Related Manuals for Philips 22HFL3XX8D/10
Summary of Contents for Philips 22HFL3XX8D/10
- Page 1 Philips Hospitality TV Installation Manual for 22HFL3XX8D/10 26HFL3XX8D/10 32HFL3XX8D/10 42HFL3XX8D/10 Status: Approved Version 1.0 Date: June 2013 Author: Marian Pufulete...
-
Page 2: Table Of Contents
Contents Requirements before starting the installation ......................2 Find out the state of the TV ............................3 Re-install TV ................................4 Installation wizard ..............................6 Channel options ..............................13 a.Reordering channels ............................ 13 b.Rename channels ............................15 c.Hide channels ............................... 15 Professional Settings .............................. -
Page 3: Requirements Before Starting The Installation
Guest Remote by pressing 1,2,3,6,5,4. Go to: http://www.support.philips.com/support Enter the model number and check to confirm you have the latest version available. Confirm the software version present on TV is identical with the one from website. If not please download the latest version from website, unzip and save on to a USB key The USB key must be formatted as FAT32 and preferably empty to avoid and accidental upload of wrong setting and software. -
Page 4: Find Out The State Of The Tv
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. -
Page 5: Re-Install Tv
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If the Professional mode is active you can access the setup menu by pressing the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’... - Page 6 Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall TV set. If all is correct select “Start now” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available.
-
Page 7: Installation Wizard
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. Please select with the Up and Down arrow keys and confirm with ‘OK’... - Page 8 The next step is to choose between the options ‘Shop’ and Home’. Select ‘Home’ for installation. If you select “SHOP” an ‘e-sticker’ banner will be displayed on the TV. This is for commercial purpose only. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people.
- Page 9 Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use. It is advisable to check the settings before starting the search.
- Page 10 The options from the Settings menu are: The “Frequency scan” contains three options: “Quick”: this is a fast method to search channels but it might skip some channels (depending on the network). “Full”: the scan will search on all frequencies and will store all channels available.
- Page 11 During the channel search you can see the progress bar and how many channels are found at that time. When the search is done, you should see “Channel search complete” and a summary of the channels found. Press “OK” button on remote control to finish the search. If you would like to change the picture and sound settings, you can go to “Optimize TV picture and sound”...
- Page 12 Select “Continue” to start the wizard and press the “OK” on remote control. The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control. Once this wizard is done, you will return to the installation menu again. The last option in this menu is “Add your devices”.
- Page 13 After pressing “Done” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard. Note: This wizard will not be available anymore when you start the TV the next time. The only way to re-use this wizard is to reinstall the TV set...
-
Page 14: Channel Options
5. Channel options a. Reordering channels To reorder TV channels you need the channel plan from the Professional Settings menu. In the consumer menu you cannot rearrange channels. The Professional Settings menu can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). - Page 15 Select “Reorder” and Press the “OK” button on the remote control to reorder channels. Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position.
-
Page 16: B.rename Channels
b. Rename channels Select the channel, press the “Options” button on remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels. -
Page 17: Professional Settings
6. Professional Settings [Professional Settings] Settings especially designated for hospitality. [Professional Mode] [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the Professional Settings Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. [Room ID] Entry field to store 4 digits to set the Room Identifier. - Page 18 [TV to USB] Check Cloning section [RF to TV] Option used for SmartInstall Note: Setup and configuration for SmartInstall is not covered by this manual [Reset] Reset all settings from Professional mode to default values. [Switch on settings] All settings from this submenu are applied when the TV set is powered ON.
- Page 19 [Maximum volume] This option specifies the maximum allowable volume level of the Selectable value from 00 until 60. [Switch on picture format] This setting allows you to set a switch on picture format. The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation when the mains power is activated (cold start): [On]: The TV will always turn on (show startup channel) after the...
- Page 20 [Line 1] Line 1: First line of the welcome message. When pressing “OK” button on remote control while editing line 1 or 2, a virtual keyboard will pop up on screen. Note: Maximum 20 characters per line. [Line 2] Line 2: Second line of the welcome message. [Clear] Will delete the current welcome message.
- Page 21 [Hotel Information] The settings from this submenu will allow you to setup the pictures for the hotel information. [Display information] [On]: Enables hotel information to be available in the guest menu. [Off]: Disables hotel information to be available in the guest menu.
