR INSTRUCTIONS
16-17
LIMITED WARRANTY
2 2 2 2
BEACH HOUSE SERIES
(VERTICAL SYSTEM)
OWNERS MANUAL
O Tec.
O Tec.
O Tec.
O Tec.
TM
Advertisement
Related Manuals for ECH2O Tec. 1000-BHL- 2
Summary of Contents for ECH2O Tec. 1000-BHL- 2
- Page 1 O Tec. O Tec. O Tec. O Tec. 2 2 2 2 Watermakers BEACH HOUSE SERIES (VERTICAL SYSTEM) 1000-BHL- 2 / 1300-BHL- 3 / 1800-BHL- 4 OWNERS MANUAL PAGE INTRODUCTION SPECIFICATIONS STANDARD SYSTEM FEATURES INSTALLATION INSTRUCTIONS OPERATION INSTRUCTIONS MEMBRANE CLEANING PROCEDURE...
- Page 2 Thank you for choosing an ECHO Tec. reverse osmosis desalination system. We trust that you will be completely satisfied with our product. The Beach House Series has been specially designed for small hotels, marinas and beach houses. The high power efficiency and low maintenance cost makes high quality RO water in many cases more economical than land supplied water, if available.
-
Page 3: Specifications
SPECIFICATIONS RATED PERFORMANCE: ECHO Tec: 1000 – BHL – 2 1300 – BHL – 3 1800 – BHL – 4 ° ° RO MEMBRANE TYPE: SALT REJECTION: SALINITY RANGE: PH RANGE: CHLORINE TOLERANCE: OPERATING PRESSURE: FEED WATER PRESSURE: FEED WATER TEMPERATURE RANGE: °... - Page 4 STANDARD SYSTEM FEATURES Aluminum vertical frame Pressure vessel(s) with reverse osmosis membrane(s) Instruments Pressure Gauges: Flow Meter: Conductivity: 1 Hardener / pH neutralizer kit...
-
Page 9: Membrane Cleaning Procedure
MEMBRANE CLEANING PROCEDURE CAUTION: The use of chemicals or cleaning methods other than those outlined in the cleaning instructions will void the ECHO Tec. warranty. Nonionic surfactants for membrane cleaning or other chemicals not approved in writing by Echo Marine Ltd. -
Page 10: Maintenance Timetable
MAINTENANCE TIMETABLE COMPONENT MAINTENANCE TIME INTERVAL REQUIRED INTERMITTENT DUTY CAUTION: ADHERE TO THE SAFETY ADVISES OF THE CLEANING AGENTS... - Page 11 MEMBRANE CHANGING PROCEDURE PRESSURE VESSEL END PLUG CHANGING PROCEDURE It is important not to over tighten the product port/s to avoid the end plug to crack.
-
Page 13: Troubleshooting Guide
HIGH PRESSURE PUMP SYSTEM TROUBLESHOOTING GUIDE MALFUNCTION CAUSE REMEDY The pressure Broken valve spring Replace spring drops Fouled inlet strainer Clean strainer Fouled pre-filter(s) Replace filter cartridge(s) Cavitation (Noisy operation) Check suction lines for restrictions Air in system Check suction lines for leaks Water in crankcase High humidity Reduce oil change interval... - Page 14 HIGH PRESSURE PUMP REPAIR INSTRUCTION ECHO TEC PUMP SERIES XL-60/2.3, XL-60/3.0 AND XL-60/3.6 ∂ ssembly isAssembly 1.1 - Unscrew head bolts. ∂ Tightening sequence of head bolts, for XT Series and HPE Series, for XR Series and XL Series. 1.2 - Remove the head by rotating the shaft and levering between head and body. 1.3 - For re-assembly: Invert above instructions, and keep to torque rates shown on page 8. nsPecTiOn inleT OuTleT vAlves 2.1 - Remove valve caps, slide out inlet/outlet valves check the sondition of the various components of the...
- Page 15 3.2 - Disassemble the components of the piston guide, checking the condition, replace if necessary. 3.3 - For re-assembly: Invert operation. ePlAcing The PisTOns 4.1 - Remove the head (See ∂), then unscrew the piston retainers. 4.2 - Slide off the ceramic pstions, check their condition, and replace if necessary. 4.3 - For re-asembly: Invert above operations. Keep to torque rating and shown on page 8. Be careful not to ePlAcing Oil seAls scratch piston guide! 6.1 - Remove the head (See ∂), • remove the ceramic pistons • discharge oil 6.2 - Remove the oil seals and the O-Rings, checking the seats and the piston guides. 6.3 - Remove the rear cover gasket. 6.4 - For re-assembly: Invert above operations. Keep to torque ratings as shown on page 8. RAnk mechAism mAinTenAnce 7.1 - Remove the head (See ∂), • remove the ceramic pistons • discharge oil 7.2 - Remove the rear cover. 7.3 - Remove the con-rod sliding the one piece-rod whilst removing the shaft. 7.4 - For re-assembly: Invert above operations. Replace the oil seals!