GE DECT 00028056 Quick Setup Manual

Model 28166
DECT 6.0 Two-Line 2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company
shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is
Cordless Handset
not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue
service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you
of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your
quick Set-Up Guide
right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and
Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures
where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If
these changes are expected to affect the use or performance of your telephone equipment, the telephone company
must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
Interference Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference; and (2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is "receiving" the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving
antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving
antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet,
"How To Identify and Resolve Radio/TV Interference Problems." This booklet is available from the U.S. Government
Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies.
for use with Model 28165 Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Equipment Approval Information
Hearing Aid Compatibility (HAC)
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance
This telephone system meets FCC standards for Hearing Aid Compatibility.
with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment
Licensing
published by ACTA.
1 Notification to the Local Telephone Company
Licensed under US Patent 6,427,009.
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer
FCC RF Radiation Exposure Statement
Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone
company.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and
these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices
your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as
For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with
determined by the REN, you should contact your local telephone company.
the belt clip supplied with this product. Use of other accessories may not ensure compliance with FCC RF exposure
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
guidelines.
applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug
Information for DECT Product
is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
This telephone is compliant with the DECT 6.0 standard which operates in the 1.92GHz to 1.93GHz
Notes
frequency range.
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if
you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this
product does not disable your alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
visit the GE website at: www.GE.com/phones
Thomson Inc.
101 West 103rd Street
Model 28166 Indianapolis, IN 46290-1102
00028056 (DOM E) © 2008 Thomson Inc.
08-30 Trademark(s) ® Registered
Marca(s) Registrada(s)
Printed in China
US Number is located on the cabinet bottom. Introduction
REN Number is located on the cabinet bottom.
CAUTION: When using telephone equipment, there are basic safety instructions
that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS
provided with this product and save them for future reference.
IMPORTANT: Because cordless phones operate on electricity, you should have at
least one phone in your home that isn't cordless, in case the power in your home
goes out.
If you have purchased an extra handset apart from your original purchased unit you
may find a detailed description of its functions in the User's Guide provided with
your original purchased unit.
If you have purchased an extra handset that is not of the same type as your
original handset you may still use the original User's Guide to help explain the new
handsets basic functions and options.
Parts Checklist
Make sure your package includes the items shown here.
Battery
compartment
Charge
cover
Cradle
Installing the Handset Battery
NOTE: You must connect the handset battery before use.
CAUTION: To reduce the risk of fire or personal injury, use only the Thomson
Inc. approved Nickel Metal Hydride (Ni-MH) battery model 5-2721, which is
compatible with this unit.
1. Locate battery and battery door which are packaged together inside a plastic bag and are separate
from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: To ensure proper battery installation, the connector is keyed and can be
inserted only one way.
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handset in the base to charge.
Extra Charging Cradle
1. Plug the AC power converter of the extra charging cradle into the electrical outlet.
NOTE: This power adaptor is intended to be correctly orientated in a vertical or
floor mount position.
2. Place the handset in the extra charging cradle. The charge indicator turns on, verifying the battery is
charging.
3. Allow the phone to charge for 16 hours prior to first use.
Registration
YOU MUST REGISTER THE HANDSET TO THE MAIN BASE BEFORE USE!
After the optional handset has charged for 16 hours on the extra charger, the screen displays PLEASE
REGISTER
.
1. Make sure your phone is OFF (not in TALK mode).
2. Press the MENU (SKR) to go to the main menu.
3. Use the 5 or 6 buttons to scroll to REGISTRATION.
4. Press the SELECT (SKL) to confirm. The screen displays, PRESS INTERCOM ON BASE FOR 5S THEN
PRESS OK.
5. Press and hold the INTERCOM/PAGE button on base unit until the charge/in use indicator flashes, then
press handset OK (SKL). The screen displays, PLEASE WAIT, REGISTING. The handset screen displays,
HANDSET X REGISTERED, where X is the handset number. You will hear a confirmation tone.
If handset displays PLEASE REGISTER, press the OK (SKL) on the handset and repeat step 5 above.
