Advertisement
Advertisement
Table of Contents
Related Manuals for INVISIBLE FENCE ICT 725
Summary of Contents for INVISIBLE FENCE ICT 725
- Page 1 ICT 725 Transmitter Operation and Installation Manual Made in the USA...
-
Page 2: How To Install
4. Servicing: Other than repairing the signal loop 7. The 12v AC transformer is plugged into the trans- wire, do not attempt to service any Invisible Fence equip- mitter and is connected to a 110v AC outlet. ment yourself. Refer all service to an authorized Invisible Fence professional only. - Page 3 150 feet of twisted pair. 12v battery. With a charged 12v battery the ICT 725 The ICT 725 has a green LED to indicate that will power the loop if AC electric power is lost.
-
Page 4: Installing The Signal Loop
ICT 725 Transmitter Installation continued To replace the cover on the ICT 725, line up with up to 150 feet of twisted pair. There is no haz- the two tabs on top of the cover plate with the two ard in touching or exposing the wire because the insert slots, located on the top of the base, and insert wire carries only low voltage electricity. -
Page 5: Grounding The System
Connecting the Grounding Wire to the ICT 725 Circuit Board Put the grounding wire pin into the square screw clamp marked EARTH on the transmitter circuit board. Be careful not to push the pin too far through the connector. -
Page 6: Setting The Signal Field
7k setting is down. in the grounding wire. There are two signal field adjustment knobs on the ICT 725 circuit board. The right knob is the An LP Card helps protect the transmitter from course signal field adjustment, and is numbered 1 lightning and surge damage. -
Page 7: Installing A Battery Backup
Drill 4 small pilot holes in the wall where the screws will go. A 12v battery connected to an ICT 725 will 2. Lace a 12” wire tie around the inside of the power the signal field loop in the event of a power battery box running the tie all the way around the outage. - Page 8 4. Put the battery in the box and secure it by and BLACK wires running from pulling the wire tie tight around it. ICT 725 transmitter to the battery. 5. Align the battery box with the battery over the pilot holes in the wall taking care that the wires Detecting Low Voltage in the 12v Battery from the battery are in one of the exit notches.
-
Page 9: Caution And Care
“Invisible Fence Safe Dog Training Manual”. 2. The Computer Collar is worn snugly on the that stated in this manual. Invisible Fence sys- neck under the lower jaw. tems are designed for animal use only. 3. The Computer Collar is... - Page 10 To install a new Power Cap, line up the lugs on the pet’s neck. Each Invisible Fence ® profes- on the cap with the grooves in the opening of the sional should recommend a schedule for changing cap chamber.
- Page 11 WARNING: The use of any battery other than a battery authorized by IFCO Enterprises, Inc., can cause a Computer Collar to operate erratically. The use of an unauthorized battery in an ® Invisible Fence Computer Collar will void the manufacturer’s warranty on the collar.
-
Page 12: Wire Specifications
“Service Diagnostic Questions” above to try to determine what the problem may be. If, ® for any reason, your Invisible Fence system still does not operate as described in this manual or if you encounter any difficulty training your pet, call your... -
Page 13: Important Warnings
Customer should immediately stop using the system, unplug the transmitter, and contact ® your local Invisible Fence Dealer or IFCO Enterprises, Inc. Reported incidents have typically involved: 1) dogs with pre-existing aggressive tendencies;... - Page 14 Only, Original, Pet Safety System are registered trademarks of IFCO Enterprises, Inc. IFCO, Pro Dog, Invisible Fencing Dogs’ Life, Your Dog Safe @ Home, Invisible Gate, and Invisible Sentry are trademarks of IFCO Enterprises, Inc. Invisible Fence Brand products are covered by various patents, both domestic and foreign.
Need help?
Do you have a question about the ICT 725 and is the answer not in the manual?
Questions and answers