Cobra SLR 650G Operating Instructions

Thank you for purchasing Cobra
Radar/Laser/Camera Detector. Please familiarize yourself with the
capabilities your new detector can provide by reading this manual.
Also, please be careful when using your new detector while driving.
Powering Unit On/Off & Mounting Unit
Plug in the detector using the included cigarette lighter power cord.
Press the Power button momentarily to turn the unit On (or Off).
Note: To change display orientation, press and hold the Power
button for 2 seconds.
a. Windshield Mount
Insert bracket
here
Model SLR 650G
Power Jack
Operating Instructions
Power Button
Supercharged Long-Range Lift lever on suction cup base before attaching to the windshield.
Radar/Laser/Camera Detector Once attached, push against windshield and lock the lever down.
Use the ball-joint adjustment and make sure the detector unit is
NOTE: This device complies with part 15 of FCC rules: Operation is subject
aligned level and pointing straight ahead. The display can be in
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received
flip-up or flip-down position to suit preferred mounting location,
including interference that may cause undesired operation.
CAUTION: Modifications or parts not approved by Cobra Electronics
and rotated to face directly toward you. Renew suction cup with
Corporation may violate FCC Rules and void authority to operate this equipment.
a damp cloth or by rinsing under tap water.
® Vedetta ™ Series, Model SLR 650G
b. Dash Mounting
For dash mounting, use the enclosed hook & loop fastener
with double-sided tape. Simply attach it to the bottom of the
unit with display in flip-up position.
Touch-Point Controls
Volume
Left
Scroll
Attach to windshield
City/Highway
Mode
Select
Appropriate touch-point icons will light up automatically to
show you available options. Touch the touch-point icons to
activate corresponding function.
Touching Volume touch-point while receiving an alert
will mute the audible alert. Touching Display Brightness
touch-point will turn off the display.
Types of Screens
1. Menu/Settings Screen
Alert Settings
Display
GPS
Brightness User
Settings
Settings
Right
Scroll
Menu/Save
& Exit
User Settings:
For customizing settings for IntelliMute, Auto Mute, Voice/Tone
Alerts, Color Themes, Smart Power and Reset to Factory Default.
Alert Settings:
For customizing settings to turn on/off certain individual radar
bands and Low Car Battery Warning.
GPS Settings:
For customizing settings for Speed Format, User-set Speed Alert,
turn on/off certain individual Location-based Alerts, IntelliScope,
AURA Database Info, and Delete User LBAs.
Navigate through Settings using the scroll touch-point.
Press Select to confirm and Menu to save and exit.
2. Standby Screen 3. Radar/Laser Alert Screen
Radar bands consist of X-band, K-band, Ka-band, and Ku-band.
With Radar signals, the signal strength meter shows signal strength
of the radar gun as well as relative proximity to the source. With
Compass Vehicle
Heading Speed
Ka-band, you will also be notified of the actual Ka-band radar gun
frequency being used.
City/Highway Vehicle
Indicator Battery
Signal Strength
Voltage
IntelliMute Indicator
Compass Heading: Ka Band Alert
Automatically displays GPS-based heading. If a GPS signal cannot
be received will be displayed.
Vehicle Speed:
With Laser signals, you will always receive full alert and pulse rate
Automatically displays your current vehicle speed using GPS. If a
(PPS) of the corresponding laser gun being used. Laser PPS cur-
GPS signal cannot be received will be displayed.
rently in use are: 100, 125, 130, 200, 238 and 340.
City/Highway Indicator:
Shows curent filtering mode.
Vehicle Battery Voltage:
Displays your car battery voltage and automatically warns you if
this drops below 11.9V.
IntelliMute Indicator:
See reverse of this manual.
Frequency
Laser
Pulse
Rate