Naming the Handset
1. Make sure your phone is OFF (not in TALK mode).
2. Press the MENU (SKL) to go to the main menu.
3. Use the 5 or 6 buttons to scroll to HANDSET NAME.
4. Press the SELECT (SKL) to enter the menu.
5. Use the touch-tone pad to enter a name (up to 12 characters).
NOTE: If you make a mistake, press the DELETE (SKL) to backspace and delete one
character at a time.
6. Press the DONE (SKL) to save.
Global De-registration
Follow the steps below to de-register all handsets at the same time.
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that handset's
telephone features cannot be used until the handset is re-registered.
1. Press and hold the INTERCOM/PAGE button on the base until the charge/in use indicator on the base
flashes.
2. Press and hold the INTERCOM/PAGE button on the base again until the charge/in use indicator on the
base flashes rapidly.
3. Press and release the INTERCOM/PAGE button on the base once. All handsets are de-registered and
Belt PLEASE REGISTER shows in the display.
Handset
clip Intercom Operation
battery pack
Handset (applicable only with additional handsets)
The intercom feature allows you to have a conversation with another registered handset without tying
up the telephone line, allowing you to still receive incoming calls.
Making an Intercom Call
1. Make sure the handset is OFF (not in TALK mode).
2. Press the int button on the handset.
3. The screen displays a list of registered handsets. Use the 5 or 6 button to scroll to the desired handset
or base you wish to page.
4. Press the SELECT (SKL).
NOTE: To cancel page, press the int button again or the END/CANCEL button on the
sending handset.
5. Wait for the person at the receiving unit to press the OK (SKL) or the int button.
NOTE: If the receiving unit does not answer within two minutes, the intercom call is
automatically canceled. The originating handset displays NO ANSWER.
6. When finished, press the END/CANCEL button or int button on either handset or unit to deactivate the
intercom.
NOTE: The system is expandable up to 6 handsets (by purchase of optional Model
28166 handset with recharge cradle). When 4 handsets are registered, the system
can handle 2 separate intercom operations at once, for example, 1st handset
intercoms with 2nd handset while 3rd handset intercoms with 4th handset.
Receiving an Intercom Call
When you receive an intercom call, your handset beeps. To answer the call press the int button or the OK
(SKL).
Advanced Intercom Features
Receiving an Incoming Call During an Intercom Call
If you receive a telephone call during an intercom call, both handsets or base will emit an alert tone and
remain in intercom mode. Either handset or base user may press the LINE 1, LINE 2 or the handsfree
button to answer the call.
Using Intercom with External Telephone Calls
During a telephone call, you may use the intercom/paging function to;
• page another handset or base and have an off line, private (two-way) intercom conversation,
• have a three-way conversation between the external caller and the handsets or base,
• transfer the external telephone call to another handset or base.
1. During an external call, press the int button to put the external line on hold.
2. A list of registered handsets and base shows on the display. Use the 5 or 6 button to scroll to the
desired handset or base you want to page.
3. Press SELECT (SKL) to page.
4. The receiving handset or base is paged.
5. Press the int button on the receiving handset or base to answer the intercom call.
6. When the receiving handset connects; Limited Warranty
a) You may have an off line, private (two-way) intercom conversation, the external caller will not hear
What your warranty covers:
the conversation.
• Defects in materials or workmanship.
b) Press the UNHOLD (SKL) on the originating handset to have a three-way conversation with the
For how long after your purchase:
receiving handset and the external caller. The screen on the originating and receiving unit displays
• One year, from date of purchase.
CONFERENCE.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to
NOTE: A handset can enter conference mode directly by pressing LINE 1, LINE 2
the rental firm, whichever comes first.)
button on the second handset during a call.
What we will do:
7. When finished, press the END/CANCEL button or int button to end the intercom call, return to the talk
• Provide you with a new unit. The exchange unit is under warranty for the remainder of the original
mode, and resume your original telephone conversation, or press the END/ button on the
CANCEL
product's warranty period.
originating handset or base to transfer the call to the second handset and then end the call on the
How you get service:
originating handset.
