Download Print this page

GE NETWORX NX-548E User Manual

Ge car satellite tv system user manual.
Hide thumbs

Advertisement

Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Introduction
The NX-548E Receiver adds wireless capabilities to the
NetworX line of control panels. Adding a receiver makes these
control panels compatible with NX wireless transmitters.
Only three wire connections are required for power and commu-
nication to the control panel.
WARNING:
To avoid possible equipment damage
WA
or personal injury, remove power from
the control panel before making any
wiring connections to the receiver.
Internal mounting
For internal mounting, mount the receiver inside the control
panel enclosure. Use the following installation guidelines:
• Leave at least 10 in. (25 cm) above the control panel for the
receiver's antennas.
• Avoid areas that expose the receiver to moisture.
• Avoid areas with excessive metal or electrical wiring,
including furnaces and utility rooms.
To mount the receiver, do the following:
1.
Remove the appropriate knockouts on the top of the control
panel enclosure for the antenna shrouds.
2.
Assemble the antenna shrouds and fit the black O-rings to
the bottom of each shroud.
3.
Insert the shrouds into the knockout holes (Figure 1).
Figure 1.
Installing the antenna shrouds
Antenna shroud
Enclosure top
O-ring
Knockout hole
Installation Instructions
4.
Use the mounting screw provided to loosely install the edge
guide standoff in the lower mounting hole in the appropriate
space to the left of the control panel (Figure 2). Do not
tighten the mounting screw down at this time.
Figure 2.
Installing the edge guide standoff
Mounting screw
Edge guide standoff
CAUTION
5.
Slide the printed circuit board into the antennae shroud
slots, after inserting wires into antennae shrouds (Figure 3).
Figure 3.
Anntennae shrouds
Antennae
shrouds
Enclosure
Circuit
board
NetworX NX-548E Receiver
466-2225B July 2006
Copyright © 2006, GE Security Inc.
You must be free of static electricity before
handling circuit boards. Touch a bare metal
surface or wear a grounding strap to
discharge yourself.

Advertisement

   Related Manuals for GE NETWORX NX-548E

No related manuals

   Summary of Contents for GE NETWORX NX-548E

  • Page 1: Table Of Contents

    Slide the printed circuit board into the antennae shroud slots, after inserting wires into antennae shrouds (Figure 3). Figure 3. Anntennae shrouds Antennae shrouds Enclosure Circuit board 466-2225B July 2006 Copyright © 2006, GE Security Inc.

  • Page 2: External Mounting

    NetworX NX-548E Receiver Installation Instructions Align the bottom of the circuit board in the edge guide standoff and twist the standoff into place (Figure 4). Tighten the mounting screw (Figure 2). Figure 4. Installing the circuit board Antenna shroud Enclosure...

  • Page 3: Wiring

    To install the circuit board onto the back plate (Figure 7), insert the antennas into the antenna shrouds, then gently slide the top of the circuit board under the two top latches, and snap the circuit board in at the bottom latch to secure it in place.

  • Page 4: Programming

    NetworX NX-548E Receiver Installation Instructions Programming This section describes how to program the units. Programming guidelines Use the following programming guidelines: • NX-4 and NX-6 control panels can have receivers added with zones that overlap those contained in the control panel.

  • Page 5

    Transmitter options LCD touchpads will display instructions when accomplishing tasks. To program the transmitter and partition settings, do the following: Enter * 8 at the keypad. On LED touchpads, the five func- tion lights start flashing. Enter the program code (factory default is 9713). On LED touchpads, the service light flashes and the five function lights change from flashing to on steady.

  • Page 6: Testing And Troubleshooting

    NetworX NX-548E Receiver Installation Instructions Transmitter supervision windows LCD touchpads will display instructions when accomplishing tasks. To change the transmitter supervision windows, do the following: Enter * 8 at the keypad. On LED touchpads, the five func- tion lights start flashing.

  • Page 7: Programming Settings Table

    Programming settings table Table 5. Programming settings Location Segment 1 None (Transmitter to program) Zone _____ 1 - Enable sensor (default = off) Assigned to module 2 - Supervised #_____. (default = on) 3 - Fire supervision (default = off) RM HE P 4 - Input option 1 (default = off)

  • Page 8

    NetworX NX-548E Receiver Installation Instructions Table 5. Programming settings (continued) Location Segment 1 Zone _____ 1 - Enable sensor 2 - Supervised Assigned to module 3 - Fire supervision #_____. 4 - Input option 1 5 - Input option 2...

  • Page 9

    Table 5. Programming settings (continued) Location Segment 1 Zone _____ 1 - Enable sensor 2 - Supervised Assigned to module 3 - Fire supervision #_____. 4 - Input option 1 5 - Input option 2 RM HE P 6 - 80-bit device 7 - Input option 3 8 - Not used Zone _____...

  • Page 10

    NetworX NX-548E Receiver Installation Instructions Table 5. Programming settings (continued) Location Segment 1 Zone _____ 1 - Enable sensor 2 - Supervised Assigned to module 3 - Fire supervision #_____. 4 - Input option 1 5 - Input option 2...

  • Page 11: Supported Devices

    Table 5. Programming settings (continued) Location Segment 1 None Number of rounds received from last transmitter learned Testing and trou- bleshooting on page 6. Supported devices For 80-bit devices, Feature 6 must be on for Segment 1 on zone Segment 2 location.

  • Page 12: Specifications

    NetworX NX-548E Receiver Installation Instructions Specifications Compatibility NX-4, NX-6, NX-8, NX-8E control panels Frequency 319.5 MHz Wireless range 1,000 feet (304 m) Required power 12.0 VDC (provided by panel) Current draw 55 mA maximum Operating temperature 32 to 120°F (0 to 49°C) Storage temperature -30 to 140°F (-34 to 60°C)

Comments to this Manuals

Symbols: 0
Latest comments: