Lux Products TX9100U Quick Start Installation Manual

Universal programmable thermostat

Advertisement

Quick Links

1
OF F
Turn OFF the power to both
your heating and cooling units
at the circuit breaker.
3

INSTALL NEW THERMOSTAT BASE

W3
E G Y R O W2 B
Remove your old thermostat. Install the new thermostat
base (using the same mounting holes if possible). Connect
the wires matching the exact terminal letters from your wires,
to the terminal letters on the new thermostat.
NOTE: If you have both a "B" and an "O" wire, see the notes
on the back page of this instruction sheet.
5

TEST HEAT AND COOL OPERATION

HEAT
Set the system switch to the
OFF
desired temperature mode.
COOL
Adjust the SET Temperature to the
desired comfort setting.
(NOTE: this set point will only be
temporary until the program
periods are saved in memory.)
DOWNLOAD THE FULL INSTRUCTION MANUAL
This sheet is just a quick start guide, and there are many more instructions and topics covered in the full version of the manual for
this product. The complete version PDF can be obtained at "http://www.luxproducts.com". Click on SUPPORT, then
INSTRUCTION MANUALS.
ONLINE THERMOSTAT TROUBLESHOOTING GUIDES
If you are having difficulties with the installation or the operation of your thermostat, please review the online troubleshooting
guides for your model. These troubleshooting guides cover the most common symptoms that you may observe. The
Troubleshooting Guides are located at "http://www.luxproducts.com". Click on SUPPORT, then TROUBLESHOOTING GUIDES.
CONTACT OUR TECHNICAL SUPPORT DEPARTMENT
If you require need assistance with your product, please contact our Technical Assistance department between 8:00AM and
4:30PM Eastern Time from Monday through Friday, at 856-234-8803. Our website also permits you to email your technical
questions to our support staff at your convenience by visiting "http://www.luxproducts.com", and clicking on the CONTACT US tab
at the top of the page.
LUX
TX9100U UNIVERSAL PROGRAMMABLE THERMOSTAT
®
QUICK START INSTALLATION GUIDE

SHUT OFF POWER

L
72F
70F
68F
© 2012 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED
2
BEFORE removing thermostat, label your
existing wire connections with the labels
provided. Cover any "unused" wires with
electrical tape.
4

INSTALL ALKALINE BATTERIES

Restore the power to your heating and cooling units.
Install new Alkaline batteries into the thermostat. NOTE:
Please use Duracell or Energizer Alkaline batteries ONLY for
all LUX
®
thermostats requiring batteries. BE SURE TO
CHANGE THE BATTERIES AT LEAST ONCE A YEAR, to ensure
consistent and reliable operation of your heating/cooling
system.
6

SET THE CLOCK...

SET THE TEMPERATURE PROGRAMS

Thank you for choosing LUX Products, and
we hope that you will enjoy using your new
thermostat along with its many energy
saving features.
53000

LABEL WIRES

4
5
6
A
AU
C
C1
DH
E
F
H
H1
H2
MDO
L
O
OT
OT
R
R
RH
T
TC
V
V

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TX9100U and is the answer not in the manual?

Questions and answers

Summary of Contents for Lux Products TX9100U

  • Page 1 4:30PM Eastern Time from Monday through Friday, at 856-234-8803. Our website also permits you to email your technical questions to our support staff at your convenience by visiting “http://www.luxproducts.com”, and clicking on the CONTACT US tab at the top of the page. © 2012 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED...
  • Page 2: Cautions And Warnings

    TX9100U QUICK START WIRING GUIDE 53000 WIRING DIAGRAM NOTES: CAUTIONS AND WARNINGS: • Label every wire terminal designation on your existing thermostat • The thermostat requires batteries to operate and failure or sub- wiring before removing your old thermostat. standard performance of the batteries may impair or prevent the correct operation of the thermostat.

Table of Contents