Table of Contents
Advertisement
¬
PD5N ..........................................................................................1-2
l Specifications.........................................................................1-2
l Layout diagram......................................................................1-4
¯
System block diagram ................................................................ 1-11
¬
Standard External Connectors......................................................2-3
-
Jumpers and Switches ................................................................ 2-10
®
Presentation and Installation of the CPU .................................... 2-11
¯
¬
Standard CMOS Setup Menu.......................................................3-4
-
BIOS Features Setup Menu .........................................................3-6
®
Chipset Features Setup Menu..................................................... 3-12
¯
Power Management Setup Menu................................................ 3-14
°
PCI & Onboard I/O Setup.......................................................... 3-18
±
Load BIOS Defaults .................................................................. 3-23
²
Load Setup Defaults .................................................................. 3-23
³
Password Setting ....................................................................... 3-24
´
IDE HDD Auto Detection ......................................................... 3-35
Chapter 4
Appendix B Intel Pentium CPUs
Appendix C AMD-K5 CPUs
Table of Contents
VGA Installation
DRAM Memory ¡j ......... 2-21
Advertisement
Table of Contents
Related Manuals for Abit PD5NE
Summary of Contents for Abit PD5NE
-
Page 1: Table Of Contents
Table of Contents Chapter 1 Introduction of PD5N Features ¬ PD5N ..................1-2 l Specifications.................1-2 l Layout diagram..............1-4 ¯ System block diagram ..............1-11 Chapter 2 Installing the Mainboard ¬ Standard External Connectors............2-3 Jumpers and Switches ..............2-10 ® Presentation and Installation of the CPU ........2-11 ¯... - Page 2 Chapter 1 -2 Appendix D Cyrix 6x86 CPUs Appendix E General Discussion about HDD Installation Appendix F Technical Support Appendix G Flash BIOS User Instructions...
-
Page 3: Chapter 1 Introduction Of Pd5N Features
Introduction of PD5N Features Chapter 1 Introduction of PD5N Features The PD5N have been especially designed for File server, Workstation and Professional users. It can support a wide range of processors, including all Intel CPUs (P54C) and Intel CPUs with MMX (P55C), as well as all AMD- K5/K6 and Cyrix 6x86/6x86L/6x86MX CPUs. -
Page 4: Specifications
Chapter 1 ¬ Specifications 1. Support AT/ATX power supply 2. Adjustment for Frequency and Voltage Using DIP switch or jumper wires to adjust the frequency and voltage on the mainboard 3. Uses ZIF CPU Socket 7 for easy CPU installation l Support switching power for CPU to get more stable environment l Supports Intel Pentium CPUs:75~200MHz and P55C CPUs with MMX (166~233MHz) - Page 5 Introduction of PD5N Features l Two Universal Serial Bus (USB) ports l Four fast IDE channels (PIO mode 0~4, Ultra “DMA/33” and Bus Master) l One EPP/ECP parallel port and two 16550A serial ports l Two floppy disk drive connectors (FDD) (360K, 720K, 1.2M, 1.44M and 2.88M) l Support PS/2 type mouse 10.
-
Page 6: Layout Diagram
Chapter 1 Layout diagram Fig 1-1 Layout diagram... -
Page 7: System Block Diagram
Introduction of PD5N Features ® System block diagram Pentium Processor 3.3v Host BUS Control Address Data Cntrl Addr CACHE Tag Cntrl Cntrl Main (SRAM) Memory (DRAM) TIO[0..7] SiS 5598 Data CD ROM& Hark Disk Universal Serial Bus ISA Device(s) PCI BUS Control ISA BUS Address/Data... -
Page 9: Chapter 2 Installing The Mainboard
Installing the Mainboard Chapter 2 Installing the Mainboard This PD5N mainboard not only provides all standard equipment for classic personal computers, but also provides great flexibility for meeting future upgrade demands. This chapter will introduce step by step all the standard equipment and will also present, as completely as possible future upgrade capabilities. - Page 10 Chapter 2 & User friendly instructions Our objective is to enable the novice computer user to perform the installation by themselves. We have attempted to write this document in a very clear, concise and descriptive manner to help overcome any obstacles you may face during installation.
-
Page 11: Standard External Connectors
Installing the Mainboard ¬ Standard External Connectors Inside the case of any computer several cables and plugs have to be connected. These cables and plugs are usually connected one-by-one to connectors located on the mainboard. You need to carefully pay attention to any connection orientation the cables may have and, if any, notice the position of the first pin of the connector. - Page 12 Chapter 2 PN1 - Power ON/OFF switch There is no specific orientation. Since most cases do not support this feature, most of you ignore this instruction. Pin number Name or significance of the signal Power on/off Ground PN1 - SMI Switch There is no specific orientation.
- Page 13 Installing the Mainboard PN2 - Hardware Reset connectors There is no specific orientation. Connect the two-thread hardware reset cable to the PN2 connector pins on the mainboard. Pin number Name or significance of signal Hardware reset signal Ground FAN1 - CPU Fan power connector This has a specific orientation.
- Page 14 Chapter 2 in the correct orientation, and to connect connector of the power supply unit to the connector on the mainboard. Name of the signal or Name of the signal or Pin number Pin number signification signification +3.3VDC +3.3VDC +3.3VDC -12VDC Ground Ground...
- Page 15 Installing the Mainboard Mouse - PS/2 Mouse connector(J4) Watch the pin number and the orientation his has a specific orientation. Connect the six-threads PS/2 Mouse cable provided to the connector on the mainboard. Pin number Name of the signal or signification Mouse data No connection Ground...
- Page 16 Chapter 2 IDE 2 IDE Channel 2 Floppy Disk connector Parallel port connector COM1 Serial port COM1connector COM2 Serial port COM2connector VGA connector Feature FEATURE connector Universal Serial Bus connector...
-
Page 17: Jumpers And Switches
Installing the Mainboard - Jumpers and Switches CCMOS(JP9) : Delete the contents of the CMOS This jumper is set on pins 1 and 2 at the factory, in order for the computer to function normally, so please do not change this setting. The main feature of this jumper is to solve situations where the computer crashes due to improper usage. -
Page 18: L Specifications
2-10 Chapter 2 ® Presentation and Installation of the CPU Since 1996, every two or three months, Intel adds new models to the Pentium CPU series. That is why the CPU market is filled with a lot of different models and brands. All CPUs have different electrical specifications. That’ s why installing a CPU is becoming more and more complex. - Page 19 Installing the Mainboard 2-11 Internal clock Also referred to as the real internal CPU clock, it is the actual internal operating clock of the CPU. The Internal Clock is a multiple of the external clock and of the clock multiplier factor. For instance, the Intel Pentium 90 CPU has a 60MHz external clock and its clock multiplier factor is 1.5;...
- Page 20 2-12 Chapter 2 P-Rating The P-Rating was defined by some manufacturers other than Intel to rate the performance of their CPU in comparison with Intel Pentium CPUs. For instance, Cyrix 6x86 P166+ has a higher actual speed compared with Intel Pentium P166, its internal clock needs only 133MHz versus 166MHz for Intel’...
- Page 21 Installing the Mainboard 2-13 External Internal External clock Factor Reserve External clock Frequency Intel Pentium clock clock / with MMX 50MHz 75MHz OFF 60MHz 90MHz OFF P100 66MHz 100MHz OFF P120 60MHz 120MHz ON P133 66MHz 133MHz ON P150 60MHz 150MHz ON P166 66MHz 166MHz ON P200...
- Page 22 2-14 Chapter 2 Cyrix/IBM 6x86/6x86L CPU External Internal External clock Factor Reserve External clock Frequency Cyrix / IBM clock clock 6x86/6x86L PR120+ 50MHz 100MHz ON PR133+ 55MHz 110MHz ON PR150+ 60MHz 120MHz ON PR166+ 66MHz 133MHz ON PR200+ 75MHz 150MHz ON 6x86MX PR166 66MHz 133MHz ON...
- Page 23 Installing the Mainboard 2-15 2.CPU Voltage and Setup (SW2) For the voltage of 586 serials of CPU, there are two kinds of operation mode depend different CPUs, single voltage and dual voltage. Please make sure which kind of CPU and the working voltage that you used before you install.
