Table of Contents
Advertisement
Other Settings
Chapter 10:
Other Settings
The Input Setup menu
You only need to make settings in the Input Setup menu
if you didn't hook up your digital equipment according to
the default settings (see Input function default and
possible settings on page 66). In this case, you need to
tell the receiver what equipment is hooked up to which
terminal so the buttons on the remote correspond to the
components you've connected.
PARAMETER
EXIT
RECEIVER
RECEIVER
SOURCE
TOP MENU
DVD
BD
TV
HDMI
ST
PTY
DVR 1
DVR 2
CD
CD-R
SEARCH
SETUP
SETUP
FM/AM
iPod USB
iPod CTRL
1
Switch on the receiver and your TV.
Use the RECEIVER button to switch on.
2
Press RECEIVER on the remote control, then press
SETUP.
An on-screen display (OSD) appears on your TV. Use /
// and ENTER to navigate through the screens
and select menu items. Press RETURN to confirm and
exit the current menu.
3
Select 'Input Setup' from the System Setup menu.
System Setup MENU
1 . Auto MCACC
2 . Surround Back System
3 . Manual MCACC
4 . Data Management
5 . Manual SP Setup
6 . Input Setup
7 . Other Setup
:Exit
4
Select the input function that you want to set up.
The default names correspond with the names next to the
terminals on the rear panel (such as DVD or VIDEO)
which, in turn, correspond with the names on the remote
control.
6.Input Setup
(1/2)
I n p u t
DV D
D i g i t a l I n
[ C OA X - 1 ]
H D M I I n p u t
[
O N
]
C o m p o n e n t I n [ C o m p - 3 ]
(
NEXT )
:Finish
Note
1 For high-definition video (using component video connections), or when digital video conversion is switched off (in Setting the Video options on page 70),
you must connect your TV to this receiver using the same type of video cable as you used to connect your video component.
2 You will have to make an SR+ cable connection from a CONTROL OUT jack on the display to the CONTROL IN jack on this receiver (opposite from the
setup in Using this receiver with a Pioneer flat screen TV on page 60). Note that to control this receiver using the remote, you will have to point it at the flat
screen TV's remote sensor after making this connection.
PARAMETER
TUNE
TOOLS
AUDIO
DISPLAY
CH
MENU
T.EDIT
TV CTRL
RECEIVER
RECEIVER
ENTER
ENTER
ENTER
ST
RETURN
RETURN
MAIN
ZONE 2
TUNE
6.Input Setup
(1/2)
I n p u t
DV D
D i g i t a l I n
[ C OA X - 1 ]
H D M I I n p u t
[
O N
]
C o m p o n e n t I n [ C o m p - 3 ]
(
NEXT )
:Finish
6.Input Setup
(1/2)
(
Back )
DVD
I n p u t N a m e
R e n a m e
1 2 V Tr i gg e r 1
[
O F F
]
1 2 V Tr i gg e r 2
[
O F F
]
P D P I n ( S R + ) [
O F F
]
ENTER:Next
:Finish
5
Select the input(s) to which you've connected your
component.
For example, if your DVD player only has an optical
output, you will need to change the DVD input function's
Digital In setting from COAX-1 (default) to the optical
input you've connected it to. The numbering (OPT-1 to 3)
corresponds with the numbers beside the inputs on the
back of the receiver.
• If you change the setting to an input that has been
previously assigned to another function (for example,
TV SAT), the setting for that function will
automatically be switched off.
• If your component is connected via a component
video cable to an input terminal other than the
default, you must tell the receiver which input
terminal your component is connected to, or else you
may see the S-Video or composite video signals
instead of the component video signals.
6
When you're finished, select 'Next' to continue to
the next screen.
The second screen of the Input Setup has three optional
settings:
• Input Name – You can choose to rename the input
function for easier identification. Select Rename to
do so, or Default to return to the system default.
• 12V Trigger 1 / 2 – After connecting a component to
one of the 12 volt triggers (see Switching components
on and off using the 12 volt trigger on page 60), select
MAIN, ZONE 2 or OFF for the corresponding trigger
setting to switch it on automatically along with the
(main or sub) zone specified.
• PDP In (SR+) – To control certain functions on this
receiver from a flat screen TV, select the display input
to which you've connected the receiver.
7
When you're finished, press RETURN.
You will return to the System Setup menu.
10
1
2
65
En
Advertisement
Table of Contents
