GE Profile PT920 Brochure page 24

27" built-in single ovens
27"/24" built-in single oven dimensions (in inches)
27" models PK916, JKP70, JKP30, JKS10
10
Locate
junction box
either 5" MIN.
below cutout
floor or 44"
MIN. above
cutout floor
D
Minimum
cutout location
32-1/2
from floor
(Minimum 15-5/8"
from floor when 2" x 4"
installed below built-in
or equiv.
microwave oven)
runners
Note: These ovens are not approved for stackable or side-by-side installations.
Note: Door handle protrudes 3" from door face. Cabinets and drawers on adjacent
45° and 90° walls should be placed to avoid interference with the handle.
Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at
least a 194°F temperature rating.
Note: For 27" built-in single ovens, if marks, blemishes or the cutout opening is
visible above the installed oven, it may be necessary to add wood shims under the
runners and front trim until the marks or openings are covered.
Undercounter installation dimensions (in inches)
Models PK916, JKP70, JKP30 and JKS10
Gas or electric cooktops may be installed over this
oven. See cooktop installation instructions for cutout size.
See label on top of oven for approved cooktop models.
240V / 208V
Junction Box
25
Location
25" MIN.
25 1/4" MAX.
27 5/8" MIN.
28 1/8" MAX.
3/4" Support
Platform Required
Must Support 150 Lbs.
Electric wall ovens are not approved for installation with a plug and receptacle.
They must be hard wired in accordance with installation instructions.
Note: Oven is rated for use only under 30" standard or sealed burner gas and
selected 30" CleanDesign and Calrod ®
Installation information: Before installing, consult installation instructions
packed with product for current dimensional data.
(continued)
A
Allow 3/4"
for overlap
over all edges
of cutout
B MIN.
F
E
C MIN.
Conduit 48-1/2" long
Gas or electric connections
for gas cooktop must be
located in an adjacent
accessible location to the right
5
Allow 1"
22" MIN.
unit overlap
Above
all edges
Support
Platform
24
Note: 36" ribbon cooktops are approved for use over
GE 30" single wall ovens* and warming drawers. 30"
ribbon cooktops are approved for use over GE 30"
and GE 27" single wall ovens* and warming drawers.
Refer to cooktop and wall oven installation information
packed with products for current dimensional data.
*Except wall ovens with Trivection
electric cooktops.
Oven support
for 27" models
G
Oven support
for 24" models
Cabinet
A – Cabinet width required
B – Minimum cabinet depth
C – Opening width
D – Opening height
Oven
E – Overall depth*
F – Overall height with trim
G – Overall width
* Depth including door handle is approximately 26-7/8" min to
26-8/10" max. 26-5/8" on models PK916, JKP70/30 and JKS10.
Sealed burner gas cooktop
installation dimensions (in inches)
90° Street el
36"
Typical
Countertop
Height
Standard burner gas cooktop
installation dimensions (in inches)
90° Street el
®
technology.
Note: Cabinets installed adjacent to wall ovens must have
an adhesion spec of at least a 194°F temperature rating.
C L
Suitable
bracing
to support
18"
runners
Over centerline
of cabinet
(Must support 275 lbs.)
C L
11"
over centerline
of cabinet
(Must support 275 lbs.)
PK916, JKP70/30, JKS10
27" min.
23-5/8"
25" min. - 25-1/4" max.
27-5/8" min. - 28-1/8" max.
23-5/8"
w/o trim 29"
29-7/8" - 30-3/4"
26-5/8"
5" To center of 2" diameter
hole from countertop
2" Diameter hole (20-7/8"
45° Elbow
from front of countertop
to hole center)
Cabinet sides
3-7/16" To center of 2" diameter
hole from countertop
2" MIN. diameter hole
(23-1/4" from front
45° Elbow
surface of countertop)
Cabinet sides
ge.com
2" x 4" or
equivalent
runners
2 x 4 or
equivalent
runners