SHR-4160N/P USER’S MANUAL Safety Regulations Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. Do not use multiple plugs at once. This may cause abnormal heat generation or fire Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you.
Before we start This User’s Manual describes the basic usage of SHR-4160N/P. This Manual con- tains all the matters necessary for using SHR-4160N/P such as brief instruction, part name, function, connecting other equipment, and menu setup of SHR-4160N/P. SEC retains the copyright on this User’s Manual.
Contents Safety Regulations Before we start Standards Approvals Chapter 1 Overview 1. Introduction 2. Features 3. Part Names and Functions Chapter 2 Installation 1. Installation Environment Setup 2. Checking Product & Accessories 3. Additional HDD Installation Chapter 3 Connecting with Other Equipment 1.
Page 5
Chapter 5 Menu Setup Before Use 1. System 5-12 2. Camera 5-16 3. Monitoring 5-18 4. Record Mode 5-19 5. Event Record Mode 5-24 6. Record Schedule 5-26 7. Backup 5-28 8. Network 5-32 9. Network Setup Chapter 6 PTZ Device Control 1.
SHR-4160N/P USER’S MANUAL Introduction The Digital Video Recorder(DVR) compresses the camera input data from 16 channels into a MPEG4 video file and the voice input data into a G.726 audio file respectively to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously.
Features 16 CH Composite Input Connectors NTSC/PAL Video Source Compatible Able to record the CIF size (NTSC : 352 x 240 / PAL : 352 x 288) video image at the speed of 360ips(NTSC) / 300ips(PAL) 16 CH Loop Through Video Connectors Hard Disk Overwrite Mode Large quantity HDD backup function by using IEEE1394 and USB2.0, USB2.0 Memory, Backup function by using an external CD/DVD writer.
SHR-4160N/P USER’S MANUAL Part Names and Functions Name Function Displays power on/off condition. Power LED Displays both network connection and data transmis- Network LED sion conditions. Back Up LED Displays Back Up Mode. Indicates Normal Access to HDD. HDD Access Upon Access to HDD, LED repeats on and off.
Name Function Video/Audio, set to the system, is recorded to 15 PANIC Button ips(NTSC)/ 12.5 ips(PAL). The image quality of video recording is very high and PANIC its size is CIF. REC LOCK Locks the REC key motion. Button REC LOCK KEY Sets up Digital Zoom(x2).
Page 13
SHR-4160N/P USER’S MANUAL Caution Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. Name Function...
SHR-4160N/P USER’S MANUAL Installation Environment Setup Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. You shall pay attention to the following before you use the product.
Checking Product & Accessories Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it. Main Body User’s Manual One Power Cord Two Brackets...
SHR-4160N/P USER’S MANUAL Additional HDD Installation You may add up to 3 more HDDs to the product. However, since the product contains has many parts which may incur electric shock, accident, or product breakdown and improper installation or setup may disturb HDD recognition or normal product operation, you shall consult with an expert of the agency where you bought the product.
Page 19
2.Detach the cover from the product. (Pull out the cover slightly and lift from the back side to detach.) 3. A bracket is fixed to each side of HDD. Please loosen the screw of the bracket to which you want to fix HDD. BRACKET-HDD...
Page 20
SHR-4160N/P USER’S MANUAL 4.Pull BRACKET-HDD to the product center to detach the fixed part at the bottom to detach BRACKET-HDD from the product. 5.Tighten 4 SCREW-SPECIALs(BWH,6-32UNC,L10.5), supplied as an accessory to fix HDD to BRACKET-HDD. (Screw tighten force shall be strong enough to resist...
Page 21
6. Restore HDD installed BRACKET-HDD. (Assembly shall be done in the reverse procedure of disassembly as follows. Align the 5 fixing points at the bottom with the BRACKET-HDD fixing holes respectively and push BRACKET-HDD out of the product to align the screw fixing holes. Then, tighten the screws firmly.) 7.
Page 22
SHR-4160N/P USER’S MANUAL 8. Check the connector, wiring, and cable fixing condition inside the product and close the cover. 9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side) You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.
Page 23
Attention Attention ! Regarding the sub fan, you need additional brackets and sub fans as follows. The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan. @ Fix the fan as follows.
Page 24
SHR-4160N/P USER’S MANUAL # Please install the fan to be seen from the front view of the set.
- Wait until the HOT PLUG connected hard disk is stabilized enough (approx. 2 sec- onds per each hard disk) and click CONNECT in SHR-4160N/P MENU before use. - Be sure to click DISCONNECT in SHR-4160N/P MENU to delete IEEE1394 Device safely.
Page 30
Note Note Refer to Appendix 2 to see which HDD specifications are supplied.
USB device to the vailable to use with connecting the same kinds of USB device to the USB terminal on the front and back of SHR-4160N/P USB terminal on the front and back of SHR-4160N/P...
Connecting Alarm Input/Output The Alarm IN/OUT port in the back of SHR-4160N/P is composed of the following elements. ALARM IN/OUT Connection Name Function - ALARM IN1 - ALARM IN2 - ALARM IN3 - ALARM IN4 - ALARM IN5 - ALARM IN6...
Tx(–) Rx(+) Tx(+) Baud Rate covers 600, 1200, 2400, 4800, 9600, 19200, and 38400. Caution Caution Check if RS-485 Device is compatible with SHR-4160N/P first. Then pay attention to the polarity of RS-485 which has two poles, + and -.
A new HDD may require more time for the initialization until the Live screen appears due to the initialization period of the new HDD. If the Live screen does not appear at all or the button in front of SHR-4160N/P repeats blinking, please check the connection across the product body. If you find any error, please ask the shop where you bought the product.