-
Page 24: Installing System Memory ¡I Dram Memory ¡J
2-16 Chapter 2 ¯ Installing System Memory DRAM ¡i Memory ¡j When this mainboard was designed, we not only have taken into account the present needs, but we have also tried to care about demands for future upgrades: 2. 72-pin SIMM sockets: PD5N support four 72 pin SIMM sockets 3. - Page 25 Installing the Mainboard 2-17 3. Maximum memory capacity 384M bytes supported by this mainboard. ¡i Relationships between memory modules and Pentium Computer CPUs ¡j knowledge Pentium, Cyrix 6x86 and AMD-K5/K6 are all 64 bit CPUs, but 72-pin SIMM modules are only 32-bit. That’ s why they have to be used in pairs, because the CPU will always be only able to see 64 bits.
- Page 26 2-18 Chapter 2 You can also directly refer to table 2-1.
- Page 27 Installing the Mainboard 2-19 Table 2-1 72-pin SIMM Module Installation ¡i SIMM1, SIMM2 ¡j ¡i SIMM3, SIMM4 ¡j Total memory size ¡i pair ¡j ¡i pair ¡j 1Mx32 ¡i 4Mx2 ¡j 2Mx32 ¡i 8Mx2 ¡j 16MB 4Mx32 ¡i 16Mx2 ¡j NO MODULE INSERTED 32MB 8Mx32 ¡i...
-
Page 29: Chapter 3 Introduction Of Bios
Interuction of BIOS Chapter 3 Introduction of BIOS The BIOS is a program located on a Read-Only Memory chip on the mainboard. This program will not be lost when you turn the computer off. This program is also referred to as the boot program. It is the only channel for the hardware circuit to communicate with the operating system. - Page 30 Chapter 3 Three to five seconds after the message is displayed, if you press the Del key, or if you press simultaneously the Ctrl Alt Esc keys, you will access the BIOS Setup menu. At that moment, the BIOS will display the following message: Fig 3 BIOS Setup main menu...
- Page 31 Interuction of BIOS Computer CMOS DATA knowledge Maybe you have heard somebody saying that their CMOS DATA was lost. What is the CMOS? Is it important? The CMOS is the memory used to store the BIOS parameters that you have configured. This memory is passive. You can read its data, and you can also store data in it.
-
Page 32: Standard Cmos Setup Menu
Chapter 3 ¬ Standard CMOS Setup Menu It is the basic configuration parameters of the BIOS. These parameters include the settings of date, hour, VGA card, FDD and HDD. Fig 3-2 Standard CMOS Setup Menu l Set up of HDD operating mode ¡i NORMAL, LBA, LARGE ¡j Since old operating systems were only able to support HDD whose capacity... - Page 33 Interuction of BIOS ä LBA (Logical Block Addressing) mode: LBA mode supports hard disk drives up to 8.4Giga. This mode uses a different method to calculate the position of disk data to be accessed. It translates Cylinders (CYLS), Heads and Sectors into a logical address where data are located.
-
Page 34: Bios Features Setup Menu
Chapter 3 - BIOS Features Setup Menu BIOS Features Setup Menu has already been set for maximum operation. If you do not really understand each of the options in this menu, we recommend you use default values. In each item, you can press <F1> at any time to display all the options for this item. -
Page 35: Quick Power On Self Test
Interuction of BIOS CPU External Cache: This item is used to enable or to disable the CPU external cache. When the external cache is enabled, the system works faster. The default is Enable. Quick power on self test: After the computer has been powered on, the BIOS of the mainboard will run a series of tests in order to check the system and its peripherals. -
Page 36: Ide Hdd Block Mode
Chapter 3 ä On: At boot up, the Numeric Keypad is in numeric mode. ä Off: At boot up, the Numeric Keypad is in cursor control mode. IDE HDD Block Mode: This item can be set as Enable or Disable. Most of new hard disk drives (IDE drives) support multi-sector transfers. -
Page 37: Security Option
Interuction of BIOS Security Option: This option can be set to System or to Setup. After you have created a password through PASSWORD SETTING, this option will deny access to your system (System) or modification of computer setup (BIOS Setup) by unauthorized users. ä... - Page 38 3-10 Chapter 3 Video BIOS Shadow: This option is used to define whether the BIOS on the video card uses shadow feature or not. You should set this option to Enable, otherwise the display performance of the system will greatly decrease. Shadowing address ranges (C8000-CBFFF Shadow): This option allows you to decide if the memory block (BIOS) of an interface card at the address C8000-CBFFF uses the shadow feature or not.
