Download Print this page

American Dryer Corp. Gas HSI - Phase 7/FSS AD-78 III Installation Manual

Gas hsi - phase 7/fss

Advertisement

Quick Links

WARNING: For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or death.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
— Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
082401JEV/tcosta
AD-78 III
(Gas HSI - Phase 7/FSS)
Installation Manual
For replacement parts, contact the reseller from which the dryer
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette notice
pour réduire au minimum le risque d'incendie
ou d'explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
— Ne pas entreposer ni utiliser d'essence ni
d'autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre
appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
• Ne pas tenter d'allumer d'appareils.
• Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment.
• Évacuez la pièce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur
de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
— L'installation et l'entretien doivent être assurés par
un installateur ou un service d'entretien qualifié
ou par le fournisseur de gaz.
was purchased or
American Dryer Corporation
88 Currant Road
Fall River MA 02720-4781
Telephone: (508) 678-9000 / Fax: (508) 678-9447
e-mail: techsupport@amdry.com
www.amdry.com
ADC Part No. 113340

Advertisement

loading

Summary of Contents for American Dryer Corp. Gas HSI - Phase 7/FSS AD-78 III

  • Page 1 Installation Manual WARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
  • Page 2 Retain This Manual In A Safe Place For Future Reference American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation. ONLY qualified technicians should service this equipment. OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included with the dryer.
  • Page 3: For Your Safety

    YOU MUST DISCONNECT AND LOCKOUT THE ELECTRIC SUPPLY AND THE GAS SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health Administration) STANDARDS.
  • Page 4 The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJURY OR FIRE COULD RESULT. DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/SCREEN IN PLACE, EVEN IF AN EXTERNAL LINT COLLECTION SYSTEM IS USED. PLEASE OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation manual included with the dryer.
  • Page 5 SECTION I IMPORTANT INFORMATION ... 3 A. Receiving and Handling ... 3 B. Safety Precautions ... 4 SECTION II SPECIFICATIONS/COMPONENT IDENTIFICATION ... 6 A. Specifications ... 6 B. Component Identification ... 8 SECTION III INSTALLATION PROCEDURES ... 10 A. Location Requirements ... 10 B.
  • Page 6 SECTION VII REVERSING TIMER SPIN/DWELL ADJUSTMENTS ... 37 SECTION VIII DATA LABEL INFORMATION ... 38 A. Data Label ... 38 SECTION IX PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS ... 40 SECTION X BURNER AND BASKET (TUMBLER)/LINT CHAMBER MANUAL RESET HI-LIMIT INSTRUCTIONS ...
  • Page 7 SECTION I must be...
  • Page 8 must be must never be DO NOT DO NOT DO NOT DO NOT...
  • Page 10 MAXIMUM CAPACITY (DRY WEIGHT) BASKET (TUMBLER) DIAMETER BASKET (TUMBLER) DEPTH BASKET (TUMBLER) VOLUME BASKET (TUMBLER) MOTOR DOOR OPENING (DIAMETER) DRYERS PER 20’/40’ CONTAINER DRYERS PER 48’/53’ TRUCK VOLTAGE AVAILABLE APPROX. WEIGHT (UNCRATED) APPROX. WEIGHT (CRATED) HEAT INPUT AIRFLOW INLET PIPE CONNECTION must be SECTION II 75 lbs...
  • Page 11 Specifications ADG-78 III (Gas)
  • Page 14: Section Iii

    SECTION III must be should be...
  • Page 15 must be must be...
  • Page 17 must be must...
  • Page 18 must be...
  • Page 19 must be MUST BE...
  • Page 20 must not exceed must be must be DO NOT MUST NOT BE must not exceed must be must be...
  • Page 21 MUST NOT BE should must be must be DO NOT...
  • Page 22 must be...
  • Page 23 ADG-78 III (Gas) ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER) IMPORTANT: 208 VAC AND 230/240 VAC ARE NOT THE SAME. When ordering, specify exact voltage. NOTES: When fuses are used they must be dual element, time delay, current limiting, class RK1 or RK5 ONLY. Calculate/determine correct fuse value, by applying either local and/or National Electrical Codes to listed appliance amp draw data.
  • Page 24 must be MUST BE...
  • Page 25 SINGLE-PHASE (1Ø) ELECTRICAL CONNECTIONS LEADS Black White Green Positive Neutral Ground MUST BE...
  • Page 27 MUST BE...
  • Page 28 must be...
  • Page 29 Manifold Pressure* 3.5 inches W.C. In-Line Pressure 6.0 - 12.0 inches W.C. Shaded areas are stated in metric equivalents kcal/hr Per Hour MODEL Rating NUMBER Rating 204,000 51,408 ADG-78 Shaded area is stated in metric equivalent TYPE OF GAS NATURAL 8.7 mb 14.92 - 29.9 mb TYPE OF GAS...
  • Page 31 must be must be must be...
  • Page 33 must be must be...
  • Page 34 should not must be must be...
  • Page 36 SECTION IV...
  • Page 37 SECTION V must be...
  • Page 38 must be...
  • Page 39 SECTION VI must be...
  • Page 40 DO NOT...
  • Page 41: Section Vii

    SECTION VII TIMING LEGEND SPIN TIME Adjustment Position Number Time in Seconds* DWELL (STOP) TIME Adjustment Position Number Time in Seconds* * Values shown are +/- 1-second. 10.2...
  • Page 42 SECTION VIII...
  • Page 44 SECTION IX...
  • Page 46 SECTION X...

This manual is also suitable for:

Ad-78 iii