Live screen Mode Definition of Live Screen Icon The Live screen icons of SHR-4160N/P display the current setup and function status of each screen. V.Loss CAM_01 CAM_01 : Recording Icon Each icon represents Normal / Panic / Event(Alarm+Motion) / Schedule Recording.
Page 38
If there is no more video data input with Video On, [V.Loss] appears in the channel. If you set Video On/Off to Off, [V.Off] will appear. Definition of Live Screen Mode SHR-4160N/P receives 8 live images and displays them in the following 8 modes. CAM_01 CAM_02 CAM_03 CAM_04...
Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH16 Button] The following figure shows Live Mode of SHR-4160N/P after converted. The default is 16 Split Screen Mode. The 9 Split Screen mode default is [9Split 1] for [CH1 ~ CH9], [9Split 2] for [CH10 ~ CH16], and [9Split Screen change] for [9Split 1] and [9Split 2] alternatively.
SHR-4160N/P USER’S MANUAL Live Channel Selection and Audio On/Off Setup In other split modes than Full Screen Mode, 16 Split Mode, and Screen change Mode, you may choose a channel to be displayed in each split area on your own. Meanwhile, the channel whose MENU is set to Audio On can set up Audio On/Off in all Live Modes.
Freeze and Zoom Freeze Function Freeze pauses the video image in Live Screen, only available in Live Mode. You can set up Freeze On/Off with [FREEZE] button and [FREEZE LED] is turned on or off depending on the Freeze On/Off setup condition. Zoom Function Zoom enlarges the selected area twice, only available in Full Screen Mode.
SHR-4160N/P USER’S MANUAL Event Monitoring Event Monitoring displays the channel synchronized with a specific event (Sensor/Motion/Video Loss) on the screen when it occurs. Event Monitoring On/Off and Event Duration setup is available in [Menu] [Monitoring]. If you set the Event Monitoring interval to 5 seconds and an event occurs at CH2 in the beginning as in the following figure, the system will display CH2 in the whole screen for 5 second.
Spot-out Monitoring Spot-out Monitoring has nothing to do with Live Screen Output, monitoring the full screen of a certain channel. If you select Monitoring in the MENU screen, you can make a channel among CH1 to CH16 spot out or you can output channels one by one at an interval as Screen change Mode of Live Mode.
SHR-4160N/P USER’S MANUAL Before Use Selection The yellow cursor shows the current window. Use the ,❷,➛, ❿ button in the front to move the cursor on your desirous menu. If you press the “Enter” key with the cursor clicking on your desirable menu, the system will enter the new mode.
System System Menu has the following items in detail. Date/Time/Language Setup Date Press the “Enter” button and the ➛ or ❿ button to move to Y/M/D. Use the or ❷ button to change the date. Press the “Enter” button to come out of the mode. Time Press the “Enter”...
Page 47
SHR-4160N/P USER’S MANUAL Note Note [Date/Time Change] Pressing “OK” after you change date and time, you will be asked by a pop-up win- dow if you really confirm the change. Here, press “Yes” to change the time. Since Date/Time does not change in backup process, be sure to stop the backup process before you change Date/Time.
Page 48
The Default Password is 4321. New Password This is used to change the system password inside SHR-4160N/P. You are allowed to create a password up to 8 digits. Press the “Enter” button and then a channel button from 0 ~ 9 on your left to finish input. If you press the “Enter” but- ton after change, the system will automatically turn to “New Password Confirm”.
SHR-4160N/P USER’S MANUAL Load Factory Default This initializes all the menu preset values. The recorded data will not be deleted. Press “OK” in the confirmation window to start initializing. System Log System Log is used by a controller to check crucial records.
System Log List Panic Record End Panic Recording End System Start System Start Login(Admin) Viewer Login (Admin) Time Change Date/Time Change Logout(Admin) Viewer Logout (Admin) Load Factory Default System Initialization Login(User) Viewer Login (User) System Upgrade System S/W Change Logout(User) Viewer Logout (User) Disk Full No Space for HDD...
Page 51
Usage : Internal HDD [USB] Usage : External HDD (Extended HDD or Backup HDD) A physical hard disk connected with the USB port in the back of the SHR-4160N/P main body [IEEE1394] Usage : External HDD (Extended HDD or Backup HDD)
IEEE1394 Hard Disks. As for disconnecting, be sure to press “Disconnect” and detach IEEE1394 Hard Disk from the SHR-4160N/P main body safely.(Be sure to pause recording or backup process.) Pressing “Disconnect” cancels and detaches all...
SHR-4160N/P USER’S MANUAL USB Device Setup You can set up USB Memory/USB CD(DVD). If you want to stop using the USB device, you are recommended to press "Disconnect" first before you pull out the device from the main body. Caution...
Page 54
Sets up either Half Duplex or Full Duplex. Note Note If you select Remote Control Device, you may not PTZ device with SHR-4160N/P. The PTZ button in front of SHR-4160N/P becomes inactivated. Press the PTZ button and the PTZ ban icon( ) will appear.
SHR-4160N/P USER’S MANUAL System Shutdown Remote Control Device Terminates the work in action safely and turns the power off. Press “OK” in the confirmation window and plug out when you see “Safe to Power Off”. Caution Caution [System Shutdown] Power-off without terminating the system in the System Shutdown menu may incur...
Camera The detailed Camera Menu items are as follows. Camera Configuration Video On : Camera images from a selected channel appear. Off : Camera images from a selected channel disappear. Covert1 : Displays other information than the image information on the selected channel. Covert2 : Hides all the information on the selected channel.
Page 57
SHR-4160N/P USER’S MANUAL Title You can name the camera of a selected channel. If you press the [Enter] button, the Virtual keyboard will come out. ❿¤Virtual Keyboard If you move the cursor, you can type text by text. Up to 15 texts can be typed.
