Software Control - Bosch 700 Series Information

6 | AUTODOME 700 Series IP PTZ Camera
Protection on Power Peak current 21.4 A, peak power 1500 W
Output (Arm Power (10/1000 μs)
Supply)
10/100 Ethernet Peak current 14 A, peak power 200 W
Data Lines (8/20 μs)

Software Control

Camera Setup/Control Via Internet Explorer Web browser version
7.0 or later, Bosch Configuration Manager
or BVMS
Software Update Firmware upload
Network
Standards H.264 (ISO/IEC 14496‑10), M‑JPEG, JPEG
Streaming A total of four (4) independent streams:
• Two (2) individually configurable H.
• One (1) H.264, I-frame only stream
• One (1) M‑JPEG stream at 4CIF/D1
GOP Structure IP, IBP, IBBP
Data Rate 9.6 kbps to 6 Mbps
Overall IP Delay 240 ms
Resolution (Horizontal x Vertical, PAL/NTSC)
• 4CIF/D1 704 x 576/480 (50/60 ips
• CIF 352 x 288/240 (50/60 ips
4. Depending on picture content and movement
Ethernet 10-Base T/100 Base-TX, auto-sensing, half/
full duplex, RJ45
Protocols RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS,
FTP, DHCP, IGMP V2/V3, ICMP, ARP, SMTP,
SNTP, SNMP v3, RTSP, 802.1x, iSCSI,
DynDNS, UPnP, IP v4/6, QoS, SSH, SSL
Audio
• Standard G.711, 8 kHz sampling rate
L16, 16 kHz sampling rate
• Signal-to- >50 dB
Noise Ratio
• Audio Full Duplex / Half Duplex
Streaming
Fiber Optic Kit
VG4-SFPSCKT
Description Fiber Optic Ethernet Media Converter kit
Requires a small form-factor pluggable (SFP)
module (sold separately).
Data Interface Ethernet
Data Rate 10/100 Mbps
IEEE 802.3 Compliant
264 streams at 4CIF/D1 resolution,
(suitable for recording)
resolution
)
4
)
4
5
Compatible Receiver
Installation
5. Kit available separately and must be installed inside the AutoDome power supply box.
SFP Modules
Description
Data Interface
Data Rate
Mechanical
Dimensions (LxWxH)
• SFP-2 and SFP-3
• SFP-25, SFP-26
Weight (all SFP modules)
Type
SFP-2 MMF
SFP-3 SMF
SFP-25 MMF
SFP-26 MMF
Fiber Compatibility
Optical Fiber Compatibility,
MMF
Optical Fiber Compatibility,
SMF
Optical Distance
Specifications
.
Miscellaneous
Sectors/Titling
Masking
Full Duplex or Half Duplex Electrical Port
Full Duplex Optical Port
CNFE2MC
Installed inside a VG4-A-PA0, VG4-A-PA1,
VG4-A-PA2, VG4‑A‑PSU1, or a VG4‑A‑PSU2
power supply box with supplied mounting
hardware
Interchangeable modules available for use
with MMF or SMF optical fiber.
Ethernet
10/100 Mbps
IEEE 802.3 Compliant
55.5 x 13.5 x 8.5 mm (2.2 x 0.5 x 0.3 in.)
63.8 x 13.5 x 8.5 mm (2.5 x 0.5 x 0.3 in.)
0.23 kg (.05 lb)
Connec Wavelength
tor (transmit/receive)
Duplex 1310 nm /
LC 1310 nm
Duplex 1310 nm /
LC 1310 nm
Single 1310 nm /
SC 1550 nm
Single 1550 nm /
SC 1310 nm
50/125 µm MMF. For 50/125 µm
fiber, subtract 4 dB from the specified
optical budget value. Must meet or
exceed fiber standard ITU-T G.651.
8–10/125 µm SMF. Must meet or
exceed fiber standard ITU-T G.652.
Specified transmission distances are
limited to the optical loss of the fiber
and any additional loss introduced by
connectors, splices, and patch panels.
The modules are designed to operate
over the entire optical loss budget
range, so they do not require a
minimum loss in order to operate.
16 independent sectors with a 20-character
title/sector
24 individually configurable privacy masks
Max.
Distance
2 km
(1.2 miles)
20 km
(12.4 miles)
2 km
(1.2 miles)
2 km
(1.2 miles)