- Page 39 Interuction of BIOS 3-11 This option allows you to decide if the memory block (BIOS) of an interface card at the address DC000-DFFFF uses the shadow feature or not. If you have no interface card using this memory block, don’ t enable this option.
-
Page 40: Chipset Features Setup Menu
3-12 Chapter 3 ® Chipset Features Setup Menu The Chipset Features Setup Menu is used to modify the contents of the buffers in the chipset on the mainboard. Since the parameters of the buffers are closely related to hardware, if the setup is not correct or false, the mainboard will become unstable or you will not be able to boot up. -
Page 41: Vga Shared Memory Size
Interuction of BIOS 3-13 DRAM settings: The other DRAM settings are all closely related to hardware. If you do not understand this very well, don’ t make any changes. Our BIOS is able to autodetect the characteristics of your DRAM and to choose the best settings. -
Page 42: Power Management Setup Menu
3-14 Chapter 3 ¯ Power Management Setup Menu The difference between Green PCs and traditional computers is that Green PCs have a power management feature. With this feature, when the computer is powered on but inactive, the power consumption is reduced in order to save energy. When the computer operates normally, it is in Normal mode. -
Page 43: Power Management
Interuction of BIOS 3-15 back to the Main Menu. We are now going to briefly explain the options in this menu: Power Management: Four options: ä User Define User Define defines the delay for accessing the power modes. ä Disable Disable Power Management features. -
Page 44: Doze Mode
3-16 Chapter 3 Video Off After: Select the saving mode in which the video is switched off. ä Always On The video will never be switched off in no saving mode. ä All Modes Off The video will be switched off in all saving modes. ä... - Page 45 Interuction of BIOS 3-17 can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Standby power saving mode.
-
Page 46: Suspend Mode
3-18 Chapter 3 Suspend Mode: When the setting selected for "Power Management" is "User Define", you can define for this mode any delay from 1 minute to 1 hour. If no power management event occurs during this time period, meaning the computer is inactive during this period, the system will enter the Suspend power saving mode. -
Page 47: Pci & Onboard I/O Setup
Interuction of BIOS 3-19 ± PnP, PCI & Onboard I/O Setup In this menu, you can change the INT# and IRQ of the PCI bus and the onboard I/O device, I/O port address and other hardware settings. Fig 3-6 PCI & Onboard I/O Setup Force Update ESCD: If you want to clear ESCD data next time you boot up, and ask the BIOS to reset the settings for the Plug &... -
Page 48: On Board Serial Port 1
3-20 Chapter 3 PCI IDE Card 2nd Channel: This option can be enabled or disabled. BIOS default is Enable. Since this channel uses IRQ15, if you want to use this channel, you have to enable this option to make the BIOS assign IRQ15 to this channel. PCI IDE Card IRQ Map to: Three options are available for this item: PCI Auto, PCI-slotX and ISA. -
Page 49: On Board Parallel Port
Interuction of BIOS 3-21 Attention:Do not select the same I/O address and IRQ for the two serial ports, otherwise the serial ports will not be able to operate normally. / Onboard IR Function: Onboard serial port 2 can support IR (Infrared) function. Three options are available: ä... -
Page 50: On Board Ide Controller
3-22 Chapter 3 On board IDE Controller: Onboard PCI IDE controller can be set as IDE-1, IDE-2, Both or Disable. / Master drive PIO Mode: ä Auto: the BIOS can auto-detect the PIO mode of the HDD in order to set its data transfer rate. (Default) ä... -
Page 51: Load Bios Defaults
Interuction of BIOS 3-23 ± Load BIOS Defaults BIOS defaults are the reference settings that allow your system to work at a comparatively low performance. When you choose the option, the following message is displayed: “Load BIOS Defaults (Y/N)? N” If you want to use BIOS default values, press “Y”, than <Enter>. -
Page 52: ³ Password Setting