A protocol supported by PTZ device The following protocols are now being supported. Samsung / Vic. / Pan. / AD / Phi. / Ern. / Pel-D / Pel-P / Vcl. / Dia. / Kal. Baudrate Baudrate supported by PTZ device , 600/ 1200/ 2400/ 4800/ 9600/ 19200/ 38400 Parity Defines one among None, Even, and Odd.
SHR-4160N/P USER’S MANUAL Screen Setup This is a window to adjust Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set up Brightness/Contrast/Color. Once selected, the channel appear in the PIP area on the right.
Monitoring Event Monitoring You are able to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous. Off : Event Monitoring does not operate to turn to the screen where an event occurs. 3sec/ 5sec/ 10sec/ 20sec/ 30sec : For the period, the screen is seen before the next screen appears.
Page 61
SHR-4160N/P USER’S MANUAL Monitor Out You may not use both VGA Output and Composite/S-Video Output at the same time. Accordingly, the user shall choose either one. Composite : The output will come out from the "Composite / S-Video Output" port.
Record Mode NTSC If you press the front “REC” button, the mode to be recorded will be determined. For Event Recording Mode value setup, refer to 5-19. Event Record Mode Setup Menu. Mode On : Pressing the REC button starts recording the current channel. Off : Even pressing the REC button does not affect current channel recording.
SHR-4160N/P USER’S MANUAL Event Record Mode The detailed items of Event Record Menu are as follows. Evnet Record Mode NTSC Determines a mode to be recorded when an event occurs. V. Size (Video Size ) Determines the size of a screen to be recorded.
Page 64
Quality Recording resolution will be determined. HH(Very High)/H(High)/N(Normal)/L(Low). Note The resolution Full D1 can be set from the 7.5ips(NTSC)/6.25ips(PAL) recording frame. The resolution Halfl D1 can be set from the 15ips(NTSC)/12.5ips(PAL) recording frame. The resolution CIF can be set from the 15ips(NTSC)/12.5ips(PAL) recording frame. But, if the resolution is CIF and the number of camera is odd number, 30ips(NTSC)/ 25ips(PAL) is supported.
Page 65
SHR-4160N/P USER’S MANUAL Alarm Detection Setup Sensor State Off : Sensor does not operate. N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued.
Motion Detection Setup M.D State Off : Motion Detection does not operate On : Motion Detection starts operation. Area Select the Motion Detection zone. It is composed of 45x40(NTSC) / 45x48(PAL) sized Block. You are forbidden to determine 4 block rows(Up/Down/Left/Right) to allow them to be displayed in all monitors.
Page 67
SHR-4160N/P USER’S MANUAL Sensitivity Determines Motion sensing sensitivity. Sensitivity grade consists of Low Medium Very High in the ascending order. Alarm-Out Selects Alarm-Out scope when Motion occurs. At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to synchronize with the current motion channel.
Record Schedule You may select a time when recording starts automatically. Setup by the weekday or time. The default is set to “None”. Pressing “CH > “ copies the value of Channel 1 to all the channels. The horizontal axis numbered from 0 to 23 represents the time value. The vertical axis numbered from S to H represents the day value.
Page 69
SHR-4160N/P USER’S MANUAL Both(Continuous, Event) On occurrence of Event, Continuous Recording is replaced with Event Recording Mode. Holiday If you press “Holiday”, a calendar pops up and you are able to designate holidays. Move to a date and press “Enter” to complete designation.
Backup The detailed items of Backup Menu are as follows. HDD Backup Setup In the presence of the device, the free space and backup device will be displayed. Select the backup date and time and the camera number, then press "Start". Whenever you change the start date/time, the end date/time, the free space is updated and displayed.
Page 71
SHR-4160N/P USER’S MANUAL USB Device Backup Setup In the presence of the device, the free space and backup device will be displayed. Select the backup date and time and the camera number, then press "Start". Whenever you change the start date/time, the end date/time, the free space is updated and displayed.
ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE. Broadbandwidth Designate the speed of the network to which the SHR-4160N/P main body is connected. Unlimited/2Mbps/1Mbps/600Kbps/300Kbps In the ADSL mode, you may choose either 600Kbps or 300kbps as the bandwidth.
Page 73
Determines Subnet Mask Address in the SHR-4160N/P main body. Sets up DNS Address in the main body of SHR-4160N/P. The default of DNS is 168.126.63.1. Generally, you don’t have to alter the DNS default but you may be hard to connect to the network sometimes if you use DHCP or ADSL.
Page 74
If you use IP Router, you are recommended to rather determine IP and Port numbers to be allocated to the main body of SHR-4160N/P from the IP Router setup menu, set the connection mode to Static IP for the main body of SHR-4160N/P, and input the determined IP and Port number in IP Router than use the DHCP function.
Page 75
SHR-4160N/P USER’S MANUAL Callback Settings Callback delivers a callback message to the IP where SmartViewer is already running when an event corresponding to Alarm, Motion Detection, or Video Loss occurs from the set. On/Off : Off is the default and On is optional.
Network Setup Port setup for SmartViewer connection. The port value shall be the same as the Port(TCP/IP) value of the set to regis- ter DVR(Setup Site Setup) with SmartViewer. When you use an IP router, you shall forward the activated port by the current setting value.
Use direction keys to move this bar until you reach the channel with the PTZ symbol and press the PTZ button in front of SHR-4160N/P to enter PTZ device Control Mode. If you succeed in entering PTZ device Control Mode, the PTZ symbol on the moni- tor screen will turn yellow from white while the PTZ button in front of SHR- 4160N/P will turn blue.
