Related Manuals for GE Monogram ZET737BW
Summary of Contents for GE Monogram ZET737BW
- Page 1 ® GE Monogram Installation Instructions 30" Built-In Ovens Models ZET757WW ZET757BW ZET737WW ZET737BW...
-
Page 2: Table Of Contents
CAUTION: • This oven should be installed by a qualified installer or service technician. • Never use the oven for warming or heating a room. Prolonged use of the oven without adequate ventilation can be hazardous. Contents Design Information Models Available ... -
Page 3: Models Available
ZET757WW available White double convection oven ZET757BW Black double convection oven ZET737WW White single convection oven ZET737BW Black single convection oven Dimensions Double oven and clearances A - 21" (533 mm) B - 23 -1/2" (597 mm) C - 29-3/4" (756 mm) D - 52-15/16"... -
Page 4: Cabinet Style Options
To obtain optimal appearance, cabinet cutouts must be exact. The examples shown here illustrate typical styles of 30" cabinets and oven fit. Installation instructions for each of these basic cabinetry styles are provided in this section. -
Page 5: Cabinetry
H Overall Height W Overall Width Use the information in this dimension drawing for typical framed cabinets. The front face of the oven will be flush with cabinetry doors or drawers. Order a 30" double oven cabinet. Rough opening for double oven must be: •... -
Page 6: Framed Cabinet Single Oven
H Overall Height W Overall Width Use the information in this dimension drawing for typical framed cabinets. The front face of the oven will be flush with cabinetry doors or drawers. Order a 30" single oven cabinet. Rough opening for single oven must be: •... -
Page 7: Frameless Cabinets
The front face of the oven will be flush with cabinetry doors or drawers. Whenever possible, order 30" frameless cabinet with the cutout sized to fit the oven. If you are using stock cabinets, additional finished filler pieces may be required to cover openings. -
Page 8: Single Oven Installed Below A Countertop
• Within 5" of the right side of the opening. • 22" min. above the support platform. • Gas or electric cooktops may be installed over this oven. See cooktop instructions for cutout dimensions. See label on the top of the oven for approved cooktop models. -
Page 9: Cabinetry Modification Suggestions
• The support must be level and rigidly mounted, flush with the bottom edge of the cutout. • The entire weight of the oven is supported by 2 x 4 runners or the solid floor and must be capable of supporting 275 lbs. -
Page 10: Determine Need For Filler Panels
The oven support floor and supports should be installed at the required locations. If there is a gap between the oven support floor and the bottom of the opening, a bottom filler panel should be constructed to fill the gap. -
Page 11: Cut Rail For Filler Panel
• The appearance panel width should match drawer fronts or doors. • Make the appearance panel appropriate height to fill the gap above or below the oven, allowing for reveals and overlaps to match existing drawers or doors. Determine... -
Page 12: Cut And Secure Cleats To Filler Panel
Cut and secure cleats to filler panel For the top filler panel: • Cut 2 cleats out of 3/4" thick material, approxi- mately 1-1/4" wide. • Cut the cleats to a length leaving approximately 1/2" at the bottom of the appearance panel to attach the rail. -
Page 13: Installation
Do not use an extension Note: cord with these appliances. Electrical locations For double oven: • Locate and install the junction box within reach of the power cord. – Approximately 5" from the right side of opening – 47" minimum above the cutout floor –... -
Page 14: Remove Oven Door
• Grasp each side of door, lifting up and off the hinges. • Cover hinges with toweling while working in oven area. The lower front trim is packed separately and should not be Note: attached until the oven is installed and secured to the installation opening. Connect CAUTION electrical installation or you may bend the Lower Side Trim. -
Page 15: Secure Oven To Cabinet
– Connect oven bare copper conductor to branch circuit ground lead (green or bare copper). Secure • Position the flexible conduit on top of the oven in oven such a manner that it will not interfere with proper to cabinet installation. -
Page 16: Attach Lower Trim
Attach • Attach the lower trim at the bottom of the oven: lower – Align the key slot on the trim piece to the rivets trim on the oven. – Push the trim down until it snaps into place. CAUTION cooling air to enter the cabinet. - Page 17 Notes Built-In Ovens...
- Page 18 Notes Built-In Ovens...
- Page 19 Notes Built-In Ovens...
- Page 20 Monogram. ® General Electric Company Louisville, KY 40225 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night.