GE NETWORX NX-548E User Manual page 10

10 NetworX NX-548E Receiver
Installation Instructions
Table 5. Programming settings (continued)
Location
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Zone _____
Assigned to module
#_____.
RM HE P
Segment 1 Segment 2
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
1 - Enable sensor Partition 1 keyfob
2 - Supervised Partition 2 keyfob
3 - Fire supervision Partition 3 keyfob
4 - Input option 1 Partition 4 keyfob
5 - Input option 2 Partition 5 keyfob
6 - 80-bit device Partition 6 keyfob
7 - Input option 3 Partition 7 keyfob
8 - Not used Partition 8 keyfob
Table 5. Programming settings (continued)
Location Segment 1
193 1 - Enable jam detect
Receiver options (all
2 - Enable auto
defaults off)
advance to next
zone number
3 - Keyfob user ID (off
= all keyfobs
report as user 99;
on = keyfob
reports as
learned zone #)
4 - Enable antenna
tamper (only
selectable on
international
versions; reports
as box tamper)
5 - Enable case
tamper
6 - Keyfob disarming
(0 = keyfob
disarm normal; 1
= disarm only
during entry or
partial arm)
7 - Enable wall tamper
(reports as box
tamper)
8 - Not used
194 Starting zone
numbers by bank
Receiver zone bank
setting:
setting (default = 0),
set this before 0 = 1
learning any sensors.
1 = 9
Applies only to NX8E.
2 = 17
3 = 25
4 = 33
5 = 41
6 = 49
7 = 57
8 = 65
9 = 73
10 = 81
11 = 89
12 = 97
13 = 105
14 = 113
15 = 121
16 = 129
17 = 137
18 = 145
19 = 153
20 = 161
21 = 169
22 = 177
23 = 185
195 Normal ______hours.
Supervision Windows (0 to 255 hours;
default = 24 hours)
Segment 3:
Short supervision time _____minutes (1 to 30
minutes, default = 40 minutes - disabled)
Do not change Segment 3 setting unless
required. See step 7 under
sion windows
Segment 2
None
Fire ______hours.
(0 to 255 hours;
default = 4 hours)
Transmitter supervi-
on page 6.