GE NETWORX NX-548E User Manual page 5

Transmitter options
LCD touchpads will display instructions when accomplishing
tasks.
To program the transmitter and partition settings, do the
following:
1. Enter * 8 at the keypad. On LED touchpads, the five func-
tion lights start flashing.
2. Enter the program code (factory default is 9713). On LED
touchpads, the service light flashes and the five function
lights change from flashing to on steady.
3. Enter the DIP switch setting module number for the receiver
and press #. On LED touchpads, the Armed LED turns on to
indicate the control panel is waiting for a programming
location entry.
4. Enter the zone location number and press #. On LED touch-
pads, the Armed LED turns on and the Zone LEDs display
the binary data for the current settings.
5. Press the keypad button that corresponds to the feature
number you want changed. On LED touchpads, the lights
corresponding to the feature number will turn on or off
depending on the previous state. On LCD touchpads, the
feature number will turn on or off depending on the
previous state.
6. Press * to enter the changes and automatically advance to
segment 2.
Note: If you press # instead of * in step 6, it exits the zone
location and does not save changes to transmitter
options.
7. Press # to exit zone location. To continue programming
other zone locations, repeat steps 4 to7. To exit program
mode, press EXIT EXIT.
Door/window transmitter settings
Use the following guidelines when setting features 4 and 5 (see
Segment 1 in Table 5 on page 7) for door/window transmitters:
• Feature 4 - Input option 1. Turn on this feature to disable the
transmitter's internal reed switches.
• Feature 5 - Input option 2. For transmitters that use a
normally open (N/O) external contact, leave this feature off.
For transmitters that use a normally closed (N/C) external
contact, turn this feature on.
Wireless smoke detector settings
Use the following guideline when setting feature 4 (see Segment
1 in Table 5 on page 7) for wireless smoke detectors:
• Feature 4 - Input option 1. For detectors with tamper
switches, turn on this feature to enable the tamper feature.
Note: Feature 4 must be off (disabled) when using wireless smoke
detectors without tamper switches.
4-button keyfob settings
The control panel installation manual describes how keyfob
functions 1 and 2 can be used to control relays, outputs, or X-10
devices.
Use the following guidelines when setting features 4 and 5 (see
Segment 1 in Table 5 on page 7) for 4-button keyfobs:
• Feature 4 - Input option 1. Turn on this feature to change the
Light button to keyfob function 1.
• Feature 5 - Input option 2. Turn on this feature to change the
Star button to keyfob function 2.
UFT settings
Use the following guidelines when setting features 4, 5 and 7
(see Segment 1 in Table 5 on page 7) for UFTs:
• Feature 4 - Input option 1. For UFTs, turn on this feature to
disable the transmitter's primary reed.
• Feature 5 - Input option 2. For UFTs on this feature to
disable the transmitter's secondary reed.
• Feature 7 - Input option 3. For UFTs that use a normally
open (NO) external contact, leave this feature off. For UFTs
that use a normally closed (NC) external contact, turn this
feature on.
Partition settings for keyfobs
LCD touchpads will display instructions when accomplishing tasks.
To program the transmitter and partition settings, do the following:
1. Enter * 8 at the keypad. On LED touchpads, the five func-
tion lights start flashing.
2. Enter the program code (factory default is 9 7 1 3). On LED
touchpads, the service light flashes and the five function
lights change from flashing to on steady.
3. Enter the DIP switch setting module number and press #.
On LED touchpads, the Armed LED turns on to indicate the
control panel is waiting for a programming location entry.
4. Enter the zone location number and press #. On LED touch-
pads, the Armed LED turns on and the Zone LEDs display
the binary data for the current settings. On LCD touchpads,
the display shows Segment 1 and its settings.
5. Press * to advance to Segment 2.
6. Press the keypad button that corresponds to the partition
number you want to change. On LED touchpads, lights that
turn off indicate the keyfob is active in that partition. On
LCD touchpads, partition numbers that turn on indicate the
keyfob is active in that partition.
Note: These partition settings apply only to keyfobs.
Partition assignments for other types of transmitters
are made in the panel.
7. Press * to enter the changes. To continue programming
transmitter partition settings, repeat steps 4 to 8.
Note: If you press #, it does not save changes to the current
segment, but it does save changes to previous
segments.
8. To exit program mode, press EXIT EXIT.
5