- Page 22 [Off]: Disables auto scart switching or break-in. [HDMI-CEC in] [Off]: Disables HDMI-CEC feature. [On]: Enables HDMI-CEC feature. Philips Easylink (HDMI-CEC) enables one-touch play and one-touch standby between HDMI-CEC compliant devices. [USB break-in] [Off]: When a USB device is plugged in, the [Multimedia] menu will not appear automatically, but users can access [Multimedia] menu from the Consumer menu by selecting “Browse USB”.
- Page 23 [Enable teletext] Enables or disables the use of Teletext OSD on pressing the Teletext button: [Off]: Disables Teletext. [On]: Enables Teletext. [Enable MHEG] Enables or disables the use of MHEG OSD on pressing the MHEG button: [Off]: Disables MHEG. [On]: Enables MHEG. [Enable EPG] Enables or disables the use of EPG OSD on pressing EPG button: [Off]: No EPG services available...
- Page 24 [Digit timeout] Defines the time interval between numeric buttons when users press digits on the remote control. Selectable values from 0.5 to 9.9 seconds. [Selectable AV] Allows the installer to define which external sources to be displayed on the source list when pressing AV button on the Guest remote control.
- Page 25 [Speaker settings] Submenu with speaker settings. [TV speaker enable] [Off]: Disables the TV Main speakers. The headphone output is not affected by this setting. [On]: Enables the TV Main speakers. [Independent main speakers] [Off]: The volume +/- on the Guest remote control will affect both the TV Main speaker and the headphone volume.
- Page 26 [Auto channel update] [ON]: Enables automatic channel update. [OFF]: Disables automatic channel update. [Auto software update] [ON]: Enables software update [OFF]: Disables software update [Skip scrambled signals] [Off]: Allows scrambled channels in the channel list. [On]: Skips the scrambled channels in the channel list. [Multi remote control] To set the color of the TV in multi remote.
- Page 27 MyChoice configuration: Free Package: Channels free to view Package 1: Package with channels available only with valid MyChoice pin code Package 2: Package with channels available only with valid MyChoice pin code ThemeTV Configuration: Edit the names for ThemeTV categories Note: ThemeTV setup is not included in this manual To select the TV channels for every ThemeTV category.
-
Page 28: Welcome Logo
IMPORTANT: Total amount of size for Hotel Information and Welcome Logo MUST be smaller than 12 Mb( megabyte There are 2 Philips logos displayed at startup. The second logo can be replaced by picture uploaded via USB. File format: 1280 x 720.png file. -
Page 29: Clone
8. Clone With cloning it is possible to copy to/from a USB device TV the configuration data and the channel list data. Place a USB Memory stick in the USB side connector of the TV. *USB device should be formatted as FAT or FAT32. Access the Professional menu by pressing the ‘RC5 SETUP’... -
Page 30: Feature Settings
9. Feature settings [Multi RC] This function allows that up to four televisions can be installed in a room whereas every TV will listen to its own RC. Once the TV is set, also every RC can be set to remember its connected TV: [Off] This function is not used;... - Page 31 Enter the Professional menu go to: Clock setup and configure the Download program. Afterwards define the country in which the TV is installed. And if it is required the Time offset. 2. Go to Installation and enable MyChoice. In this case three options are available. These are: OFF: This means that MyChoice is disabled and the packages are not available.
- Page 32 4. Defining the channel packages is the second step in the MyChoice configuration. Based on the pin code the TV channels will be displayed. Three packages are available: Free package: This package will include all channels which are available without any pin code. To add a channel to a ring you have to select the channel and press OK to tick the box in front of the channel.
- Page 33 Each package can be configured independently without having any influence on other packages, but you have to keep in mind that after activation the TV will show only the channels which are ticked for this package. Press Menu to exit the Professional menu and store all settings. 5.
-
Page 34: Csm (Consumer Setup Menu)
CSM (Consumer Setup menu) The CSM contains data about the TV software, serial number and other details. The menu can be accessed using a standard remote control or using the master remote control. 1. Using the standard remote control: press the following key sequence “1,2,3,6,5,4” 2.