Only use attachments specified by the manufacturer. The cards contain no user serviceable parts: only refer to authorized, qualified service personnel for any servicing. Your warranty will be voided if you tamper with the internal components. YG2 / YS2 2 / 2 Rev. 1.1...
F, ensure proper ventilation ° ° ° ° Storage temperature: -20 C …60 C • -4 F …140 Power Supply The console in which the card is mounted provides power supply and grounding. YG2 / YS2 3 / 3 Rev. 1.1...
Page 4
The cards may not be serviced, altered or modified without authorization of Optocore or an Optocore authorized dealer / distributor. Qualified service personnel may only carry out repair and maintenance work.
CE-Conformity This document confirms that the product YG2 and YS2 bearing the CE (Communauté Européenne) label meets all requirements in the EMC directive 2004/108/EG laid down by the Member States Council for adjustment of legal requirements. Furthermore the product complies with the rules and regulations of the low-voltage directive 2006/95/EG.
YG2 / YS2 Optical Digital Mini - YGDAI Cards for Yamaha Devices Table of Contents Important Safety Instructions ...........................2 Purchaser Information .............................3 CE-Conformity..............................5 Eye Safety ...............................5 Device Description ............................7 Front Panel YG2..............................8 YG2 Cards Details ............................9 Digital Audio ............................9 LC-Connectors............................9 HA Remote ............................9...
Yamaha consoles and devices such as the PM or DM series devices. YG2 / YS2 cards offer a broad flexibility in all sorts of temporary and permanent applications, especially when long distance connections, high-quality audio transmission, extremely low latency or high security is required.
2 x RS422 ports e.g. for Yamaha HA Remote protocol exchange with console Use the TRI-Y cable, provided with the YG2 card. See chapter “Connection Tables” for detailed pin out. For updating via PC a standard RS232 cable is sufficient.
HA Remote The YG2 card supports direct pick up of HA Remote signals from the console slot e.g. provided in Yamaha LS9 series. If the console does not provide the HA Remote signal on the console slot, the signal can be applied externally to the USB/RS232/REMOTE port.
MAIN Port The MAIN port is connected to the SUB port of an YG2 card. In a chain of several YS2 cards it is connected to the SUB port of the next YS2 card towards direction of the YG2 card.
Hardware Connection To get the YG2 / YS2 card system going, please be sure that the main power of the console is turned off before inserting the cards into the Mini - YGDAI slots. Please refer to your consoles manual for detailed information.
Page 12
“Optocore Ethernet transport” and “Enable local Ethernet”. SUB Setup -> SUB Cards: Set the number of YS2 cards, you have connected to your YG2 card. Push button “Write” first, confirm with “OK” and press “Close” to exit the dialog.
YG2 card into Yamaha Emulation Mode (YEM) using OPTOCORE CONTROL. Fig. 2: Wiring of a system with DD32(E), X6-converter units and a Yamaha console with YG2/YS2 cards. In order to control the X6-converter at the console the Yamaha Emulation Mode (YEM) must be activated in OPTOCORE CONTROL.
The table below lists Yamaha consoles and devices by the number of IN / OUT audio channels supported on one console slot. Set the YG2 / YS2 cards either to “MY-16AT emulation” or “MY-8AT emulation” according to the number of channels supported.
The TRI-Y cable combines the two RS422 and the USB-Port for PC connection in one D-Sub-9 connector. It is used to establish the connection from the YG2-Card to a PC USB interface and remote interface of a console. YG2 Auxiliary Port 2 x RS422 and USB port...
Convention EIA / TIA - 232 Data channels Digital control data R x D, T x D Data rate 57 600 Baud SUB Port Convention Optocore 64 channel CAT5 Cable Type ANSI/TIA/EIA-568-A, TSB-95 CAT5 Max. Cable length 10 m / 33 feet USB Port Remote control connection USB 1.1 full speed...
Dimensions and Weight Cards Dimensions YG2 / YS2 Card H x B x T: 100 x 160 x 40 [mm] H x W x D: 3.94 x 6.3 x 1.57 [inch] Cards Weight YG2 Card Weight: 365 g / 12.88 ounces YS2 Card Weight: 175 g / 6.17 ounces...
Declaration of Liability Optocore accepts no liability for damage caused to other devices through operation of the YG2 / YS2 cards. Optocore is not liable for any damage caused by shipping accidents, misuse, abuse, operation with incorrect voltage, operation with faulty peripheral equipment, or improper or careless installation of the cards.