Table of Contents
Advertisement
Start by Reading These Important Safety Rules
These safety alert symbols mean WARNING - a personal safety or property damage instruction.
Read these instructions carefully.
This garage door opener is designed and tested to offer reasonable safe service provided it is installed and
operated in strict accordance with the following safety rules.
Failure to comply with the following instructions may result in serious personal injury or property damage.
WARNING: If your garage has no service entrance door, Model CM1702 Outside Quick Release must be installed. This accessory
allows manual operation of the garage door from outside in case of power failure.
Keep garage door balanced. Sticking or binding doors
must be repaired. Garage doors, door springs, cables,
pulleys, brackets and their hardware are under extreme
tension and can cause serious personal injury. Do not
attempt to loosen, move or adjust them. Call for garage
door service.
Do not wear rings, watches or loose clothing while
installing or servicing a garage door opener.
To avoid serious personal injury from entanglement,
remove all ropes connected to the garage door before
installing the door opener.
Installation and wiring must be in compliance with your local
building and electrical codes. This is a class 2 double
insulated product, connesction to earth is not required
or provided.
Lightweight doors of fiberglass, aluminum or steel
must be substantially reinforced to avoid door damage.
The best solution is to check with your garage door
manufacturer for an opener installation reinforcement kit.
The safety reverse system test is very important. Your
garage door MUST reverse on contact with a 40mm
obstacle placed on the floor. Failure to properly adjust the
opener may result in serious personal injury from a closing
garage door. Repeat the test once a month and make
any needed adjustments.
This unit should not be installed in a damp or wet space.
Door must not extend over a public byway during
operation.
Table of Contents
Completed Installation
Adjustment
(Optional)
Wiring the Lighted
Door Control Button (Optional)
Accessories& Replacement Parts
Page
Illustration(s)
1
1
1
1
1
2
1
3
1
4
2
5 - 11
2
12 - 17
3
18 - 20
3
19
3
3
20
3
21
3
4
4
4
5
22
5
23
5
Fasten the child warning label adjacent to the lighted door
control button as a reminder of safe operating procedures.
Disengage all existing garage door locks to avoid
damage to garage door.
Any door control buttons (if installed) MUST be located
where the garage door is visible, but out of the reach of
children. Do not allow children to operate push
button(s) or remote control(s). Serious personal injury
from a closing garage door may result from misuse of
the opener.
Activate opener ONLY when the door is in full view, free
of obstructions and opener is properly adjusted. No
one should enter or leave the garage while the door is
in motion. Do not allow children to play near the door.
Use manual release only to disengage the trolley and, if
possible, ONLY when the door is closed. Do not use the
red handle to pull the door open or closed.
Disconnect electric power to the garage door opener
before making repairs or removing covers.
This product is provided with a transformer and power
supply cord of special design which, if damaged, MUST be
replaced
by
Chamberlain Anz distributor and fitted by a specialist.
SAVE THESE INSTRUCTIONS
Before You Begin
1. Look at the wall or ceiling above the garage door. The header
bracket MUST be securely fastened to structural supports.
2. Do you have a finished ceiling in your garage? If so, a support
bracket and additional fastening hardware (not supplied) may be
required.
3. Do you have an access door in addition to the garage door? If
not, Model CM1702 Outside Quick Release Accessory is
required.
1
Door Types
A. One-Piece Door with Horizontal Track Only
B. Sectional Door with Curved Track
NOTE: Unit will not work with One-Piece Doors with Horizontal and
Vertical Tracks, Double-Wing Doors, or Canopy Doors.
2
Tools Required for Installation
3
Hardware Provided
ASSEMBLY HARDWARE
1. Square Head Screws
2. 8mm Carriage Bolt
3. Cable Pulley
INSTALLATION HARDWARE
7. 6mm Nut
9. 6mm Lag Bolt
a
transformer
from
your
4. Pin
(4)
5. 8mm Lock Nut
(1)
6. Pulley Bracket
(1)
(8)
(4)
(4)
14. C rail Bracket
(4)
local
(1)
(1)
(1)
(3)
(2)
(1)
Hide quick links:
Advertisement
Table of Contents