Page 79
Note If you select Remote Control Device, you may not control PTZ device with SHR- 4160N/P. It’s because the PTZ button in front of SHR-4160N/P remains inactivated. Press the PTZ button and the PTZ ban icon( ) will appear. It’s because the RS- 485 port setup was done for Romote Control Device.
Press the LEFT or RIGHT button in front SHR-4160N/P in PTZ device Control Mode to control PTZ device horizontally. TELE WIDE VIEW PRESET TILT Press the UP or DOWN button in front SHR-4160N/P in PTZ device Control Mode to control PTZ device vertically. TELE WIDE VIEW PRESET ZOOM Press the TELE/WIDE button in front SHR-4160N/P in PTZ device Control Mode to zoom in or out PTZ device.
Memorizes up to 20 PTZ device positions at the moment. Note Note For AD Protocol PTZ device , this memorizes only 7 positions. Press the SET button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to set up Preset. TELE WIDE...
Page 82
SHR-4160N/P USER’S MANUAL Move the cursor right and press ENTER in PTZ Control Mode first. Then, press Enter to run P/T/Z/ Motion Mode in the PIP screen and press Enter again to cancel P/T/Z/ Motion Mode. Press Enter at the Position Name position to see Virtual Keyboard. Type Position Name and press OK to save Position and Position Name.
Press the SET button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to select Camera Menu. TELE WIDE VIEW PRESET Press the SET button in front of SHR-4160N/P to return to the upper menu from SET button Camera Menu.
SHR-4160N/P USER’S MANUAL Preset View Preset setup allows your movement to a certain saved position of PTZ device. Press the VIEW button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to select Preset. TELE WIDE VIEW PRESET...
Other View Press the VIEW button in front of SHR-4160N/P in Single Screen PTZ device Control Mode to supply PTZ device. This is a very special function. Note Note Samsung, Pan., Pel.-P, or Pel.-D Protocol PTZ device supplies this function.
SHR-4160N USER’S MANUAL PANIC (Emergency Recording) Pressing the button records all the images input so far. Emergency Record has the characteristics of CIF size, Very High resolution, and 15ips(NTSC)/12.5ips(PAL). During PANIC Recording, LED lights on and a recording icon appears on the screen. During recording in HDD, HDD LED in front blinks. During PANIC Recording, you may stop PANIC Recoding by pressing the button then LED lights out.
REC (Normal Recording) Pressing REC the button starts recording as set in Record Mode of MENU. Then, REC LED lights on and a recording icon appears on the screen. During recording in HDD, HDD LED in front blinks. During REC Recording, you may stop REC Recoding by pressing the REC button then REC LED lights out.
SHR-4160N USER’S MANUAL Record Schedule While “Continuous Recording” or “Both” is selected for Record Schedule in MENU, Timer Recording automatically starts. Otherwise, Timer Recording remains inacti- vated. During Timer Recording, Recording Icon appear on the screen. During recording in HDD, HDD LED in front blinks. During the event recording, the auto recording is operated when the event occurs.
Event Recording Alarm Detection Sensor State in Event Record Alarm of MENU shall be set to N.O (Normal Open) or N.C (Normal Close) Motion Detection M.D State in Event Record Motion Detection of MENU shall be set to On. Video Loss Detection Image Loss State in Event Record Image Loss of MENU shall be set to On.
SHR-4160N USER’S MANUAL Before Use Pressing the SEARCH button shows Search Menu on the screen as seen above. CALENDAR uses a calendar to search video files at the preset time. Event Search searches video files recorded by Event. Date/Time inputs a day and time on which the system searches video files. Go To First searches video files from the oldest one.
Calendar Search Be sure to designate both the channel and the date first. Then press [Start] button to initiate search. Uses a calendar to search video files at the preset time. Four channels as a maxi- mum are in the range of search. Press [Enter] ➛,and ❿¤to choose 4 channels as a maximum and the date column with recorded video image will turn blue.
SHR-4160N/P USER’S MANUAL Event Search Searches Normal Recording, Panic Recording, Sched.(Schedule) Recording, Alarm Recording, Motion Recording, and Image Loss Recording by the time. You shall select a channel to search to see the Event information of the channel. On the basis of the Event information for each channel, the system searches the video file for the event.
Date/Time Search Use the Day/Time information to search video files at the time as you desire. Up to 4 channels can be searched at once. Press , ❷, and [Enter] to select a channel and the box on the right of the chan- nel will be checked.
SHR-4160N/P USER’S MANUAL Go to First Search Searches the oldest one among recorded video files. Up to 4 channels can be searched at once. , ❷, Press [Enter] to select a channel and the box on the right of the channel will be checked.
Go to Last Search Searches the latest one among recorded video files. Up to 4 channels can be searched at once. , ❷, Press [Enter] to select a channel and the box on the right of the channel will be checked. Press [Start] to start searching and press [Cancel] to return to the previous menu.
SHR-4160N/P USER’S MANUAL Play ❿ ¤ II Press the PLAY/PAUSE button( ) to play the data recorded in HDD. This chooses out a channel with the oldest data among recorded channels and plays the data from the first part of the channel. If you used the SEARCH button for play just before, the system would remember the information of the played ❿...
Page 99
Play Screen Mode Definition Single Screen PIP Screen 9 Split Screen 16 Split Screen 4 Split Screen 16 Split Screen PIP Screen Single Screen 4 Split Screen 9 Split Screen Whenever you press [Mode], the Play screen becomes 4Split, Single, PIP, 9Split, 16Split in turn. If you select only one channel from Searh, the 4 Split screen will not appear.
Page 100
SHR-4160N/P USER’S MANUAL Play at Faster Speed ❿ ❿ If you press the LEFT or RIGHT button( ➛ ➛ ) or use the Shuttle during play, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or reversely.
If you change the system time or terminate the system, the current backup process will be paused. 1.3 Backup Play Press the SEARCH button in front of SHR-4160N/P and press the Backup Search menu to play backup. To search backup, select the device.
Page 103
If you change the system time or terminate the system, the current backup process will be paused. 1.3 Backup Play Press the SEARCH button in front of SHR-4160N/P and press the Backup Search menu to play backup. To search backup, select the device.
Page 104
USB memory device with one partition. In addition delete the USB memory at SHR-4160N/P for safe backup(refer to 5-7, System Information and Setup.). 5. When you connect the backup device to SHR-4160N/P, it takes some time for SHR-4160N/P to recognize the backup device. Consequently, connecting the backup device to SHR-4160N/P and executing backup may not result in the con- nection of the device.
Backup Search 1. Backup search menu 1-1. External HDD Search If you select an external HDD, you may search the data by using Date, Event, Origin, or Late. Refer to p8.2~p8.5 for this purpose.
Page 106
SHR-4160N/P USER’S MANUAL 1-2. USB Device Search Select an external USB device to search a date. Use the weekday/time information in the backup image to search images contained in as many as 4 channels. Click , ❷, [Enter] to select a channel and the box on the right of CH No.
SHR-4160N/P USER’S MANUAL Introduction Smart Viewer is a program that a general PC user is able to install SHR-4160N/P to his PC to monitor the search video and audio data through Network without going to the site where SHR-4160N/P is installed by himself.
One DVR set allows 3 Smart Viewer users(or 6 with Multicast) at the same time. With a Smart Viewer, you are allowed to connect to as many as 9 SHR-4160N/P to monitor them simultaneously. Smart Viewer is optimized in the resolution of 1024X768...
VGA RAM 32Mb or higher DirectX 8.1 or higher Note Note Depending on Recording Rate, Video Size, and user’s PC specification set to SHR-4160N/P, the number of Smart Viewer play frame varies. For the detailed specification, refer to Appendix 5. 10-3...
Smart Viewer Installation Smart Viewer Installation Put a Smart Viewer Program CD in and open the “Smart Viewer” folder in CD. Run the “Setup.exe” file. 10-4...
Page 112
SHR-4160N/P USER’S MANUAL Click the “Next” button. If you agree with Smart Viewer License, click “Yes”. Designate a folder to install Smart Viewer in it and click “Next”. 10-5...
Page 113
The system proceeds with setup file installation and system setup. Installation is complete. Press “Finish” to terminate installation. 10-6...
@ This button terminates or minimizes the program. # It displays the current date, day, and time. $ This button is used for the connection with the preset DVR(SHR-4160N/P) or site. % This screen shows the monitoring video image. ^ These buttons are used to select the window to display event messages and came connection condition.
4160N/P)s as you approaches at the site. Connection Failure Cases 1. Password Certification Failure - In case of discord between the Network password set to SHR-4160N/P and the connection password set to Smart Viewer, a window pops up to induce retry of password input.
Page 117
No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to access SHR-4160N/P simultaneously. One SHR-4160N/P allows as many as 3 users, 1 Admin and 2 Users for simultaneous connection(or as many as 6 users including 5 Users for Multicast).
Page 118
SHR-4160N/P USER’S MANUAL Time Information - As soon as you are Connected to SHR-4160N/P, the date, weekday, and time of the set to which the selected channel is connected. - If SHR-4160N/P is not connected, the present date, weekday, and time of the user's PC are displayed.
Page 119
: Alarm Event Note Note ^ If you connect and set up PTZ device in SHR-4160N/P, PTZ controllability of the channel will be displayed. Select a channel capable of PTZ and use the PTZ related buttons at the bottom to control PTZ.
Page 120
Setup Start / End (Local) : Start/Finish the Menu screen at SHR-4160N/P. Video Loss CH[N] : Video Loss at the N channel of SHR-4160N/P encountered. Alarm Detection CH[N] : Alarm issued at the N channel of SHR-4160N/P.
Page 121
- List displays the connection condition of DVR and CAMERA. Note Note [DVR Icon Mark] If you succeed in SHR-4160N/P connection, the icon will be turned yellow, other- wise black. [DVR Icon Mark] During monitoring by connecting with CAMERA, it will turn yellow.
Page 122
1,2,3,4 (CH) - In Nine-Split Mode : 1,2,3,4,5,6,7,8,9 10,11,12,13,14,15,16 1,2,3,4,5,6,7,8,9 (CH) Note Note If you connected with multi-DVRs(SHR-4160N/P) through a site, Sequence will operate as follows. - In Single Mode : DVR1:1CH DVR1:16CH DVR2:1CH DVR1:1CH - In Quad Mode : DVR1:1,2,3,4CH...
Page 123
: During monitoring in Quad Mode : During monitoring in Single Mode : Camera Off Note Note The figure in a screen icon indicates the screen position in SmartViewer. : The orange icon indicates the current channel is connected to a camera. : The gray icon indicates the channel is connected to a camera but not displayed on the screen.
Page 124
- In Nine-Split Mode : 1,2,3,4,5,6,7,8,9 10,11,12,13,14,15,16 1,2,3,4,5,6,7,8,9 (CH) Note Note If you connected with multi-DVRs(SHR-4160N/P) through a site, Sequence will oper- ate as follows. - In Single Mode : DVR1:1CH DVR1:16CH DVR2:1CH DVR1:1CH - In Quad Mode : DVR1:1,2,3,4CH...
Page 125
FAVORITE Button - Click the FAVORITE button to activate the FAVORITE window. Click the current FAVORITE to display all the cameras recorded in the settting. You may delete all the selected FAVORITE settings or all the FAVORITE settings. You can select a new FAVORITE number and name. Alters FAVORITE at the selected intervals.
Page 126
SHR-4160N/P USER’S MANUAL Video Recording Button - If you select a channel in play and click the REC button, the image will be saved in a file format with the extension of .dvr in a designated folder of your PC.
Page 127
ZOOM IN / OUT will be acti- vated in the clicked part. Note Note The PAN / TILT / ZOOM function is supplied to all camera. But, POWER ZOOM is supported only by Samsung Smart Dome Camera, with TILT below 45°. 10-20...
Page 128
The name of @,#, and $ functions varies depending on the camera and some cam- eras does not support any of those functions. - The Samsung camera supports all the functions and names. - The Panasonic camera supports all the functions, but with different names.
Page 129
The Camera Menu Setup function is supported by Samsung and Panasonic. Caution Caution As far as SHR-4160N/P uses the PTZ device control related functions, Smart Viewer can not control PTZ device. The PTZ device control related functions are authorized with the user with Admin authority.
Search Mode Description of Search Mode Initial Screen - Search Mode is divided into Remote Mode for SHR-4160N/P image search/play and Local Mode to play .dvr file saved in the directory designated by your PC. ! Pressing this button enters Search Mode for the remote control of the image recorded in SHR-4160N/P.
Page 131
DVR(SHR-4160N/P) Selection/Change by SITE - Choose out a SHR-4160N/P from the connection list for search. - SHR-4160N/P turns black if connected with the authority of ADMIN and gray with the authority of USER. - Search function is for administrator only.
Page 132
SHR-4160N/P USER’S MANUAL Calendar Window - If the video data in on-line SHR-4160N/P was recorded, the date turns red. - If you click the date in red, the saved video data will be displayed. - The currently selected date will be marked with a thick red box.
Page 133
Video Record / Convert File / Print / Setup ! Video Record Button - If you select a channel in play and click the SAVE button, the image will be saved in a file format with the extension of .dvr in a designated folder of your - The name of the directory in which an image will be saved, the file name, and the length of an image to be saved shall be set up by Setup Mode Viewer...
Page 134
SHR-4160N/P USER’S MANUAL # Print - This function outputs the screen zone of the image in play which is now being displayed. $ Setup Mode Button - This button pops up the Setup Mode window. Play Buttons ! Play : Play...
Page 135
Local Mode is not permitted. Click the Stop button first before conversion. Time Line - Displays the time information on the video data in SHR-4160N/P on the calendar window for the selected day. - The General mode indicates the 24 hour information from 0 o’clock to 24 o’clock while the Zoom mode indicates the time information every 2 hours.
Page 136
- This mode plays .dvr files recorded in the directory of your PC by the Record function. - You can search and play only one channel. - You are free for access to the user being connected to SHR-4160N/P - Other functions than the calendar display function are as same as those of Remote Mode.
SETUP MODE Description of Initial Screen ! This button is used to select items for DVR Setup, Viewer Setup, Site Setup, and S/W Version setup. @ Shows what the selected Setup item can set up in detail. # This button terminates the Setup window. $ This button saves the information revised in the Setup window, remarks the infor- mation prior to such a revision, or terminates the Setup window.
Page 138
- Viewer Setup : Viewer Setup allows you to set up various kinds of items concern- ing operations of Smart Viewer. - Site Setup : Site Setup allows you to set up SHR-4160N/P information, that is SHR-4160N/P name, IP Address, ID, and Password that you contact through Smart Viewer or register all the registered SHR-4160Ns at a site for control.
DVR Setup - Click the [DVR Setup] button for DVR Setup. - You can change the setup items of SHR-4160N/P Menu, being connected with Smart Viewer remotely. - DVR Setup is composed of 5 items, System, Camera/Audio, Monitoring, Recording, and Network.
Page 140
- Information Information shows the information on on-line SHR-4160N/P. SHR-4160N/P Note Note For the detailed items of DVR Setup, refer to Chapter 5, MENU. - Password Password determines the password for the control of SHR-4160N/P Menu or SHR-4160N/P key input. 10-33...
Page 141
- If you change the Date/Time value, SHR-4160N/P will automatically cut the connection with Smart Viewer to apply a new time setup. - Upon completion of new time setup of SHR-4160N/P, you are permitted to resume connection with Smart Viewer.
Page 142
SHR-4160N/P. In short, the language setup of Smart Viewer does not change. Language specification to be supported is subject to change later. - Disk Mode In Disk Mode, you may set up Writing Mode of HDD attached to SHR-4160N/P. 10-35...
Page 143
- Remocon (Remote Control Device) Remocon can set up Remote Control Device fixed to SHR-4160N/P. Note Note If you fix Remote Control Device to the main body of SHR-4160N/P and activate the setting values, Viewer will be disabled to control PTZ. 10-36...
Page 144
@ Camera - Config. Config. sets up Video, Audio On/Off, Camera Title, and Screen change Time for each channel of on-line SHR-4160N/P. Caution Caution - Title supports English only. If you type in and apply Title in your native language, Warning message will pop up to ask your retyping.
Page 145
- PTZ device If a dome camera is connected to all channels, sets up Camera ID, Protocol, Baud Rate, Parity, Data Bit, Stop Bit, and Serial Mode. # Monitoring - Monitoring Monitoring sets up both Event Monitoring and OSG Display of Live Mode. 10-38...
Page 146
SHR-4160N/P USER’S MANUAL $ Recording - Rec. Mode Rec. Mode sets up Live Mode decision, Video Size during recording, Quality, and Rate. NTSC Note Note Full D1(L) Video Size does not support 15ips, 10ips(NTSC) / 12.5ips, 8.33 ips(PAL) - Event Rec.
