Basic Operations; Adjusting The Tone - Clarion HX-D2 Owner's Manual

Basic Operations

Turning on/off the display
You can turn the display ON/OFF by holding the
[A-M] button down for at least one second.
You can also turn the display ON by pressing the
[DISP] button while the display is OFF.

Adjusting the tone

Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes in the following order:
∗ "BASS" and "TREB" are displayed when "BASS/
TREB" are selected at EQ SELECT.
GWhen "STD" is set
➜ "BASS"
∗1
"SW-VOL"
"BAL" ➜ "FADER" ➜ Last function mode.
GWhen "DIRECT" is set
"N-FAD VOL" ➜ "BAL" ➜ "FADER" ➜
Last function mode.
GWhen "MULTI" is set
➜ "BASS"
∗1
"SW-VOL"
"BAL" ➜ Last function mode.
∗1
The item can be adjusted when the sub-woofer
setting is not set to "OFF".
∗2
The item can be adjusted when "EQ SELECT" in
the Adjust mode is set to "BASS/TREB".
Adjusting the volume of sub-
woofer/non-fader output
These items can be adjusted when the sub-
woofer/non-fader setting is "ST" (stereo) or
"MONO" (monaural).
∗ The factory default setting is "0.0 dB".
1. Press the [A-M] button to select "SW-VOL"
or "N-FAD VOL".
∗ Select "SW-VOL" when the Audio mode is the
Standard mode or the Multi mode, and "N-
FAD VOL" when the Audio mode is the Direct
mode.
2. Press the [ ] or [ ] button to set the output
volume.
∗ The adjustment range is -10.0 dB to +10.0 dB
(0.5 dB steps).
3. Press the [A-M] button several times to
return to the previous mode.
12
HX-D2
➜ "TREBLE" ➜
∗2 ∗2
➜ "TREBLE" ➜
∗2 ∗2
Adjusting the bass/treble
This function is used to set the tone in more
detail for listening.
• The tone can be adjusted when the Equalizer
mode is set to "BASS/TREB".
∗ This can be adjusted when the Audio mode is the
Standard mode or the Multi mode.
∗ The factory default setting is "0 dB".
1. Press the [A-M] button to select "BASS" or
"TREB".
2. Press the [ ] or [ ] button to adjust the
output volume.
∗ The adjustment range is -12 dB to +12 dB
3. Press the [A-M] button several times to
return to the previous mode.
Adjusting the balance/fader
• "FADER" (fader) can be adjusted when the
Audio mode is the Standard mode or the
Direct mode.
∗ The factory default setting is "0".
1. Press the [A-M] button to select "BAL" or
"FADER".
2. Press the [ ] or [ ] button to adjust the
volume.
GAdjusting the balance (volume of the left
and right speakers)
To enhance the left side, press the [ ] button.
To enhance the right side, press the [ ]
button.
∗ The adjustment range is L13 to R13.
GAdjusting the fader (volume of the front
and rear speakers)
To enhance the rear side, press the [ ] button.
To enhance the front side, press the [ ]
button.
∗ The adjustment range is R12 to F12.
3. Press the [A-M] button several times to
return to the previous mode.