Table of Contents
Advertisement
Quick Links
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools described
before.
A
SUS G1S Series Notebook consists of various modules. This chapter describes the
procedures for the complete notebook disassembly. In addition, in between procedures,
the detailed disassembly procedure of individual modules will be provided for your service
needs.
The disassembly procedure consists of the following steps:
• Battery Module
• CPU Module
• Memory Module
• HDD Module
• Optical Drive Module
• Keyboard Module
• Top Case Module
• LCD Module
• Motherboard Module
• WLAN Module
2 - 1
Disassembly procedure
2
Chapter
Advertisement
Table of Contents
Related Manuals for Asus G1S
Summary of Contents for Asus G1S
-
Page 1: Disassembly Procedure
Be sure to use proper tools described before. SUS G1S Series Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs. -
Page 2: Battery Module
Disassembly procedure Battery Module B A T T E R Y The illustration below shows how to remove the battery module. Remove battery module 1．Slide the battery latch 1 to open battery lock 2．Slide the battery latch 2 and pull the whole battery away from the system. CPU Module C P U M O D U L E... - Page 3 Disassembly procedure 2. Remove the Mylar. 3. Remove 4 screws (M2*5) aside the CPU. And take away the heat sink.. M2*5 4. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU. 2 - 3...
-
Page 4: Removing Memory Module
Disassembly procedure 5. Squeeze the vacuum handling pump and use it to lift the CPU away. M E M O R Y Memory Module M O D U L E The illustration shows how to remove the memory module form the notebook. Removing Memory module M E M O R Y 1. -
Page 5: Wlan Module
Disassembly procedure WLAN Module W L A N The illustrations below show how to remove the WLAN module from the notebook. M O D U L E Remove WLAN module 1. Disconnect 3 antenna cables, remove 1 piece of tape and remove the antennas out of cable guide; then unlock two latch and take WLAN out of system;... -
Page 6: Hdd Module
Disassembly procedure HDD Module H D D The illustrations below show how to remove the HDD module from the notebook. M O D U L E Removing HDD Module H D D 1. Remove 2 screws (M2*5) here, open HDD door by the tweezers and then take away the HDD M O D U L E door. -
Page 7: Keyboard Module
Disassembly procedure Keyboard Module K E Y B O A R D The illustration of below shows how to remove the keyboard Removing Keyboard 1. Remove 2 screw (M2*5) here, and then turn over the notebook. 2. Push the 3 latches in (F1, F8, Ins) with a pair of tweezers or a single-slotted screwdriver and lift the keyboard plate up. - Page 8 Disassembly procedure 4. Disconnect the FPC connector by a pair of tweezers and then remove the keypad plate. Removing Keyboard Cable 1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1). 2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers. 3.
- Page 9 Disassembly procedure 2. Remove the both hinge covers. 3. Remove 2 screws in hames cover, then take the hames cover away. 4. Remove 1 piece of tape fixing the table and then remove 1 screw here, and disconnect the LCD cable 2 - 9...
- Page 10 Disassembly procedure 5. Remove 1 screw here, and disconnect the cable. 6. Remove 2 screws on both end 7. Remove 2 screws beside the system. 2 - 10...
-
Page 11: Lcd Module
Disassembly procedure 8. Open one latch before LCD and then separate LCD module from system. 9. Disconnect the touch pad cable with pair of tweezers. LCD Module L C D M O D U L E The illustrations below show how to remove and disassemble the LCD module. The module contains LCD panel, Inverter board, LCD bezel, LCD back cover. - Page 12 Disassembly procedure 2. Prying the inside edges of the bezel, then separate it from LCD back cover and take LCD front bezel away. 3. Disconnect LCD cable from the inverter board and softly lift the board off LCD back cover, then remove the tape pasting the other connector, and disconnect the inverter cable from the inverter board, finally remove the inverter board.
- Page 13 Disassembly procedure 4. Remove the LED at both sides. 5. Remove 6 screws here 2 - 13...
- Page 14 Disassembly procedure 6. Take the LCD panel out of LCD module. 7. Finally, remove 4 screws on the right LCD bracket, and 4 screws on the left side to disassemble LCD brackets 8. Remove the paster and disconnect the VDS cable, then take the VDS cable out of LCD panel. 2 - 14...
- Page 15 Disassembly procedure 9. Remove the right and left hinge. 10. Tear the following pastors on LCD back cover like the picture shows. 2 - 15...
- Page 16 Disassembly procedure 11. Take the camera out of LCD, and then remove camera module. 12. Remove the other paster and take away both LED board out of LCD cover. 2 - 16...
- Page 17 Disassembly procedure 13. Disconnect the camera cable from camera. 14. Remove all tapes on antenna cables. 2 - 17...
- Page 18 Disassembly procedure 15. Remove 2 screws on the white, grey and black antennas respectively, and then remove them from the LCD back cover. 17. Remove 18 screws (M2*5 M2*4) from the bottom case. 2 - 18...
- Page 19 Disassembly procedure 18. Remove 1screw from the top case. 19. Remove 2 screws here, then separate the top case and the bottom case. 2 - 19...
- Page 20 Disassembly procedure 20. Tear of the tapes here, remove 2 screws on the LED board and then remove the LED board. 21. Disconnect the LED cable. 22. Tear of the tapes and disconnect the touchpad cable. 2 - 20...
- Page 21 Disassembly procedure 23. Remove 8 screws on the touchpad bracket and take it away, then remove the touch pad board. 24. Remove 1 piece of tape on Bluetooth cable, disconnect it from the mother board and then remove the blue tooth module. 2 - 21...
- Page 22 Disassembly procedure 25. Disconnect the blue tooth cable. 26. Disconnect the speaker cable and tear of 3 pieces of tape. 27. Remove 4 screws here. 2 - 22...
- Page 23 Disassembly procedure 28. Take away the both speaker. Motherboard M O T H E R B O A R D The illustrations below show how to disassemble and remove the Motherboard. Removing Motherboard M O T H E R B O A R D 1.
- Page 24 Disassembly procedure 2. Disconnect the CPU fan cable and remove 4 screws securing the fan module, then remove the fan module from the mother board. 3. Remove 2 screws and 4 pieces of tape, and then disconnect the cable, take away the modem board.