Page 147
- Alarm Rec. Alarm Rec. sets up the information necessary for Alarm Recording. Note Note At least one camera should be selected in advance to be coupled with Alarm. - Motion Rec. Motion Rec. sets up the information necessary for recording by Motion Detection.
Page 148
SHR-4160N/P. % Network - Password This sets up the password for Admin and User to let you connect with SHR-4160N/P through Network in Smart Viewer. Caution Caution - Network Password shall be composed of no more than 8 texts. - If you leave Password blank and apply it, Warning message will pop up to ask your retyping.
Page 149
Sets up the network Bandwidth. Please adjust the bandwidth to the network con dition in which SHR-4160N/P is connected. Sets up IP Address, Gateway, Subnet Mask, and DNS. Please input both ID and password of the sub scriber in the event of ADSL.
Page 150
SHR-4160N/P USER’S MANUAL Callback - Sets up the Callback functions of SHR- 4160N/P. - Sets up the IP address and port to which SmartViewer was installed to deliver the Callback message in the event of Alarm, Motion Detection, or Video Loss.
- A PORT number is flexible and 4 numbers in a row will be changed in all. (554,555,556,557 558,559,560,561) - You shall allocate the above ports for SHR-4160N/P if you want to compose a net- work by IP Router. Viewer Setup - Click the [Viewer Setup] for Viewer Setup.
Page 152
+ Date”. @ Location 4160N/P - As long as you are connected to SHR-4160N/P in Monitoring or Search Mode while recording the video data in display, this sets up a directory where .dvr file format will be saved. - The current default directory is “Smart Viewer Program Installed Directory \video\dvr”.
Page 153
- Determines if Smart Viewer shall be automatically connected to SHR-4160N/P or Site as soon as it starts running. - If you check “Auto Connection On”, the name of SHR-4160N/P and Sites that are currently registered in DVR/Site List will be listed as follows and if you select one, it will be automatically connected to the selected SHR-4160N/P or Site as soon as Smart Viewer starts running.
Site Setup - Click the [Site Setup] button for Site Setup. - Site Setup sets up the information on DVR(SHR-4160N/P) or Site that you want to contact by Smart Viewer. - Smart Viewer allows you to contact DVR(SHR-4160N/P) or Site registered here.
Page 155
DVR List - DVR List sets up the information on DVR(SHR-4160N/P) that you want to contact by Smart Viewer. - You may register a new DVR(SHR-4160N/P) or delete and edit the DVR (SHR-4160N/P) selected from the registered list and the name and IP / MAC Address of the registered DVR will be enlisted in DVR List.
Page 156
1. Network Modes - LAN - If DVR(SHR-4160N/P) is connected to LAN, set Network Modes to LAN. - If the LAN connected to DVR(SHR-4160N/P) uses Static IP, select Static IP from Address Type and input the name and IP Address of DVR(SHR-4160N/P).
Page 157
2. Network Modes - ADSL - If DVR(SHR-4160N/P) is connected to ADSL, set Network Modes to ADSL. - If the LAN connected to DVR(SHR-4160N/P) uses Static IP, select Static IP from Address Type and input the name and IP Address of DVR(SHR-4160N/P).
Page 158
@ Deletion of Already-Registered DVR(SHR-4160N/P) - If you select one DVR(SHR-4160N/P) in DVR List for deletion and press the [Delete] button, the following message box will pop up. If you press [OK] button then, DVR(SHR-4160N/P) will be deleted.
Page 159
# Modification of Already-Registered DVR(SHR-4160N/P) - If you select one DVR(SHR-4160N/P) in DVR List for modification and press the [Modify] button, the following message box will pop up. If you press [OK] button then, DVR(SHR-4160N/P) will be modified. - As long as DVR(SHR-4160N/P) for modification is connected with the current Smart Viewer, the following message box will pop up and DVR(SHR-4160N/P) will not be modified.
Page 160
SHR-4160N/P USER’S MANUAL Site List - Site List registers multi- DVRs(SHR-4160N/P) that you want to contact at once by Smart Viewer at one site for control. You are allowed to register a new Site or delete or modify the selected Site from the registered list and add...
Page 161
@ Deletion of Already-Registered Site or DVR(SHR-4160N/P) - If you select one Site or DVR(SHR-4160N/P) in Site List for deletion and press the [Delete] button, the following message box will pop up. If you press [OK] button then, either Site or DVR(SHR-4160N/P) will be deleted.
Page 162
Modification to DVR(SHR-4160N/P) shall be done only in DVR List. DVR(SHR-4160N/P) Addition to Site - If you press the [Add] button, DVR(SHR-4160N/P) selected from DVR List will be added to the Site selected from Site List. Site addition to DVR(SHR-4160N/P) set to ADSL is prohibited.
Page 163
DVR(SHR-4160N/P), your access will be denied. ! Smart Viewer Version and system requirements will be displayed. @ Here displays the version and name of DVR if any DVR(SHR-4160N/P) is being connected with Smart Viewer. You are also able to upgrade DVR(SHR- 4160N/P) S/W by transmitting it to on-line DVR(SHR-4160N/P).
Page 164
- Smart Viewer Version and system requirements will be displayed. DVR Version SHR-4160N/P - DVR Version not only displays the connected DVR(SHR-4160N/P) name if any DVR(SHR-4160N/P) is being connected with Smart Viewer or the name of DVR(SHR-4160N/P) composing a site if any DVR(SHR-4160N/P) is being connected with the site but also displays DVR(SHR-4160N/P) S/W version.
Page 165
@ Click the following button to open the “SHR-4160N/P Firmware” file in tgz format. SHR-4160N/P Smart Viewer SHR-4160N/P # Press the [Upgrade] button to transmit a file to the selected DVR(SHR- 4160N/P) and start upgrade of DVR(SHR-4160N/P) S/W. $ The progress of file transmission and upgrade will be displayed at the bottom.
SHR-4160N/P USER’S MANUAL Introduction In SHR-4160N/P, you can back up the video data by using External HDD, USB Memory, and CD. In the Backup Viewer, the backup image data can be searched or played in the PC through the CD/DVD or connecting the external HDD, USB Memory to the user’s PC.
Features The video data backed up in any method among External HDD, USB Memory, and CD can be searched or played in your PC. Backup Viewer is optimized in the resolution of 1024 x 768. 11-2...
SHR-4160N/P USER’S MANUAL PC Specification(Recommendation) OS: Windows 2000, Windows XP Recommendation : - CPU Pentium 3 1GHz or higher - RAM 256Mb or higher - VGA RAM 16Mb or higher - Direct X 8.1 or higher 11-3...
SHR-4160N/P USER’S MANUAL Initial Screen of Backup Viewer Description & ! Terminates or minimizes the program. @ Displays the current date, weekday, and time. # Selects a device(External HDD, USB Memory, or CD/DVD) for connection. $ Displays the image in play.
Using Backup Viewer Connecting Connecting means you may access and search the video data recorded in External HDD, USB Memory, or CD/DVD installed in your PC. Select a device that you wish to connect and click the Connecting button. Connecting Screen Display of Time - Displays the date, weekday, and time of your PC.
Page 177
SHR-4160N/P USER’S MANUAL Display of Connection - When connected to the device installed in your PC, the Connecting button indicates the connecting condition. - Click the Connecting button for disconnection. Display of Play Screen OSD Displays the CH number and replay time.
Page 178
Calendar Window - The date when the video data was recorded in the current device is displayed in red. - Click the red colored date to display the video information in Timeline. - A thick red box will be displayed in the current date. - ¦...
Page 179
SHR-4160N/P USER’S MANUAL Play Buttons ! Play @ Reverse Play # Stop $ Fast Forward % Fast Backward ^ Step Forward : Forward by 1 second & Step Backward : Backward by 1 second * Go to Last : Plays the first image of Timeline.
Page 180
Timeline - Displays the time when the video image was recorded in the current device for the date selected from the Calendar window. - The General mode displays the information for 24 hours from 0 to 24 o’clock and the Zoom mode displays the time information every 2 hours. [General Mode] ! This mode is displayed in the Play screen and the CH will be activated in the white background.
Page 181
SHR-4160N/P USER’S MANUAL Next Button - Displays the next channel. Note Note Channel change is not available in the process of (Play/Reverse Play/Fast Forward/Fast Backward). 11-15...
SHR-4160N/P USER’S MANUAL Product Specification Item Specification Remark 32bit RISC CPU Memory SDRAM : 128MByte Flash : 16 MByte Operation System Embedded OS Broadcasting NTSC System Input Voltage AC 110-220V(NTSC) / 100-230V(PAL) Power Comsumption 85 Watt Max Composite 16 Channel - 1.0Vp-p...
Page 185
NTSC : 1ips/3ips/5ips/7.5ips/10ips/15ips PAL : 1ips/2.5ips/5ips/6.25ips/8.33ips/12.5ips * Packing ATA HDD x 4(MAX) 160GB Internal -Primary/Secondary IDE Connector (Samsung) -MAX HDD Size : 250GB x 4 = 1Tera Byte x 1EA Storage IEEE1394 HDD Capacity -MAX 6 (Daisy chain connection) -MAX HDD Size : 250GB x 6 = 1.5Tera Byte...
Page 186
SHR-4160N/P USER’S MANUAL Item Specification Remark Calendar Event - Normal, Panic, Schedule, Alarm, Motion, Search Mode Video Loss Date/Time Go to First Go to Last Backup Data Resolution Decoding Performance Resolution & Play Back Performance 15ips(NTSC)/12.5(PAL) 15 ips/1Ch Half D1 15ips(NTSC)/12.5(PAL) 15 ips/1Ch...
Factory Default This restores the Network information and preset values in SHR-4160N/P to the original state at the time of factory shipment. Factory Default will be done if you; - Use System / Load Factory Default in MENU or, - If you hold on to the Mode button in Live Mode and keep pressing the CH5 button for 5 seconds, the system will return to the Factory default condition.
Page 190
SHR-4160N/P USER’S MANUAL Classification Detailed Items Factory Setup Duration Event Monitoring Date OSD Display Time Monitoring Setup Title Status Spot Out Channel Spot Out Event Monitor Monitor Out Composite Out PB Channel Position Right Down Mode Record Mode Video Size...
SHR-4160N/P is connected with a fast network like LAN. When the main body of SHR-4160N/P is connected with a slow network like ADSL, the play speed will be 0.5 Frame/sec. In addition, the above specification has been defined to the recommended specification of your PC.
SHR-4160N/P DVR. 6. You cannot enter MENU by forgotten password. - If you forget the password, you shall reset SHR-4160N/P DVR to the values set at the factory. Keep pressing both the "MODE" button and the "5" button on the left for 5 seconds until LED lights on in the order of 1 5.
Page 194
HDD. 12. You cannot connect to SHR-4160N/P DVR through Smart View. - Check if 3 Smart Viewer users are in connection with SHR-4160N/P DVR. SHR-4160N/P DVR allows no more than 3 users’ connection with Smart Viewer at a time.
Page 195
5 times. If it remains unconnected after 5 time trial, it will automatically give up connection. - As far as SHR-4160N/P DVR is connected to the ADSL network, you may be dis- connected from Smart Viewer when the network conditions goes bad.
Page 196
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.