• Properly pack your unit. Include any cables, etc., which were originally provided with the product. We
NOTE: If the receiving handset does not answer within 30 seconds, the originating
recommend using the original carton and packing materials.
handset rings back and displays CALLBACK. If the originating handset does not
• "Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
answer within 20 seconds, the call is automatically dropped.
is within the warranty period, must be presented to obtain warranty service." For rental firms, proof
Three-way Conference between a Handset or Base and
of first rental is also required. Also print your name and address and a description of the defect.
External Calls on the Line 1 and Line 2
Send via standard UPS or its equivalent to:
Thomson Inc.
1. During an external call on either Line 1 or Line 2, press the HOLD (SKL) to put the call on hold.
11721 B Alameda Ave.
2. If the originating line is Line 1, press the LINE 2 button. Line 1 icon flashes and Line 2 icon repeatedly
Socorro, Texas 79927
flashes in the display.
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of damage or loss.
3. Press the CONF (SKL) to conference with the external call.
• A new unit will be shipped to you freight prepaid.
Battery Safety Precautions
What your warranty does not cover:
• Customer instruction. (Your Owner's Manual provides information regarding operating instructions
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, toxic materials could
and user controls. Any additional information, should be obtained from your dealer.)
be released which can cause injury.
• Installation and setup service adjustments.
• To reduce the risk of fire or personal injury, use only the Nickel Metal Hydride (Ni-MH) battery listed
in the User's Guide. • Batteries.
• Keep batteries out of the reach of children. • Damage from misuse or neglect.
• Remove batteries if storing over 30 days • Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
NOTE: The RBRC seal on the battery used in your Thomson Inc. product
• Acts of nature, such as but not limited to lightning damage.
indicates that we are participating in a program to collect and recycle the
Product Registration:
rechargeable battery (or batteries).
• Please register your product on-line at www.ge.com/phones. You may also complete and mail the
For more information go to the RBRC web site at www.rbrc.org
Product Registration Card if one was received with your unit. Product Registration will make it easier
or call 1-800-8-BATTERY or contact a local recycling center. to contact you should it ever be necessary. Registration is not required for warranty coverage.
Limitation of Warranty:
Warranty Assistance
• THE WARRANTY STATED ABOvE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT.
ALL OTHER WARRANTIES, ExPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
If trouble is experienced with this equipment, for warranty information, please contact customer service
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
at 1-800-448-0329. If the equipment is causing harm to the telephone network, the telephone company
vERBAL OR WRITTEN INFORMATION GIvEN BY THOMSON INC., ITS AGENTS, OR EMPLOYEES SHALL
may require that you disconnect the equipment until the problem is resolved. CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
Any unauthorized repairs, changes or modifications not expressly approved by Thomson Inc. could void
• REPAIR OR REPLACEMENT AS PROvIDED UNDER THIS WARRANTY IS THE ExCLUSIvE REMEDY OF
the user's authority to operate this product. For instructions on how to obtain a replacement unit, refer THE CONSUMER. THOMSON INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEqUENTIAL
to the warranty included in this guide or call customer service at DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
1-800-448-0329. ANY ExPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES
AND LIMITED WARRANTY ARE GOvERNED BY THE LAWS OF THE STATE OF INDIANA. ExCEPT TO
Or refer inquiries to:
THE ExTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY
Thomson Inc.
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE
Manager, Consumer Relations
WARRANTY PERIOD SET FORTH ABOvE.
P O Box 1976
How state law relates to this warranty:
Indianapolis, IN 46206
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
Attach your sales receipt to this booklet for future reference or jot down the date this product was
limitations on how long an implied warranty lasts so the above limitations or exclusions may not
purchased or received as a gift. This information will be valuable if service should be required during the
apply to you.
warranty period.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state
Purchase Date
to state.
If you purchased your product outside the USA:
Name of Store
• This warranty does not apply. Contact your dealer for warranty information.