GE Monogram ZBD6920PSS Dimensions And Specifications

ZBD6920PSS/ZBD6910PBB/ZBD6900PII
GE Monogram
Dimensions and Specifications (in inches)
• The dishwasher must be installed so that the drain hose
is no more than 10 feet in length for proper drainage.
• Water and power supply should enter in the
shaded area.
• Electrical and water connections are at the right front
of the dishwasher. The hot water line should extend
forward 30" to 40" from the rear wall. The electrical
must extend forward at least 24" to reach the junction
box.
• To prevent siphoning, an air gap must be used when
the waste tee or disposer connection is less than 18"
above the floor.
This Wall Area
must be Free of
Pipes or wires
34-1/2" Min.
Underside of 5" 5"
4"
Countertop
to Floor
24" Min.
Floor MUST
be Even with
Room Floor
* Dishwasher models
ZBD6900 and ZBD8900
require a 3/4" thick
custom panel and will be
24-3/4" deep.

Electrical Requirements

The dishwasher must be supplied with 120V, 60Hz, and
connected to an individual properly grounded branch
circuit protected by a 15- or 20-amp circuit breaker or
time-delay fuse.
For answers to your Monogram,
GE appliance questions, visit our website at
®
ge.com or call GE Answer Center
800.626.2000.
Fully Integrated Built-In Dishwashers
®
Cabinets
24"
Square
Min.
4"
and
Plumb
6"
*24"
24"
GE Profile or
® ™
service,
®
Custom Panel for Model ZBD6900PII
These dishwashers require a field installed 3/4" thick custom
panel and custom handle. An installation template is
packed with these models and may be obtained in advance.
Order Pub. No. 31-30569-1. Complete panel installation
instructions are included on the template.
CUSTOM PANEL SIZE REQUIREMENTS
HEIGHT
Panel height must
be between
30-1/16" and 30-1/4".
• If the panel height is
more than 30-1/4" it
will prevent the door
from swinging open.
• If the panel height is
less than 30-1/16" it
will not cover the
dishwasher door
frame.
• The top of the custom panel must be flush with the top
of the door. The 1/2" minimum gap between the top
of the door and the bottom of the countertop must be
maintained.
34"
Adjustable
WIDTH
to 35"
Panel width must be 23-3/4".
• If the panel width is less than
23-3/4" it will not cover the
dishwasher frame.
IMPORTANT: To ensure
optimum door balance
performance, the custom panel must not weigh
more than 14 lbs.
Accessories for custom panel model ZBD6900
ZPR0700S door panel provides a professional-style handle
on a stainless steel door panel.
ZTB700 stainless steel tubular handle for installation onto a
custom panel.
Before installing refer to installation instructions for
details. Pub. No. 31-30586
As an EnErgy StAr
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
23-3/4"
Countertop
Countertop
Minimum 1/2" gap
for Clearance
Minimum 1/2" gap
for Clearance
®
Specification Created 8/08
30-1/16" Min.
30-1/4" Max.
30-1/16" Min.
30-1/4" Max.
23-3/4"
1/2" min.
1/2" min.
Listed by
Underwriters
Laboratories
150051