3-24 Chapter 3 ³ Password Setting This option allows you to set a password required to start the system (System) or to access to the BIOS (Setup). After you have set a password through the PASSWORD SETTING option, you can enter the Security Option in the “BIOS Features Setup Menu” to select the security level in order to prevent any unauthorized access. -
Page 53: Ide Hdd Auto Detection
Interuction of BIOS 3-25 ´ IDE HDD Auto Detection After you have installed the hard disk, in old systems, you had to know the hard disk specifications, such as the number of cylinders, heads and sectors, and to enter the relevant information into the hard disk information section. If the CMOS data were erased, and you had forgotten the hard disk specifications, it was a great problem. -
Page 55: Dos Utility
VGA Driver Setup Chapter 4 VGA Driver Setup DOS Utility 1.1. SVGAUTL.EXE 1.1.1 General Description SVGAUTL.EXE is one of the utilities of PD5N. It supports three functions: (1) Video Mode Setting (2) Frame Rate Setting (3) Power Saving Setting You can use SVGAUTL.EXE to select the desired video mode. For 640x480, 800x600, 1024x768, and 1280x1024 resolutions, PD5N supports multiple frame rates. -
Page 56: What The Parameters Stand For
Chapter 4 1.1.3 What the Parameters Stand for? The meaning of parameters used by SVGAUTL.EXE are explained below: Syntax: >SVGAUTL [/D:mode_no] [/F0:n0] [/F1:n1] [/F2:n2] [/F3:n3] [/PA:ta] [/PB:tb] where /D: Set the Video Mode to be mode_no which is a hex number. For example:Set 1024x768 256 color graphic mode. -
Page 57: Autocad R11 Setup
VGA Driver Setup 1.2 Autodesk ADI 4.2 -Protected Mode 1.2.1.1 Unpack & Copy To unpack and copy drivers to where they should resides, please follow the following procedures: (1) Run "INSTDRV.EXE" where it resides. For example, A:\> INSTDRV <Enter> (suppose INSTDRV.EXE resides in Driver Disk #1 ) or D:\>... -
Page 58: Autocad R12 Setup
Chapter 4 1.2.3 AutoCAD R12 Setup (1) The following procedures assume that 1 - You have complete "unpack & copy" procedure. 2 - Your SiS ADI 4.2 drivers are located in C:\ADI42. 3 - Your AutoCAD R12 program is located in C:\ACADR12. 4 - Your AutoCAD R12 default drivers are located in C:\ACADR12\DRV. - Page 59 VGA Driver Setup 1.2.4 AutoShade R2.0 Setup (1) The following procedures assume that (a) You have complete "unpack & copy" procedure. (b) Your ADI 4.2 drivers are located in C:\ADI42. (2) Add the following settings to your batch file for AutoShade R2.0 (say SHADE2.BAT) or to your "AUTOEXEC.BAT"...
- Page 60 Chapter 4 1.2.5 3D Studio Version 3.0 Setup (1) The following procedures assume that 1 - You have complete "unpack & copy" procedure. 2 - Your ADI 4.2 drivers are located in C:\ADI42. (2) Create your own 3D Studio V3.0 batch file (say 3DS3.BAT) and add the following settings to it, or add the following settings to your "AUTOEXEC.BAT"...
- Page 61 VGA Driver Setup move cursor to "RCPADI" or "RDPADI". Press <Enter> to select. 4 - Complete the other selections and exit configuration. (9) After exit configure, 3DS will boot automatically using the environment you just select. (10) If your previous configuration is OK, 3DS will ask you to make detail configuration for SiS 5597/5598 drivers.
- Page 62 Chapter 4 2. Windows NT 3.5 & 3.51 2.1 Installation (1) Select Control Panel from Main group. (2) Select Display icon. (3) Select Change Display Type from Display Settings. (4) Select Change from Display Type. (5) Select Other from Select Device. (6) Place the Windows NT 3.51 Installation Disk (Diskette #1) into Floppy Drive (7) When the "Install from Disk"...
- Page 63 VGA Driver Setup 3. Windows NT 4.0 3.1 Installation (1) Click "Start" menu and select Control Panel from Settings group. (2) Select Display icon. (3) Select Settings of Display Properties. (4) Select Display Type. (5) Select Change from the Adapter Type area. (6) Select Have Disk of Change Display.
- Page 64 4-10 Chapter 4 Windows 95 Installation (1) Click "Start" menu and select Control Panel from Settings group. (2) Select "Display" icon. (3) Select "Settings" index in the display properties sheet. (4) Select "Advanced Properties" button.
- Page 65 VGA Driver Setup 4-11 (5) Select "Change..." button in "Adapter Type" group.
- Page 66 4-12 Chapter 4 (6) Select "Have Disk" button.
