Page 2
Drill 2 (two) 3/16″ pilot holes through studs or rear wall support 14-5/8″ to top of bracket REAR WALL MOUNTING TEMPLATE ALIGN BOTTOM EDGE WITH PENCIL LINE, INDICATING BOTTOM OF THE HOOD 49-80405 04-06 JR...
Page 4
*Height *Height Ceiling Ceiling 35 7/8” 20 7/16” 7/ 16 " * The Supplied Duct Cover Fits 8′ to 9′ 5″ Ceiling Heights. For 9′ 6″ to 10′ 5″ ceilings, order ZX90010. ″ ′ ″ ′ ″ ′ ″ 3 1/4 " 3 1/4”...
Page 6
Do not exceed maximum permissible equivalent lengths! ″ Any home ventilation system, such as a ventilation hood, may interrupt the proper flow of combustion air and exhaust required by fireplaces, gas furnaces, gas water heaters and other naturally vented systems.
Page 7
″ ″ ″ Measuring tape Pliers Electric drill with 5/16” and 3/8” Bits Duct tape Safety glasses 12” long Phillips Strain relief head screwdriver Wire nuts Masking tape Gloves Spirit level Knife Wire cutter/stripper Hammer Flat blade screwdriver Saw, jig saw or 8″...
Page 8
NOTE: Measure installation height from the cooking surface to the outer glass portion of the hood. ″ ′ ″ ′ ′ ″ ′ ″ ′ ″ ′ ″ ′ ″ ′ ″ ′ ″ ′ ″ 24” Min. ′ ″ 30”...
Page 9
HARDWARE PACKAGE Locate and count screws 3 wall fasteners 3 wood screws 12 hood attachment 2 thumb screws screws Drill 2 (two) 3/16″ pilot holes through studs or rear wall support 14-5/8″ to top of bracket REAR WALL MOUNTING TEMPLATE ALIGN BOTTOM EDGE WITH PENCIL LINE, INDICATING BOTTOM...
Page 10
″ 5-1/2” centerline to wall FOR CEILING VENT DUCTING 8-1/2” dia. hole FOR WALL VENT DUCT ″ ″ ″ ″ ″ Ceiling Centerline 26” above the marked bottom pencil line for installation height. ″ ″ 8" Min. Opening for Ductwork 8-1/2”...
Page 11
″ ″ Drill 2 (two) 3/16″ pilot holes through studs or rear wall support ″ 14-5/8″ to top of bracket REAR WALL MOUNTING TEMPLATE ALIGN BOTTOM EDGE WITH PENCIL LINE, INDICATING BOTTOM OF THE HOOD 49-80405 04-06 JR...
Page 12
Front side Bottom view Rear mounting Rear side hooks Rear view Engage flange on motor housing into slots To Lights Control Panel...
Page 13
Airflow Duct tape over seam and screw Screw Levelers Screw hole ″...
Page 14
Knockout J-Box cover House wiring J-Box cover...
Page 15
Mounting screws Duct cover support bracket Upper duct cover Lower duct cover Lower duct cover seat NOTE: The charcoal filter is not required for this installation. Duct cover support bracket Filter Lock...
Page 16
″ Ceiling ″ ″ 8" Min. Opening for Ductwork View from rear View From Rear cleats Cleats 1” x 6” min. 1" x 6" Min. mounting Mounting support Support Centerline of Centerline of installation Installation Space space ″ ″...
Page 17
″ ″ Drill 2 (two) 3/16″ pilot holes through studs or rear wall support ″ 14-5/8″ to top of bracket REAR WALL MOUNTING TEMPLATE ALIGN BOTTOM EDGE WITH PENCIL LINE, INDICATING BOTTOM OF THE HOOD 49-80405 04-06 JR...
Page 18
Rear mounting hooks Rear view Engage flange on motor housing into slots Levelers Front side Bottom view Rear side To Lights Control Panel Screw hole ″...