DeLonghi HCA 530FTSW Instruction Booklet
DeLonghi HCA 530FTSW Instruction Booklet

DeLonghi HCA 530FTSW Instruction Booklet

Electric heating convector

Advertisement

5713003700
11-06-2002
14:03
Pagina 1
ELECTRIC HEATING CONVECTOR
Instructions booklet
Please keep in a safe place as you may need to refer to them at a later date

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HCA 530FTSW and is the answer not in the manual?

Questions and answers

Lynn Smith
January 24, 2025

The timer is off. The four power lights are plashing and I cannot control them.

1 comments:
Mr. Anderson
February 10, 2025

To fix the timer issue on the DeLonghi HCA 530FTSW, ensure the plug is connected to the power supply, as the timer functions like an electric clock and stops working when power is lost. If the power was disconnected, reset the clock by setting the correct time. To program the timer, push out the notches on the dial corresponding to the desired operating time (each notch represents 15 minutes). Ensure the timer shows the correct time before selecting the desired function.

If the power light is not working, check that the heater is plugged in and the power supply is functioning. If the power cable is damaged, it must be replaced by the manufacturer or an authorized service center. If the issue persists, further inspection by a professional may be required.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for DeLonghi HCA 530FTSW

  • Page 1 5713003700 11-06-2002 14:03 Pagina 1 ELECTRIC HEATING CONVECTOR Instructions booklet Please keep in a safe place as you may need to refer to them at a later date...
  • Page 2: Timed Operation

    5713003700 11-06-2002 14:03 Pagina 2 Power selector Thermostat dial Timer Turbo fan switch Fig.1 Fig.2 Fig.3 MANUAL (Timer override) TIMED OPERATION HEATER OFF Fig.4...
  • Page 3: General Instructions

    5713003700 11-06-2002 14:03 Pagina 3 GENERAL INSTRUCTIONS Remove the heater from the packaging. Check that neither the heater nor the power cable has been damaged during transport. Do not operate the heater if damaged. Your convector is suitable for either freestanding or wall mounting usage. Do not assemble the feet if wall mounting. ASSEMBLING THE FEET To fit the feet to the appliance, proceed as follows: Insert the foot into the slot at the side and push it in all the way until it hooks onto the two teeth (Fig.
  • Page 4 5713003700 11-06-2002 14:03 Pagina 4 This heater has ECC (electronic climate control) which automatically monitors and selects the ideal power to maintain a chosen temperature. HOW TO USE IT Insert the plug into the mains socket and switch on, pressing the button (fig.
  • Page 5: Using The Timer

    5713003700 11-06-2002 14:03 Pagina 5 Frost stat function Press the button, it is recommended to select maximum power level. Set the thermostat dial to the “ “ position (fig. 6). When set in this way, the appliance will switch on automatically only if the room temperature falls below 5°C, to prevent freezing, at minimum energy consumption.
  • Page 6: Maintenance

    5713003700 11-06-2002 14:03 Pagina 6 MAINTENANCE Before carrying out any maintenance, unplug the heater from the mains and wait for it to cool. The convector requires no particular maintenance. It is sufficient to remove the dust with a soft, dry cloth. Never use abrasive powders or solvents. If necessary remove concentrated areas of dirt with a vacuum cleaner.
  • Page 7 5713003700 11-06-2002 14:03 Pagina 7 5713003700/ 06.02...

Table of Contents