Page 1
® GPSMAP 60CS with sensors and maps owner’s manual...
Page 2
Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements.
60CS to your PC and downloading detailed maps. GPS Navigation—takes you through the process of navigating with your GPSmap 60CS and how to use GPS Navigation to customize the operation of your GPSmap 60CS. GPS Features—provides detailed descriptions of additional GPS features such as the Calendar, Calculator, etc.
GPSmap 60CS Introduction Software License Agreement Software License Agreement BY USING THE GPSmap 60CS, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFT- WARE LICENSE AGREEMENT. PLEASE READ THIS AGREEMENT CAREFULLY. Garmin grants you a limited license to use the software embedded in this device (the “Software”) in binary executable form in the normal...
The GPSmap 60CS complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are designed to provide more reasonable protection against harm- ful interference in a residential installation, and are more stringent than “outdoor”...
Warnings and Precautions ™ CAUTION: Use the GPSmap 60CS at your own risk. To reduce the risk of unsafe operation, carefully review and understand all aspects of this Owner’ s Manual—and thoroughly practice operation using the Demo Mode prior to actual use. When in actual use, carefully compare indica- ™...
Page 7
MAP DATA INFORMATION: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to us at a reasonable cost. We use a combination of govern- mental and private data sources, which we identify as required in product literature and copyright messages displayed to the consumer.
It is unsafe to operate the controls of the unit while you are driving. Failure by the driver of a vehicle equipped with a GPSmap 60CS installed to pay full attention to operation of the vehicle and road conditions while the vehicle is in motion could result in an accident with property damage and personal injury.
Section 2: Getting Started...1-7 Battery Installation and Start Up...1 Key Functions...2 Unit Features...3 Initialization...4 The Satellite Page...4 Navigating with the GPSmap 60CS...5 The Main Page Sequence...6 The Main Page Features...7 GPSmap 60CS Introduction Table of Contents Section 3: GPS Navigation...8-68 The Map Page...8...
GPS Enhanced Games...74 Non-Enhanced Game...77 Section 5: Appendices...78-96 Accessories...78 Specifcations...80 Data Field Defi nitions...82 Connecting the GPSmap 60CS to a Computer...87 Downloading MapSource Map Data...88 UTC Offset Chart...89 Map Datums and Position Formats...90 WAAS and DGPS...91 viii Wiring Diagram ...92 Index...93...
Turn the D-Ring 1/4 turn clockwise to lock in place. Locking Pin Slot Battery Compartment GPSmap 60CS Getting Started Battery Installation and Start Up Important Note When replacing batteries, use only new or fully charged bat- teries.
GPSmap 60CS Getting Started Key Functions IN/OUT Zoom Keys • From the Map Page, press to zoom in or out • From any other page, press to scroll up or down a list FIND Key • Press and release at any time to view the Find Menu Page •...
• Provides interface to a PC for faster data transfer Battery Compartment Locking D-Ring • Turn 1/4 turn counter-clockwise and lift to remove cover Battery Compartment Cover GPSmap 60CS Getting Started Unit Features GPS Helix Antenna • Provides quick satellite acquisition Auxiliary Mount Alignment Slots...
fi rst initialization, select “New Location” from the options menu, then you can use the Map Page to determine your general location so the GPSmap 60CS can search for just those satel- lites above your position.
Go To - A direct path to a selected destination (waypoint, city, address, etc.). Track - A previous path of travel that has been stored (logged) in the GPSmap 60CS. A Track allows you to repeat a path or return on the path.
GPSmap 60CS Getting Started The Main Page Sequence Whenever you turn on the GPSmap 60CS, the Power On Page is followed by the Satellite Page, which is the fi rst of the Main Pages in sequence. To view each Main Page: 1.
In each case the condition is described and often a remedy provided. Pressing the ENTER key will acknowledge and close the message window. GPSmap 60CS Getting Started The Main Page Features...
The Map Page with Data Fields and Guidance Text Using the Map Page The Map Page is the primary navigation feature of the GPSmap 60CS. The Map Page displays a detailed map of the area surrounding your cur- rent location. It allows you to pan the map with the ROCKER key as well as view your progress when navigating.
In many instances the map displays an “Accuracy Circle” surrounding the “Position Icon”. The GPSmap 60CS uses both map resolution and GPS accuracy in defi ning your location to a point within the circle. The smaller the circle, the more accurate your location.
GPSmap 60CS GPS Navigation The Map Page The Map Page Options Menu A Quick Look at the Map Page Options Stop Navigation - Stops navigation and is disabled when there is no active navigation. Recalculate - Recalculates a route and is disabled when there is no active navigation Data Fields - Allows two to four fi...
Page 21
fi eld and repeat the process. Many of the Data Field Options are related to the display of data received from other devices interfaced to the GPSmap 60CS, for an explanation of what each option represents, see page 82 of the Appendices.
Page 22
GPSmap 60CS GPS Navigation The Map Page Guidance Text Options Menu GPS Status Message when not navigating Guidance Message when navigating To display Guidance Text: 1. With Map Page displayed, press the MENU key to display the Map Page Options Menu.
ENTER to activate. When you access the menu again the “Turn Declutter Off” option will display. Restoring Default Settings This option allows you to return the map settings to factory settings. GPSmap 60CS GPS Navigation The Map Page “Measured Distance”...
The compass ring is especially helpful when using a paper map or chart in conjunction with your GPSmap 60CS for naviga- The Bearing tion. When the electronic compass is On, a compass icon appears in the indicates the status bar at the top of the display.
Page 25
When you manually turn the Compass Off, it stays off until you manually turn it On again. Sometimes, however, when you turn the Compass On, the GPSmap 60CS overrides the Compass and uses the GPS receiver to track your heading. The criteria for switching between the Compass and the GPS can be customized.
Page 26
Calibrating the Electronic Compass The Electronic Compass must be calibrated outdoors when you fi rst use the GPSmap 60CS and after new batteries have been installed. The accuracy of the Electronic Compass is adversely affected if the unit is not held level or you are near objects that generate magnetic fi...
Page 27
8. Highlight the “Go To” button and press ENTER to display the Map Page and begin navigation to the projected waypoint. The Compass Page displays a Bearing Pointer for guidance. GPSmap 60CS GPS Navigation The Compass Page Compass Page Options Menu Using “Sight ‘N Go”...
Page 28
GPSmap 60CS GPS Navigation The Compass Page The Bearing Pointer always indicates the direction to your destination from your current location. Scale The Course Pointer indicates your course of travel from your original location and the distance off course. To stop navigation: 1.
Page 29
5. Repeat Step 3 to change remaining data fi elds. To restore data fi elds to default settings: 1. Select “Restore Defaults” and press ENTER to return the page to factory settings. GPSmap 60CS GPS Navigation The Compass Page Data Field...
GPSmap 60CS GPS Navigation The Altimeter Page Range Grid Measurement Scale Elevation Status Field Rate of Current Elevation Altimeter Page Ascent/Descent Options Menu The Altimeter Page provides the user with the current elevation, rate of ascent/descent, a profi le of elevation changes over distance or time, or a profi...
2. Adjust time and distance measurement as desired using the Elevation Plot Zoom Ranges explained on following pages. 3. To clear the plot and start again, you must clear the “Track Log”. GPSmap 60CS GPS Navigation The Altimeter Page Elevation over Distance...
GPSmap 60CS GPS Navigation The Altimeter Page Zoom Ranges for Elevation over Distance Plot Zoom Ranges for Pressure over Time Plot Zoom Ranges You can set the Zoom Ranges for elevation, distance, or time when you display the “View Elevation Plot”. Ranges for vertical distance are dis- played as you press the Up and Down ROCKER keys.
2. Press ENTER to display the altitude point on the map. The point is marked by the Map Pointer with location coordinates, the compass bearing and distance from your current location. 3. Press QUIT to close. GPSmap 60CS GPS Navigation The Altimeter Page Cross-...
Page 34
GPSmap 60CS GPS Navigation The Altimeter Page Elevation over Distance Plot Delete Prompt Reset You can reset the elevation data and the maximum elevation data by selecting these ‘Reset’ options from the Altimeter Page Options Menu. To reset the elevation data and max elevation fi elds: 1.
Calibrate Altimeter Because the GPSmap 60CS relies on the Barometric pressure to determine the elevation and the pressure at any given elevation can fl uctuate, you can calibrate the altimeter to increase its accuracy. You must know the elevation or pressure at your current location, use a reliable source.
GPSmap 60CS GPS Navigation The Trip Computer Page Select “Change Data Fields” or press the ROCKER key to highlight a fi eld you want to change. Options Menu Big Numbers Using the Trip Computer Page The Trip Computer Page provides you with a wide variety of travel data useful when navigating a long distance.
