Download
Share
Print this page
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Door
  5. 19217
  6. Installation instructions

GE 19217 Installation Instructions

General electric wired chime kit installation instructions.
Hide thumbs
   
1
2

Advertisement

Wired Chime Kit
Installation Instructions for Wired Door Kit
Included hardware:
1: Chime
2: (2) Push buttons
3: Transformer
Included Hardware:
(4) Plastic screw anchors
(4) 4x25mm screws (for anchors)
(4) 3x20mm screws
(3) Wire nuts
Required Tools:
Wire stripper/cutter, small flat blade screwdriver, Phillips screwdriver, drill,
and drill bit (1/16" and 5/32")
Chime Tune Setting
1. Remove the chime cover and locate the two 3 position dip switches shown
below.
2. Select the desired chime sound from the table below.
Chime Sound Table
Position
1
2
3
Westminster
OFF
OFF
ON
Ding Dong
OFF
ON
OFF
Knock
ON
OFF
OFF
Bronze Chime
OFF
ON
ON
Cuckoo Clock
ON
OFF
ON
Foghorn
ON
ON
OFF
Gong
ON
ON
ON
New Installation Instructions
Use the proper type of wire for your application, in accordance with local
electrical codes. If you are unsure of the requirements consult a licensed
electrician.
1. Shut off power at fuse box or circuit breaker
2. Locate and mount the included power transformer in a dry location.
3. Connect the house power to the transformer input as shown in the
schematic.
a. House Black to Transformer Black
b. House White to Transformer White
c. House Green to Transformer Green
4. Locate the mounting location for the chime.
a. Remove the cover for the chime.
b. Pull the wires through the slot in base of chime.
GE Model 19217
c. Mark the 4 holes using the base as a template with the arrow pointing up.
www.jascoproducts.com
d. If mounting in sheetrock wall, drill 5/32" holes and insert the plastic
screw anchors, otherwise drill pilot hole for screw.
e. Mount the chime base using the 4x25mm screws.
f. Attach the wires for the pushbuttons as shown in the schematic.
g. Put the cover on the chime
5. Mount the pushbuttons.
a. Locate the mounting location and pull the wires through the slot in the
pushbutton.
b. Remove the pushbutton cover.
c. Use the base as a template and mark the mounting holes with the arrow
pointing up.
d. Drill pilot holes using a 1/16" drill.
e. Connect the wires matching the schematic.
f. Put the cover on the pushbutton.
g. Replace the pushbutton cover.
6. Reapply power and test the chime.
Replacement Installation
1. Shut off power at fuse box or circuit breaker.
2. Remove the cover from the old door chime and disconnect wires from screw
terminals and label them for reference.
3. Install new chime
a. Remove the cover for the chime.
b. Pull the wires through the slot in base of chime.
c. Mark the 4 holes using the base as a template with the arrow pointing up.
d. If mounting in sheetrock wall, drill 5/32" holes and insert the plastic
screw anchors, otherwise drill pilot hole for screw.
e. Mount the chime base using the 4x25mm screws.
f. Attach the wires for the pushbuttons as shown in the schematic.
g. Put the cover on the chime.
Removal and Replacement of Push button cover
For technical support contact Jasco Products Company at 1-800-654-8483
or www.jascoproducts.com
Made in China
Hecho en China
is a trademark of
General Electric Company
and is used under license to
Jasco Products Company LLC,
10 E. Memorial Road,
Oklahoma City, OK 73114.
www.jascoproducts.com
19217
Rev. 3-07

Advertisement

   Related Manuals for GE 19217

   Summary of Contents for GE 19217

  • Page 1

    6. Reapply power and test the chime. Replacement Installation 1. Shut off power at fuse box or circuit breaker. 2. Remove the cover from the old door chime and disconnect wires from screw terminals and label them for reference. 3. Install new chime a.

  • Page 2

    Modelo GE 19217 www.jascoproducts.com Equipo alambrado de timbre para puertas Instrucciones de instalación para el Equipo alambrado de timbre para puertas Equipo incluido: 1: Timbre 2: (2) Botones de timbre 3: Transformador Equipo incluido: (4) Anclajes de plástico para tornillos...

Comments to this Manuals

Symbols: 0
Latest comments: