DLS T3FS-25S Assembly Instructions

Stands for T3 Home cinema speakers
Welcome
Thank you for buying a DLS stand for our T3 Home cinema speakers.
They come in three models:
- T3FS-25S 25 cm (9,8") stand for T3 tower
- T3FS-89S 89 cm (35") stand for TS3 / TM3
- T3FS-109S 109 cm (43") stand for TS3 / TM3
Parts included
- Base stand with speaker terminals (5)
- Supporting tube (25 cm, 89 cm or 109 cm)(4)
- Fix screw (3)
- Connecting adaptor (2)
- Connect screw M8 (1)
- Nut for base stand/tube (6)
- Speaker cable with connectors (not in T3FS-25S)
Assembly instructions T3FS-89S & T3FS-109S
1. Unpack all parts
2. Push the speaker cable through the tube (4) as in fig. 2.
3. Attach the tube to the base with the big nut (6). The cable goes
through the nut. Turn the tube with the hole backwards.
Connect the speaker cable to the terminals under the base. Use the
cable with the printing as + and connect to the red terminal on the base.
The other cable as - to the black terminal. (Fig. 3)
4. Fasten the small M8 connecting screw (1) into the connecting adaptor (2).
5. Fasten the connecting adaptor (2) to the speaker bottom plate. There
is a screw thread in the speaker bottom plate.
6. Push the connecting adaptor (2) into the supporting tube(4) and fas-
ten in the correct direction (see fig. 1) with the fix screw (3).
7. Connect the speaker cable to the speaker terminals, observe polar-
ity. Cable with printing to red terminal (+).
8. Now the speaker is ready for use.
NOTE!
Early models of TS3/TM3 has no thread in the bottom plate.
The bottom plate can be exchanged to a new one with thread.
Part numbers for these bottom plate are:
10-17110 (silver)
10-17120 (black)
Assembly instructions T3FS-25S
1. Unpack all parts
2. The base has to be removed from the T3 speaker (fig. 4)
3. Pull out the cable through the holes in the T3 bottom plate
4. Fasten the M8 connecting screw (1) into the connecting adaptor (2).
5. Fasten the connecting adaptor (2) to the speaker bottom plate. There
is a screw thread in the speaker bottom plate.
6. Push the connecting adaptor (2) into the supporting tube (4) and
fasten in the correct direction (see fig. 1) with the fix screw (3).
7. Push the speaker cable through the tube as in fig. 2.
8. Attach the tube to the base with the big nut.
Connect the speaker cable to the terminals under the base. Use the
cable with the printing as + and connect to the red terminal on the base.
The other cable as - to the black terminal. (fig. 3)
9. Now the speaker is ready for use.
NOTE!
Early models of T3 has no thread in the bottom plate. The speaker
cable inside the T3 is also too short.
The bottom plate can be exchanged to new one with thread.
Part numbers for this bottom plate is:
10-17110 (silver)
10-17120 (black)
A hole for the cable must be drilled in the bottom plate.
The speaker cable inside the T3 is also too short and must be extended
with a piece of extra wire.
In case you have the first model of T3, ask your dealer to help you to
attach the stand to your speaker.
Assembly instructions
Fig. 1
Fig. 2
(6)
Fig. 3
Fig. 4
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
T3FS-25S
T3FS-89S
T3FS-109S
(1)
(2)
(3)
(4)
(5)