(or any other) location as a waypoint and appears with name for that waypoint and a waypoint symbol. You can mark your current location from any page on the GPSmap 60CS. To mark your current location as a waypoint: 1. Press in and hold the MARK key until the Mark Waypoint Page appears.
Page 38
GPSmap 60CS GPS Navigation Using Waypoints Map Item selected as a Waypoint Information Page for a Waypoint Page for a Map Point with Data Map Point without Data To create a waypoint using the map panning arrow: 1. With the Map Page displayed, move the panning arrow (map pointer) to the map item you want use as a waypoint.
1. Use the Find Feature to display the desired waypoint informa- tion page. 2. Highlight the “Delete” button at the bottom of the page and press ENTER. Answer “Yes” to the pop-up prompt and press ENTER to delete. GPSmap 60CS GPS Navigation Using Waypoints Waypoint Symbols Chart...
Page 40
GPSmap 60CS GPS Navigation Using Waypoints Location Moving a Waypoint Project Waypoint Projected Waypoint on Page the Map To Move a Waypoint on the Map Page: 1. Use the Find Feature to display the Information Page for the desired waypoint. (Refer to page 33.) 2.
Using the Find Menu The Find Feature provides you with a method for searching for Waypoints, Cities, and Exits which are included in the GPSmap 60CS basemap. You can also fi nd Waypoint and Geocache Points you have saved. If you have downloaded Garmin MapSource mapping data that contains additional map detail, you can search for and fi...
Page 42
GPSmap 60CS GPS Navigation Using Find “Finding” icon displays while searching Pressing the FIND key with Find Menu displayed will take you to this page. Recent Finds List Searching for a location using Find By Name If you know the name of the location you want to find, the Find By Name search option may be the easiest method of searching.
• If selecting an item to add to a list of points, these three buttons will be displayed. Save - save as a waypoint. Map - display on the Map Page. Use - insert into a list of points on a route. GPSmap 60CS GPS Navigation Using Find Selected as a destination...
Page 44
GPSmap 60CS GPS Navigation Using Find Waypoint Information Page Options include “Average Location” Find Map Database Item Information Page Options The Find Information Page Options Menu offers eight options for using a Find Item as a tool for navigation. To use the Find Item Information Page Options Menu: 1.
Page 45
• Add To Route - Include this item on a New Route or add it to an existing route. (See Using Routes page 49 on for details) GPSmap 60CS GPS Navigation Using Find • View Sun and Moon - View the Sun and Moon tables for this item location.
GPSmap 60CS GPS Navigation Using Find Find Waypoints List Waypoint Information Page Waypoint Name and Symbol Waypoint Location Coordinates, Elevation and Depth (if Current Location applicable) Remove Waypoint View Waypoint on from List Map Page Searching for a Waypoint The Waypoints List is your storage file for all created and saved waypoints.
Page 47
Searching for a Geocache The Find Geocache feature allows you to view the list of geocache locations that have been either, created using the GPSmap 60CS or down- loaded from your computer. A geocache location is actually a waypoint with a special geocache symbol assigned to give special significance and to allow it to be separated from others on the waypoints list.
Page 48
GPSmap 60CS GPS Navigation Using Find Cities Options Select Maps Menu Options City Page Options Searching for a City The Find Cities feature allows you to search for any city listed in the Find Cities mapping database (either in the basemap or from downloaded detailed List mapping data).
The Exit Services Information Page displays the name of the service, its direction from the exit, and a list of the services available. At the bottom of these Information Pages are on-screen buttons for ‘Go To’, ‘Map’, and ‘Save’. GPSmap 60CS GPS Navigation Using Find Find Exits List...
Page 50
GPSmap 60CS GPS Navigation Using Find Find Addresses Search Page Find Address Matches Address Information Searching for an Address The Find Addresses feature allows you to search for an address within the coverage of downloaded detailed mapping data. Enter the street number, street name and city and the Find Feature will match that data with addresses in the map database.
For name streets, like Main or Elm, enter the core name instead of “E”, “W”, etc., as the search will move faster. When done a list of matches appears below. Select one and press ENTER to display the Information Page. GPSmap 60CS GPS Navigation Using Find Options...
GPSmap 60CS GPS Navigation Using Find Find POI Topic List Search Method Select Category Category List POI Information Page Searching for a Point of Interest You can use the Find Point of Interest feature to locate a nearby restaurant, lodging, landmark, public building, park, etc. However, you...
• Calendar - An outdoor calendar with data access as well as waypoint association. • Alarm Clock - This feature allows you to use the GPSmap 60CS as an Alarm Clock. • Calculator - A standard or scientifi c calculator for measurement conversions, etc.
GPSmap 60CS GPS Navigation Using Tracks Tracks Page with Saved Track Log Options Menu Track Log Setup Page Using a Track Log The Tracks feature creates an electronic trail on the map page as you travel about and is referred to as a Track Log. A track log contains infor- mation about points along its path, including time, position, elevation and depth (requires NMEA input, see page 56).
Page 55
Use the Panning Arrow to identify a point on the track that you want as the End Point and press ENTER. A “Saving Track” message appears followed by the Saved Track Page. (cont. on page 46) GPSmap 60CS GPS Navigation Using Tracks Save Track Page...
Page 56
GPSmap 60CS GPS Navigation Using Tracks 151ST ST Saved Track on the Map Page Saved Track Page Area Calculation Option Start Calculation Stop Calculation Save Calculated Track 4. The Saved Track Page allows you to: Rename the track, view the track distance, view the calculated area encompassed by the track (an area is defi...
Profi le Options Menu - Displays only when you have DEM maps loaded on your GPSmap 60CS. A Track Elevation Profile can also be created from Digital Elevation Models (DEM) maps (MapSource U.S. Topo 24K) which include elevation data contained in the map.
Page 58
GPSmap 60CS GPS Navigation Using Tracks TracBack Page Create User Waypoint Prompt To Use the TracBack feature: 1. With the Saved Tracks Page for the track or the Track Log displayed, highlight the TracBack button and press ENTER to display the TracBack Page.
Creating and Using a Route Route navigation allows you to create a sequence of intermediate waypoints which lead you to your fi nal destination. The GPSmap 60CS stores 50 routes, each with up to 250 waypoints each. A route can be cre- ated and modifi...
Page 60
Methods of navigating to a destination: • When you activate the “Go To” button on the Information Page for a User Waypoint or other Find Menu items, the GPSmap 60CS creates a straight path (point to point) from your current location to that location.
ROCKER key Up and Down arrows. To exit the preview page, press the QUIT key. 6. To stop navigating, select “Stop Navigation” from the Map or Compass Page and press ENTER. GPSmap 60CS GPS Navigation Using Routes This fi eld changes...
GPSmap 60CS GPS Navigation Using Routes Saved Routes Route Leg Transition Options Route on the map transitions to the next leg point when you are within a 1 mile radius of that point. Route Options To delete the route: Options 1.
Page 63
Route” option and press ENTER. To create a vertical profi le of the route: (Available only if Garmin MapSource U.S. Topo 24K map data is used. See page 88 for details.) 1. Select “Profi le” and press ENTER to display the route profi le.
GPSmap 60CS GPS Navigation The Highway Page Highway Page with an Active Route Highway Page Options Menu Data Field Display Options The Highway Page Whenever navigating a route, the Highway Page will guide you to the destination using data fields and a graphic highway. Up to four user selectable data fields display information such as speed, distance, time to next point on the route, etc.
The Setup Menu The Setup Menu allows you to customize the GPSmap 60CS to your personal preferences. Each selectable setup page is identified by an icon, which when highlighted displays the page when you press ENTER. To access the Setup Menu: 1.
GARMIN - The proprietary format used to exchange waypoint, route, track log and MapSource data with a PC. GARMIN DGPS - The proprietary format used with a Garmin dif- ferential beacon receiver (e.g., GBR 23). Provides for tuning of the beacon receiver directly from the GPSmap 60CS.
Page 67
ENTER. Use the ROCKER key to highlight the desired setting and press ENTER. 4. For Garmin DGPS or RCTM In/NMEA Out, use the ROCKER key to highlight “Beacon” and press ENTER. Use the ROCKER key to select “Scan” or “User” and press ENTER.
GPSmap 60CS GPS Navigation Tones Setup Tones Sound when Check to Mute all Tones Setup Page Page Sequence Setup Restores to original setting Page Sequence Setup Page Tones Setup The Tones Setup Page allows you to customize the signal tones for a variety of unit features.
Using the Map Setup Feature The map display for your GPSmap 60CS is user confi gurable. A factory set of default settings currently control the Map Page display and may be satisfactory for your current requirements. The Map Setup pages...
GPSmap 60CS GPS Navigation Map Setup The “General Settings” Map Setup Page The “Tracks Settings” Map Setup Page The “Points Settings” Map Setup Page Map Setup - General Settings The fi rst page of the Map Setup feature is the General Settings Page.
Page 71
The last page of the Map Setup is the Marine Settings Page. Use this page to control the display of marine chart items when using downloaded marine charts (i.e. MapSource BlueChart ® marine mapping data). GPSmap 60CS GPS Navigation Map Setup The “Text Settings” Map Setup Page The “Map Information” Map Setup Page...
GPSmap 60CS GPS Navigation Routing Setup Routing Setup Page Follow Road Options Routing Setup The Routing Setup Page allows you to customize the manner in which routing functions behave. There are setup and option menus for route creation and methods of navigation.
Geocache Setup The Geocache Setup Page allows you to find and record items hidden at geographic locations. Refer to the Garmin website for details and how to download geocache locations from the internet (www.garmin.com). To use the Geocache Setup feature: 1.
4. Daylight Savings Time offers choices of Yes, No and Auto. Units Setup The Units Setup Page allows you to select the units of measurement for your GPSmap 60CS. To use the Units Setup feature: 1. Access the Units Setup Page.
Compass Calibration Page. Follow instructions on page 16. To calibrate the Altimeter: 1. Select Altimeter and press ENTER to display the Altimeter Calibration Page and follow instructions on pages 25 and 66. GPSmap 60CS GPS Navigation Heading Setup Display Options...
GPSmap 60CS GPS Navigation Altimeter Setup Enter the correct Enter the correct elevation barometric pressure Altimeter Setup The Altimeter Setup Page allows you to setup the Altimeter to self calibrate each time you turn on the unit, to function as a barometer or to manually calibrate when you have accurate elevation or pressure data.
Calibration Complete mined by the GPS receiver Press ENTER Placing your name and phone number on this page may aid in recovery of your unit should it become lost GPSmap 60CS GPS Navigation Altimeter Setup Calibration Failed Press ENTER and retry...
GPSmap 60CS GPS Navigation Proximity Waypoints Use the ENTER key to Review or Remove an entry. Proximity Waypoints List Selected Waypoint Proximity Waypoints The Proximity Waypoints Page allows you to establish waypoints that have alarm circles around them at specified distances. The alarm helps you to avoid locations that are restricted or otherwise to be avoided.
6. To view other calendar formats, Sun and Moon or Hunt and Fish extended data for a specifi c date and location, press the MENU key and use the ROCKER key to make your choice. GPSmap 60CS GPS Features Calendar...
Alarm Clock Calculator Alarm Clock The Alarm Clock Feature allows you to use your GPSmap 60CS as an alarm clock. You can choose from different alarm tones, and use the “Snooze” feature to delay the alarm for an additional seven minutes.
Stopwatch This feature allows you to use the GPSmap 60CS as a stopwatch, which includes a lap timer. You may also have the unit record the lap time based on distance. To start the stopwatch: 1. Use the ROCKER key to highlight the ‘Start’ fi eld and then press ENTER.
GPSmap 60CS GPS Features Sun and Moon Tables Location Options Sun and Moon The Sun and Moon Tables provide you with a graphic depiction of the sun and moon relative to the Earth. Sun and moon positions can be displayed for any time, date and location on Earth.
ENTER. The Location fi eld will now display the name of the fi nd item. 4. To return to the current date, press MENU and then ENTER. GPSmap 60CS GPS Features Hunt and Fish Tables Hunt and Fish Page...
Unopened Symbol Games The GPSmap 60CS provides games as an entertainment feature. Sev- eral of these games employ GPS as a virtual component in the play. To select and play a game: 1. Access the Main Menu and use the ROCKER key to select the Games icon.
(about the size of an American football field). The difficulty levels are: Easy, Normal and Hard. These levels deter- mine how often Gekos appear. The pace quickens and values vary as difficulty levels increase. GPSmap 60CS GPS Features GPS Enhanced Games...
GPSmap 60CS GPS Features GPS Enhanced Games Nibbons In this GPS game, you must walk around the board collecting the flags as they appear. As you walk, your “tail” will grow. You may travel anywhere on the screen but you cannot walk on your tail, or you will lose a life.
To defeat the dragon, use ENTER to place an arrow in a shaded platform. Use the ROCKER key to point and ENTER to shoot. GPSmap 60CS GPS Features Non-Enhanced Game Game Symbols Pit Warning...
Garmin products. Accessories offered for sale by other manufacturers have not necessarily been tested or approved by Garmin for use with Garmin Products. Use of such accessories might cause damage to your Garmin Product and void the terms of the warranty. Using Garmin Accessories with other manufacturer’...
Page 89
(attaches to belt or waistband) USB Connector (under weather cover) Remove Belt Clip Plug Power/Data Cable Connector (Serial Port) (under weather cover) Back of GPSmap 60CS GPSmap 60CS Appendices Accessories Suction Mount Kit Auto Dash Mount Kit Marine Mount Kit Bicycle Mount Kit...
GPSmap 60CS Appendices Specifi cations GPSmap 60CS PHYSICAL Case: Rugged, fully gasketed, water resistant, IEC-529, IPX7 (Submersible 1 meter @ 30 minutes) Size: 7.1”H x 2.4”W x 1.3”D Weight: 5.4 ounces (153 g) with batteries installed Display: 1.5”W x 2.2”H, 256-color, high resolution, transrefl...
Page 91
Specifi cations subject to change without notice. 1. Subject to proper user calibration. 2. The temperature rating of the GPSmap 60CS may exceed the usable range of some batteries. Some batteries can rupture at high temperatures. 3. Subject to accuracy degradation to 100m 2DRMS under the U.S. DoD imposed Selective Availability (SA) Program.
The following list provides a brief description of each data field Data Field Defi nitions option. Some of these options are supported only by devices interfaced to your GPSmap 60CS. Accuracy GPS - The current accuracy of you GPS determined location. Ambient Pressure - The uncalibrated current pressure.
Page 93
GPSmap 60CS Appendices Distance - Next - The distance to the next point on a route. Data Field Defi nitions Distance - Destination - The entire distance, from beginning to end, of a route. ETA - Next - The estimated time that you will arrive at the next point on your route, if you maintain your current speed and course.
Page 94
GPSmap 60CS Appendices Odometer - The total distance you have traveled for all trips. Data Field Defi nitions Off Course - The distance off your direct course line, right or left. Pointer - The arrow that indicates the direction to travel to the next point on a route.
Page 95
Vertical Speed - The rate of altitude gain/loss over time. Vertical Speed Dest - The measurement of your rate of acsent/decsent to a predetermined altitude. Water Speed - The data acquired from measurement devices interfaced to the GPSmap 60CS is used to calculate your current speed over water.
Page 96
Water Temperature - The temperature of water at a measured depth Data Field Defi nitions using measurement devices interfaced to the GPSmap 60CS. Waypoint - Destination - The last point on a route, your destination. Waypoint - Next - The next point on your route.
Garmin MapSource Map Data CDs. You can also save routes, waypoints, and tracks from the GPSmap 60CS to MapSource. Refer to the MapSource User’ s Guide provided with your MapSource CDs. To connect to your computer using the USB connector: 1.
Find Features that require maps like City Select, City Navigator and Blue Chart and DEM Elevation Profi les that require U.S. TOPO 24K maps. Visit the Garmin website for details on all of the maps for use with the GPSmap 60CS.
Lines of latitude and longitude on a map or chart are referenced to a specific map datum. Every chart has a map datum reference and the GPSmap 60CS can be set to match most of those commonly used. If you are navigating and comparing the GPS coordinates to a map,...
GPS by the U.S. Department of Defense under their Selective Availability (SA) program. Refer to the U.S. Coast Guard’ s web site: http://www.navcen.uscg.gov/ for locations and the status of the differential sites. Using DGPS requires additional equipment. GPSmap 60CS Appendices WAAS and DGPS...
GPS receiver. The NMEA 0183 version 3.01 interface format is supported by the GPSmap 60CS and enables the unit to drive up to three NMEA devices. NMEA 0183 Version 3.01 Approved Sentences: GPGGA, GPGLL, GPGSA, GPGSV, GPRMB, GPRMC, GPRTE, GPVTG,...
This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost.
Need help?
Do you have a question about the GPSMAP 60CS and is the answer not in the manual?
Questions and answers