Electrical Safety - Sun joe CJ601E Operator's Manual

• LIGHTING – Only operate your garden shredder in daylight
or good artificial light.
• DON'T OVERREACH – Keep proper footing and balance
at all times. Wear oil resistant rubber soled footwear.
• Never leave a running tool unattended. Turn the garden
shredder off and wait until it comes to a complete stop
before leaving the work area.
• Avoid accidental start-ups. Make sure switch is in off posi-
tion before plugging in the power cord.
• USE RIGHT APPLIANCE – Do not use this product for any
job except that for which it is intended.
• KEEP CHILDREN AWAY – All visitors, children and pets
should stay at a safe distance from the work area.
m
WARNING:
Some dust and debris created by
the use of this tool could contain chemicals known to the
State of California to cause cancer and birth defects or other
reproductive harm.
Some examples of these chemicals are:
- chemicals in fertilizers
- compounds in insecticides, herbicides and pesticides
- arsenic and chromium from chemically treated lumber
Your risk from exposure to these chemicals varies depending
on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved
safety equipment, such as dust masks that are specifically
designed to filter out microscopic particles.
m
WARNING:
The wires of this product could
contain chemicals know to the State of California to cause
cancer and birth defects or reproductive harm. Wash hands
after handling.

Electrical Safety

1. Always check that the power supply corresponds to the
voltage on the rating plate.
2. Do not operate in an area where there is a possibility
of body contact with grounded items (i.e.: pipes, metal
structures). Avoid contact with metal objects.
3. Do not pull/yank the power cord. Keep the power cord
away from hot surfaces and sharp objects.
4. Always use a grounded three-wire extension cord and re-
ceptacle that are made of rubber and intended for outdoor
use. The machine is designed to operate on 120 Volt AC
household current. The chipper power cord has a ground-
ing prong. To avoid the possibility of shock it must always
be used with a properly grounded three-prong receptacle
protected with a 20A fuse. Never remove the ground prong
from the plug.
GROUNDING
PIN
(A)
ADAPTER
(C)
GROUNDING
MEANS
AA210
GROUNDING METHOD
Note: If necessary, the machine can be switched to a
single-phase network (120V/60Hz). Connect the main
leads to a standard 120V/60Hz electrical supply which has
protection devices of under-voltage, over-voltage, over-
current as well as a residual current device (RCD) with a
maximum residual current rated at 30mA. Only a qualified
electrician should only do this.
5. Do not operate the machine where water is present
(i.e.: rain, sprinkler, puddles).
6. Do not touch electrical plugs with wet hands.
7. Keep the extension cord away from the moving parts and
hot motor housing.
8. Immediately replace and dispose of damaged wires and
plugs.
9. Do not open the switch box on the motor. If service is
necessary take the machine to a qualified electrician.
10. Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for the
gardening appliance. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
11. Warning – Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Exception: Types SW, SOW, STW, STOW, SJW, SJOW,
SJTW, and SJTOW are alternative designations to Types
SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJOW-A,
SJTW-A, and SJTOW-A, respectfully.
12. Extension Cord – Make sure your extension cord is in
good condition. When using an extension cord, be sure to
use one heavy enough to carry the current your product
2
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
(B)
GROUNDING
PIN
(D)