Breville Barista Express Instruction Book page 15

CARE & CLEAnInG
dECALCIfyInG
After regular use, hard water can cause
mineral build up in and on many of the
inner functioning components, reducing
the brewing flow, brewing temperature,
power of the machine, and taste of the
espresso. We advise decalcifying the
machine every month and especially if not
using the machine for an extended period
eg. before going on vacation.
Press the POWER button to switch
1.
the machine off.
Pour a 50/50 mixture of white
2.
vinegar and cold tap water into the
water tank.
Remove the portafilter from the
3.
group head and place a large
container beneath the group head
and steam wand.
Press the POWER button to switch
4.
the machine on. When the brewing
temperature has been reached and
all the button lights on the control
panel have illuminated, press and
hold the 1 CUP button to commence
a manual pour. Release the button
once half the mixture of white
vinegar and water has run through
the group head.
Set the STEAM/HOT WATER dial
5.
to the HOT WATER position and
allow hot water to run through the
hot water outlet for approximately
30 seconds. Return the dial back
to the STANDBY position.
Set the STEAM/HOT WATER dial to
6.
the STEAM position and allow steam
to run through the steam wand for
approximately 2 minutes. Return the
dial back to the STANDBY position.
28
If any of the mixture remains in the
7.
water tank, press and hold the 1 CUP
button to commence a manual pour.
Release the button once the tank is
empty and nothing runs through the
group head.
In harder water environments, we
8.
recommend repeating this cycle.
After decalcifying, remove the water
9.
tank, rinse thoroughly then refill with
fresh cold water only. To rinse the
machine, repeat steps 3–7.
WARNING
Do not immerse power cord, power
plug or appliance in water or any
other liquid. The water tank should
never be removed or completely
emptied during decalcifying.
CARE & CLEAnInG
CLEAnInG tHE ConICAL BURR GRIndER
This grinder cleaning cycle removes oil build-up on the burrs which can impede
performance.
1 2 3 4
POWER GRIND AMOUNT FILTER SIZE
Unlock hopper Empty hopper Replace hopper Lock hopper
8 9 10 11
Unlock top burr Remove top burr Clean top burr with brush Clean lower burr with brush Clean chute with brush
AdvAnCEd CLEAnInG foR tHE ConICAL BURR GRIndER
This step is only required if there is a blockage between the grinding burrs and the grinder outlet.
1 1 2 2 3 3 4 4
GRIND SIZE GRIND SIZE
LOOSEN NUT LOOSEN NUT
POWER POWER GRIND AMOUNT GRIND AMOUNT FILTER SIZE FILTER SIZE
Remove hopper Remove hopper Set 'GRIND SIZE' to '1' Set 'GRIND SIZE' to '1' Use 10mm socket. Rotate Use 10mm socket. Rotate Set 'GRIND SIZE' to '16' Set 'GRIND SIZE' to '16'
(finest) (finest) 'Clockwise' to loosen the 'Clockwise' to loosen the (coarsest) (coarsest)
nut only nut only
8 8 9 9 10 10 11 11
SINGLE SINGLE DOUBLE DOUBLE
3 3
SPRING SPRING
WASHER WASHER
2 2
PUSH TO GRIND PUSH TO GRIND
1 1
1. FELT WASHER 1. FELT WASHER
2. METAL WASHER 2. METAL WASHER
3. GRIND FAN 3. GRIND FAN
Unblock the grinds exit Unblock the grinds exit Clean chute with brush Clean chute with brush Insert washers & grind fan Insert washers & grind fan Insert lower burr (drive pin Insert lower burr (drive pin
chute using the brush or chute using the brush or using long-nose pliers using long-nose pliers & cavity to align). Insert & cavity to align). Insert
a pipe cleaner a pipe cleaner flat washer & spring washer flat washer & spring washer
WARNING
Care should be taken as the
grinder burrs are extremely sharp.
5 6 7
SINGLE DOUBLE
PUSH
POWER GRIND AMOUNT
Run grinder empty Unlock hopper Remove hopper
12
SINGLE DOUBLE
PUSH TO GRIND
5 5 6 6 7 7
1 1
SPRING SPRING
GRIND SIZE GRIND SIZE
WASHER WASHER
2 2
FLAT FLAT
3 3
WASHER WASHER
1. GRIND FAN 1. GRIND FAN
2. METAL WASHER 2. METAL WASHER
3. FELT WASHER 3. FELT WASHER
Unlock & remove top burr Unlock & remove top burr Remove nut, spring & flat Remove nut, spring & flat Remove grind fan & washers Remove grind fan & washers
washer. Carefully remove washer. Carefully remove using long-nose pliers using long-nose pliers
lower burr lower burr
12 12 13 13 14 14
GRIND SIZE GRIND SIZE
FLAT FLAT
WASHER WASHER
TIGHTEN NUT TIGHTEN NUT
Rotate 'Counter-Clockwise' Rotate 'Counter-Clockwise' Insert & lock top burr Insert & lock top burr Set 'GRIND SIZE' to '5'. Set 'GRIND SIZE' to '5'.
to tighten nut to tighten nut Replace & lock hopper Replace & lock hopper
FILTER SIZE
29