Subscribe to Our Youtube Channel
Related Manuals for Ozito AWG-964
Summary of Contents for Ozito AWG-964
- Page 1 Arc Welder 140 Amp Fan Cooled Operation Manual 3 Year Replacement Warranty AWG-964 CAUTION: Read this operation manual before using this tool. 1010 www.ozito.com.au To view the full range visit:...
-
Page 2: Specifications
SPECIFICATIONS - MODEL NO. AWG-964 Input Power: 240V - 50Hz Max. No Load Voltage: Current Range: 55 - 130 Amp Peak Current: 140 Amp Duty Cycle: 25% @ 80 Amp Electrode Size: 2 - 3.2mm KNOW YOUR PRODUCT 1. Carry Handle 6. -
Page 3: Table Of Contents
TABLE OF CONTENTS SPECIFICATIONS……………………………………….. Page 1 TABLE OF CONTENTS………………………………… Page 2 INTRODUCTION………………………………………… Page 3 SAFETY INSTRUCTIONS………………………………. Page 3 GENERAL SAFETY RULES…………………………….. Page 4 OPERATION…………………………………………….. Page 7 MAINTENANCE………………………………………… Page 11 DESCRIPTION OF SYMBOLS………………………… Page 11 CONTENTS……………………………………………… Page 12 WARRANTY……………………………………………… Page 13... -
Page 4: Introduction
This electrical equipment has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito products are interchangeable for Australia and New Zealand. -
Page 5: General Safety Rules
GENERAL SAFETY RULES 1. Keep work areas clean. Cluttered work areas and benches can cause accidents. 2. Consider work area environment. Do not expose your equipment to high humidity or rain. Do not use your equipment in damp or wet conditions. Keep the work area well lit. - Page 6 GENERAL SAFETY RULES (cont.) 14. Store equipment. When not in use, equipment should be stored in a dry, locked up or high place, out of reach of children. 15. Maintain mains equipment with care. Keep the equipment clean and in good condition for better and safer performance.
- Page 7 SAFETY INSTRUCTIONS FOR WELDERS (cont.) Disconnect from the power supply before replacing electrodes. Avoid direct contact with the welding circuit. Do not use the welder to defrost piping. Ensure the welder is placed on a level surface to prevent overturning. Provide adequate ventilation or a means for removal of the welding fumes produced (forced circulation using a blower or fan).
-
Page 8: Operation
OPERATION Remove the welder and contents from the carton. Place the welder in an open area where the vents of the housing are not obstructed. Earth Clamp Prior to connecting the earth clamp (6) it may be necessary to clean the surface of the work piece using the metal brush. - Page 9 OPERATION (cont.) ARC WELDERS DO NOT OPERATE CONTINOUSLY FOR EXTENDED PERIODS WITHOUT BEING ALLOWED TO COOL. DO NOT TURN YOUR WELDER OFF AS THE FAN WILL ASSIST IN REDUCING THE COOLING TIME. All Welders have a feature called a duty cycle. Duty cycle on a welder refers to the time in which the welder operates during normal welding.
- Page 10 OPERATION (cont.) Electricity The electricity flows through the electrode cable to the attached electrode. The electricity will not leave the electrode unless it touches an earthed object. Electricity always finds the fastest path to the earth. When the earth cable clamp is connected to the metal work piece a direct earth connection is created back to the welder.
- Page 11 SPECIFICATIONS - MODEL NO. MSH-115 6. Position the two pieces of metal you wish to join. 7. Hold the electrode approximately 2 cm away from the desired join area. Lower or hold the welding mask over your face. Lower the electrode slowly and proceed to strike the electrode tip against the desired join area on the work piece as if you are striking a match.
-
Page 12: Maintenance
Keep the ventilation slots of the welder clear at all times and prevent foreign matter from entering the housing. Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the welder by an unauthorised person or by mishandling of the welder. -
Page 13: Contents
Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. CONTENTS 1 x Arc Welder AWG-964 1 x Welding Mask 1 x Combination wire brush 1 x Instruction Manual... -
Page 14: Warranty
PURCHASED FROM: ________________________________________________ DATE PURCHASED: ________________________________________________ 3 YEAR REPLACEMENT WARRANTY Your Ozito product is guaranteed for a period of 36 months from the original date of purchase and is intended for DIY (Do it yourself) use only. WARNING The following actions will result in the warranty being void.
Need help?
Do you have a question about the AWG-964 and is the answer not in the manual?
Questions and answers