- Page 67 VGA Driver Setup 4-13 (7) Place the Windows 95 Installation Disk (Diskette #2) into Floppy Drive The directory in CD-Title is at "D:\MM\WIN95". (8) When the "Install from Disk" dialog box appears, type the directory storing the drivers and click "OK". The directory in Diskette #2 is at "A:\".
- Page 68 4-14 Chapter 4 4.3 Utilities (1) Place the Windows 95 Installation Disk into Floppy Drive or Place the PD5N CD-Title Disk into CD-ROM Drive. (2) Click "Start" menu and select "Run..." menu item. (3) In "Run" dialog, typing the source execution file then press "OK". The execution file in Diskette #2 is at "A:\SETUP.EXE".
-
Page 69: Installation Procedures
VGA Driver Setup 4-15 5. Windows 3.1 5.1 Installation 5.1.1 Installation Procedures (1) Click "File" menu and select "Run..." menu item. (2) In "Run" dialog, typing the source execution file then press "OK". The execution file in Diskette#5 is at "A:\SETUP.EXE". The execution file in CD-Title is at "D:\MM\WIN31\SETUP.EXE". - Page 70 4-16 Chapter 4 In "SiS VGA Configuration System" screen, choose "zooming" item to define "hot keys" for zoom-in or zoom-out screen without entering setup program. The operation principles of zoom-in and zoom-out are as follow: 1- The resolution change sequence for zoom-in is 1024x768 ===>...
-
Page 71: Video Operations
VGA Driver Setup 4-17 5.2 Video Operations 5.2.1 DCI Function SiS 5597/5598 supports DCI driver for software MPEG playback and other media player programs which could take advantage of DCI. The SiS 5597/5598 DCI driver is automatically loaded during "Windows Driver Unpack &... - Page 72 4-18 Chapter 4 5.2.3 Note on DCI & MMPlay MMPLAY.EXE Button Description Power On/Off Open File & Type Control Minimize This Application Eject CD Title(Not implemented yet.) Fast Backward Fast Forward Mark in Mark out Pause Play Stop Home Volume increase(Not implemented yet.) Volume decrease(Not implemented yet.)
-
Page 73: Appendix A Quick Installation
Quick Installation Appendix A Quick Installation Appendix A will give you a simplified installation procedure, in order to allow you to install tour mainboard quickly and correctly. If you need further information or if you need to change some other settings, read from Chapters 1. - Page 74 Appendix A Installing HDD: IDE1- Connect one end of the 40-pin cable that comes with the drive to the HDD connector, and the other end to IDE1 pin connector on the mainboard. Note: Be sure that the red line on the cable connects to the first pin of the connectors.
- Page 75 Quick Installation Watch the pin position and the Installing HDD LED connector: orientation PN1 - There is a specific orientation for pin 7 and pin 8. Connect the two-threads IDE LED connector to the connector on mainboard. Pin number Name of the signal or signification HDD LED signal ¡i LED Cathode ¡j HDD LED signal ¡i LED Anode ¡j Installing Suspend and Power ON/OFF switch connector:...
- Page 76 Appendix A Installing speaker connector: PN2 - There is no specific orientation for pin 4 to pin 7. Connect the four-threads speaker cable to the PN2 connector pins on the mainboard Pin number Name of the signal or signification +5VDC Ground Ground Sound Signal...
- Page 77 Quick Installation Pin number Name of the signal or Pin number Name of the signal or signification signification POWERGOOD Ground +5VDC Ground +12VDC -5VDC -12VDC +5VDC Ground +5VDC Ground +5VDC KB1 - There is an orientation pin. Installing Keyboard connector: Connect your keyboard connector to connector on the mainboard.
- Page 78 Appendix A Adjusting other jumpers: Some jumpers are reserved for future functions or are not to be adjusted in normal operation. Adjust them according to the following recommendations. CCMOS ¡G Put jumper on pin 1 and pin 2. BIOS Setup: Parameters and CPU settings After you have followed the steps described above and completed the installation, when you power the computer on, you will see the following message displayed:...
