Download Print this page

Advertisement

Y72599100700
®
EPSON
SCSI Hard Disk Drive
SCSI Festplattenlaufwerk
Le disque dur SCSI
Drive per disco Fisso SCSI
Unidad de disco duro con SCSI

Advertisement

   Related Manuals for Epson SCSI Hard Disk Drive

   Summary of Contents for Epson SCSI Hard Disk Drive

  • Page 1

    ® EPSON SCSI Hard Disk Drive SCSI Festplattenlaufwerk Le disque dur SCSI Drive per disco Fisso SCSI Unidad de disco duro con SCSI Y72599100700...

  • Page 2

    Trademark Acknowledgements EPSON is a registered trademark of Seiko Epson Corporation Notice All rights reserved. Reproduction of any part of this manual in any form whatsoever without Epson’s express written permission is forbidden. The contents of this manual are subject to change without notice.

  • Page 3

    Introduction ® The Epson 34OMB SCSI hard disk drive is a high capacity, high performance, random access storage device designed to be installed in your EISA Series (desktop or tower) computer. This manual provides information you need to know to install the SCSI hard disk drive in your computer, and lists the technical specifications for the drive.

  • Page 4

    User’s Guide to install a disk drive. Also see your SCSI Adapter Card User’s Guide for details on installing an internal SCSI device. As you install the SCSI hard disk drive, refer to the illustration on the following page to identify the different parts.

  • Page 6

    Before installing the SCSI hard disk drive, need to check the jumper settings on the drive. The jumpers determine the following settings: H SCSI ID of the drive (J6) Parity checking (J6) Drive power-up (J6) SCSI bus signals (J7) Terminator power (J8).

  • Page 7

    S C S I I D s e l e c t i o n Pins l-2, 3-4, and 5-6 of jumper J6 determine the SCSI ID as shown in the table below. 1 SCSI ID 1 Pins 1-2 1 Pins 3-4 1 Pins 5-6 1 X = Jumper installed 0 = No jumper * = Factory setting...

  • Page 8

    Pins 7-8 on jumper J6 control odd checking by the drive as parity table below. shown in the Pins 7-8 X = Jumper installed 0 = No jumper * = Factory setting Set J6 to enabled if the devices connected to the adapter card SCSI support parity checking.

  • Page 9

    SCSI devices in between must not be terminated. If you install the SCSI hard disk drive in the middle of the SCSI interface, you must remove all three terminator resistors on the drive. When replacing the resistors, make sure pin 1 is aligned correctly.

  • Page 10: Performance Specifications

    Technical Specificafions Performance Specifications Capacity unformatted per drive: 402MB per surface: 57.4MB Capacity formatted per drive: 340,558,848 bytes per surface: 48,651,264 bytes Average latency: 8.3 msec Seek time single track read: 2.5 msec single track write: 3.0 msec average read: 15 msec average write: 15 msec...

  • Page 11: Environmental Specifications

    Environmental Specifications Ambient temperature operating: 41’ to 122O F (5O to 50” C) nonoperating: -40’ to 149’ F (-40” to 65’ C) Relative humidity operating: 5 to 80% noncondensing nonoperating: 5 to 80% noncondensing Elevation: -1,000 ft. to 10,000 ft. Vibration, all axes operating: 0.5G...

  • Page 12

    EPSON Printed in USA 91.8~2 (CT-01)

Comments to this Manuals

Symbols: 0
Latest comments: