Pioneer CNDV-50MT Operation Manual page 123

MAN-CNDV-50MT-EN.book Page 121 Wednesday, May 4, 2005 1:49 PM
Message
Direction of G sensor is not correct.
Please turn system power off and
check the installation. After
checking, please re-boot the system
and press "OK".
Gyro Sensor is not working properly.
Please consult your dealer or Pioneer
service centre.
This function is not available now.
System detected that the vertical
angle of the installation has been
changed. Learning status for Gyro
Sensor has been initialised.
System detected that the vertical
angle of the installation exceeds the
permission level. Please install the
navigation unit correctly.
Route calculation was not possible.
Route calculation was not possible
because the destination is too far.
Route calculation was not possible
because the destination is too near.
Route calculation was not possible
due to traffic regulations.
Route calculation was not possible
because no guidance can be
provided around the destination or
the starting point.
There is no route to the destination.
Your journey can not avoid the
specified area.
The route could not avoid the
specified area.
Toll road has not been avoided.
Ferry has not been avoided.
When
Direction of G sensor is set
incorrectly.
Abnormal output of Gyrosensor is
detected.
The screen cannot be displayed with
Vehicle Dynamics Display.
Because the sensor has not been
taught so the sensor information
cannot be acquired.
If the mounting angle of the Hide-
away unit has been changed.
The navigation unit is installed with
an extreme angle exceeding the
limitation of the installation angle.
Route calculation has failed because
of malfunction of map data, software,
hardware, or disc.
The destination is too far.
The destination or way point(s) is too
close.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a
Control Traffic Zone (CTR) and the
route calculation is hampered.
The destination, way point(s), or
starting point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
The destination or way point(s) are in
an isolated island, etc. without a ferry
and the route calculation is
impossible.
If route setting cannot avoid
specified Areas to Avoid.
If the route to the destination (or way
point) cannot be established by
bypassing toll roads (including toll
areas) and Areas to Avoid.
In case a ferry route was included in
the route to the destination or way
points even though "Avoid Ferry"
was set to On.
What to do
See the "Installation Manual" and set
the direction of the Hide-away unit
correctly.
Note down the error code shown on
the screen; turn off the power, and
then contact your nearest Pioneer
service facility.
If the sensor learning status reaches
the Sensor Initialising status or
more, the system is ready to be used.
The system initialises the sensor in
order to operate it with the maximum
performance and automatically
starts re-learning.
Confirm the installation angle. (The
navigation system must be installed
within +30 degrees to –30 degrees of
the horizontal, or within five degrees
of your vehicle's direction of travel.)
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
• Set a destination closer to the
starting point.
• Set one or more way points.
Set a destination [and way point(s)]
farther from the starting point.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try the destination or way point(s)
away from the currently set points to
some extent.
• Drive your vehicle to an
unrestricted area and reset the
destination and way point(s).
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
Change the destination.
If the current route is not desired, set
destination or way points that do not
pass through the Areas to Avoid.
If the current route is not desired, set
destination or way points that do not
pass through toll roads (including
toll areas) and Areas to Avoid.
If the current route is not desired, set
destination or way points that do not
pass through a ferry route.
121