-
Page 79: Intel Pentium Cpus
Intel Pentium CPUs Appendix B Intel Pentium CPUs Pentium 75MHz Internal External Power Speed Spec. Clock Factor Clock Vcore Timing Supp. Note P54CS Q0649 75MHz 50MHz P54C Sx753 75MHz 50MHz P54C SX961 75MHz 50MHz P54C 75 MHz SX969 75MHz 50MHz P54C Q0700/S 75MHz... - Page 80 Appendix B Pentium 90MHz Internal External Power Speed Spec Clock Factor Clock Vcore Timing Supp. Note P54C Sx653 90MHz 60MHz P54C Sx957 90MHz 60MHz P54C Q0654 90MHz 60MHz P54C Sx958 90MHz 60MHz P54C 90 MHz Q0655 90MHz 60MHz P54C Sx959 90MHz 60MHz P54C...
- Page 81 Intel Pentium CPUs Pentium 100MHz Internal External Power Speed Spec Clock Factor Clock Vcore Timing Supp. Note P54C Sx886 100MHz 66MHz P54C Sx910 100MHz 66MHz P54C 100 MHz Sx956 100MHz 66MHz P54C Sx960 100MHz 66MHz P54C Q0657 100MHz 66MHz P54C Q0658 100MHz 66MHz...
- Page 82 Appendix B Pentium120MHz Internal External Power Speed Spec. Clock Factor Clock Vcore Timing Supp. Note P54CQS Q0708 120MHz 60MHz P54CQS 120 MHz Q0711 120MHz 60MHz Convert to P54C P54CQS Q0730 120MHz 60MHz P54CQS Sk084 120MHz 60MHz P54CQS Sk086 120MHz 60MHz Convert to P54C P54C Sx994...
- Page 83 Intel Pentium CPUs Pentium 133MHz Internal External Power Speed Spec Clock Factor Clock Vcore Timing Supp. Note P54CS Q0772 133MHz 66MHz P54CS Q0773 133MHz 66MHz P54CS Q0774 133MHz 66MHz P54CS Q0877 133MHz 66MHz P54CS Sk106 133MHz 66MHz P54CS S106J 133MHz 66MHz P54CS Sk107...
- Page 84 Appendix B Pentium 150MHz Internal External Power Speed Spec Clock Factor Clock Vcore Timing Supp. Note P54CS Q0835 150MHz 60MHz P54CS SY015 150MHz 60MHz P54CS Q0878 150MHz 60MHz PPGA P54CS SU071 150MHz 60MHz P55C 150 MHz Q0939 150MHz 60MHz 2.9V 3.3V CPGA P55C...
- Page 85 Intel Pentium CPUs Pentium 200MHz Internal External Power Speed Spec Clock Factor Clock Vcore Timing Supp. Note P54CS Q0951 200MHz 66MHz PPGA up P54CS SY045 200MHz 66MHz PPGA up P54CS 200 MHz Q0951F 200MHz 66MHz PPGA P54CS SY044 200MHz 66MHz PPGA P55C Q018...
- Page 86 Appendix B Y Bus Factor 3.15V~3.465V (Recommended voltage is 3.38V) Power STD 3.300V~3.465V (Recommended voltage is 3.38V) VRE 3.450V~3.6V (Recommended voltage is 3.52V) Timing STD Standard Timing Min. Delay (denoting shorter minimum valid delay AC timing for some signal) Supports timing for C55/C88 cache chipsets & design P54C 1.
- Page 87 AMD-K5 CPUs Appendix C AMD-K5 CPUs Recognizing AMD CPU speed, voltage and package: AMD-K5-PR100 A B Q xx Reserved Case Temperature Q= 60 ¢J R= 70 ¢J W=55 ¢J X= 65 ¢J Y= 75 ¢J Processor name Z= 85 ¢J Operating Voltage B= 3.45V-3.60V C= 3.30V-3.465V...
- Page 88 Appendix C...
-
Page 89: Cyrix 6X86 Cpus
Cyrix 6x86 CPUs Appendix D Cyrix 6x86 CPUs Recognizing Cyrix CPU speed and voltage: Name of the processor P-Rating 6x86, 6x86L 90+,120+,133+, 6x86MX 150+,166+,200+ 6x86-P166+ GP CPU Core Frequency 133 MHz 100,110,120, 133,150 3.52V (028) VCC Specification Full spec.: 3.15V-3.70V Center of Core C-spec. - Page 90 Appendix D...
