DLS BRUXT20 Manual

Thank you for buying DLS T20 tweeters. The T20 tweeters are included
in the DLS PRO slimline and REFERENCE series speaker kits.
They can also be bought separately for use as "Tune-up speakers" to
improve the treble in any other system. In this case you must use a
separate tweeter filters with art. no 9-25604. Connect as in the lower
drawing.
MOUNTING:
T20 can be mounted on the dashboard with the angled cup (2) or the
plain mounting plate (3), or recessed in a doorside with the flush cup (4).
1
SURFACE MOUNTING:
For straight surface mounting use only the
plain mounting plate (3). Fasten with two
screws.
For angled surface mounting use the plain
mounting plate (3) together with the angled
cup (2). The plate is attached to the cup
with two small screws. The tweeter ele-
ment (1) is attached to the cup by fitting
the three wings into the tracks of the cup
and then twist it clockwise.
1
9
FLUSH MOUNTING:
Drill a hole with a diameter of 51 mm. Put the two metal wings (6)
through the two tracks (7) in the center of the cup, just as the picture
shows, and attach them with the M4 screw and nut (8) through the
center hole. The cup is attached to the door side when the metal wings
are pressed to the back side of the door.
Put the tweeter element into the cup with the cable going out through
the bottom hole (9). Then attach the element by putting the ring (5) into
the space between the cup and the element.
FACTS ABOUT DLS T20 TWEETER
Size
Nom. power (RMS)
Freq. range
Sensitivity
X-over frequency
Magnet diameter
Mounting depth
Mounting hole
Cone material
If you have any questions about this product, contact
your local dealer or DLS customer support center.
DLS Svenska AB
P .O. Box 13029
SE-402 51 Göteborg, Sweden
Tel. +46 31 840060
Fax +46 31 844021
E-mail: info@dls.se
www.dls.se
DLS T20 TWEETER
2
7
4
6
8
DLS T20
20 mm
50 Watts
1,5 kHz-20 kHz
93 dB
3,5 kHz with cable filter 9-25604
26 mm
20 mm (recessed mounting)
51 mm (recessed mounting)
Silk
THE KIT CONTAINS:
q
2 pcs 20 mm swivelball head tweeter elements
q
Mounting accessories for dash-
and recessed mounting
FILTER CONNECTION
T20 connected to a PRO slimline or REFERENCE
2-way system.
3
Bass/mid
Tweeter
T20 connected to any other speaker
system:
5
A separate tweeter filter must be used. This cable filter
(art.no 9-25604) is only included when T20 is bought as
a tune-up speaker for other systems.
Speaker
impedance 4
Car stereo / amplifier
Speaker connection and tweeter level
select:
The cable filters coming with this tweeter (when bought as a
tune-up speaker) should be connected in series with
respective speaker element as on the drawing. Select tweeter
level by connecting the red cable to either the red or yellow
cable coming out from the filter box. If the tweeter is directed
towards the listener, low level is to be prefered. Otherwise
make your own tests for best result.
Sometimes the midrange can be improved by phase reversing
the tweeter. Try it and judge yourself. The tweeter level select in
PRO slimline and REFERENCE is made iside the black filter
box by moving a small jumper.
NOTE! Filters must be used. If the tweeters are
connected without filters they will be damaged and
sound reproduction becomes bad.
Black -
Low-pass filter
Blue +
(if used)
Tweeter filter
Red
9-25604
Yellow
Tweeter level select:
Tweeter T20
Red to red = high
Red to yellow = low
Bass/mid
Black -
Red +