- Page 92 Appendix F 4. DRIVER REV: Note the driver version number indicated on the DEVICE DRIVER disk as “Release *.**”. < Example: IDE Device Driver Drivers Diskette Release 1.09A Release 1.09A *5. OS/APPLICATION: Indicate what are the operating system and the applications your are running on the system. Example: MS-DOS 6.22, Windows 3.1.
- Page 93 Technical Support System Memory (DRAM): Indicate the brand and specifications (SIMM/DIMM) of your system memory. Examples: In the Brand space, write “Panasonic”, in the Specifications space, write “SIMM-FP DRAM 4MB-06”. Or, in the Brand, write “NPNX”, in the Specifications space, write “SIMM- EDO DRAM 8MB-06”.
-
Page 94: Technical Support Form
Appendix F & Technical Support Form ( Phone #: Company name: J Contact: /Fax #: Model BIOS ID # Mainboard model no. DRIVER REV OS/Application Hardware name Brand Specifications C.P.U IDE1 IDE2 CD-ROM Drive IDE1 IDE2 System Memory (DRAM) COAST ADD-ON CARD Problem Description:... - Page 95 SAVEBIOS “NEWBIOS” indicates file name for the new BIOS which can be Notes: downloaded from our website at http://www.abit.com.tw (user can choose a different file name in place of NEWBIOS). “SAVEBIOS” indicates the filename of the old system BIOS (user...
- Page 96 The content of the disk should be the following: a. Startup system files (COMMAND.COM, MSDOS.SYS, IO.SYS...) b. AWDFLSH.EXE c. The NEWBIOS file which can be downloaded from ABIT’ s website. d. AUTOEXEC.BAT, which has the following content: A:\AWDFLASH NEWBIOS ® When a version of BIOS that is for the incorrect mainboard model the following message will appear: “...
- Page 97 Super VGA User’s Manual Appendix H 5597/5598 Super VGA User’s Manual Appendix: H1. Video Modes H1.1 Standard VGA Modes MODE TYPE DISPLAY COLORS ALPHA BUFFER MAX. SIZE SHADES FORMAT START SIZE PAGES 320x200 40x25 B800 320x350 40x25 B800 8x14 360x400 40x25 B800 9x16...
- Page 98 Appendix H MODE DISPLAY COLORS FRAME H-SYNC. VIDEO SIZE SHADES RATE. FREQ. 320x200 31.5 K 25.1 M 320x350 31.5 K 25.1 M 360x400 31.5 K 28.3 M 320x200 31.5 K 25.1 M 320x350 31.5 K 25.1 M 360x400 31.5 K 28.3 M 640x200 31.5 K...
- Page 99 Super VGA User’s Manual H1.2 Enhanced Video Modes MODE TYPE DISPLAY COLORS ALPHA BUFFER MAX. SIZE SHADES FORMAT START SIZE PAGES 1056x352 132x44 B800 1056x350 132x25 B800 8x14 1056x364 132x28 B800 8x13 640x480 80x60 A000 720x480 80x60 B800 800x600 100x37 A000 8x16 800x600...
- Page 100 Appendix H MODE DISPLAY COLORS FRAME H-SYNC. VIDEO SIZE SHADES RATE. FREQ. 1056x352 30.5 K 40.0 M 1056x350 30.5 K 40.0 M 1056x364 30.5 K 40.0 M 640x480 31.5 K 25.1 M 720x480 31.5 K 25.1 M 800x600 35.1 K 30.0 M 800x600 37.9 K...
- Page 101 Super VGA User’s Manual MODE DISPLAY COLORS FRAME H-SYNC. VIDEO SIZE SHADES RATE. FREQ. 1280x1024 48.8 K 80.0 M 1280x1024 65.0 K 110.0 M 3An+ 1280x1024 80.0 K 135.0 M 320x200 31.5 K 25.1 M 320x200 31.5 K 25.1 M 320x200 16.8M 31.5 K...
- Page 102 Appendix H MODE DISPLAY COLORS FRAME H-SYNC. VIDEO SIZE SHADES RATE. FREQ. 49n## 1024x768 68.7 K 94.5 M 1024x768 35.5 K 44.9 M 1024x768 48.4 K 65.0 M 4An+ 1024x768 56.5 K 75.0 M 4An# 1024x768 60.2 K 80.0 M 4An## 1024x768 68.7 K...