Advertisement
Quick Links
Advertisement
Related Manuals for Adaptec 5325302040 - Sanbloc S50 Single Jbod 1.2TB 15K Sas
Summary of Contents for Adaptec 5325302040 - Sanbloc S50 Single Jbod 1.2TB 15K Sas
- Page 1 Using the SANbloc S50 JBOD Enclosure Quick Install Guide www.snapserver...
- Page 2 Copyright © 2007, Adaptec, Inc. All rights reserved worldwide. Information in this document is subject to change without notice and does not represent a commitment on the part of Adaptec or any of its subsidiaries. The software described in this document is furnished under a license agreement. The software may be used only in accordance with the terms of the license agreement.
-
Page 3: Kit Contents
12 Serial Attached SCSI (SAS) or 12 Serial ATA (SATA) disk drives. For more information, including supported enclosure configurations, refer to the Adaptec SANbloc S50 SAS JBOD Enclosure User’s Guide on the Kit Contents • SANbloc S50 SAS JBOD enclosure •... - Page 4 Preparing for Installation Carefully read Safety Notices on page 14. Remove all the components from the packaging, inspect them for shipping damage, then place them on an antistatic surface until you are ready to use them. If you are using new disk drives, allow them to acclimate to room temperature before installing them.
- Page 5 Secure the front rails to the front supports of the rack, using the screws or nuts included in the kit. (Use the nuts if your rack does not have threaded holes.) Secure rear rail, using rail length suitable for your rack Rear support Front support...
- Page 6 Slide the enclosure onto the rails, then push it all the way back until the rackmount ears are flush against the front vertical supports and the enclosure rests completely on the rails. Rackmount ears rest against vertical Secure both rackmount ears to the front vertical supports. Secure to the front vertical supports SANbloc S50 SAS JBOD Quick Install Guide...
- Page 7 Installing the Disk Drives Acclimate new disk drives to room temperature before you Caution install them. Before You Begin If you are combining SAS and SATA disk drives in the same SANbloc S50 enclosure, use the figures below to plan where you will be placing the disk drives.
- Page 8 Unsupported Disk Drive Combinations Do not include SAS and SATA disk drives in the same column. Do not place a column of SATA disk drives between two columns of SAS disk drives. Installing the Disk Drives Install the disk drives from left to right across the enclosure. Note On the front of the enclosure, select an open drive slot.
- Page 9 Gently push the lever until it meets the latch on the left side of the drive slot and clicks into place. Repeat for all remaining disk drives. To maintain proper airflow and cooling, a disk drive or a blank Note drive carrier must be installed in every slot of the enclosure.
- Page 10 Connecting the Enclosure Follow the instructions appropriate for your configuration. Connecting to the Host System Use a 4x external SAS cable to connect the HOST port on your SANbloc S50 enclosure to a SAS port on the host system. SANbloc S50 Enclosure Host HOST FAULT !
- Page 11 Use a 4x external SAS cable to connect the EXP port on the first enclosure to the HOST port on a second SANbloc S50 enclosure. SANbloc S50 Enclosures HOST FAULT ! SEP MASTER Host HOST FAULT ! SEP MASTER SAS Cables To expand your configuration with multiple SANbloc S50 enclosures, continue to connect the EXP port of the previous enclosure to the HOST port of the next enclosure.
- Page 12 Powering On Using the included power cords, connect each Advanced Power and Cooling (APC) unit to an AC power source. (Adaptec recommends that you use an uninterruptible power supply to protect your enclosure.) APC Unit Power Port HOST FAULT ! SEP MASTER Power on each APC unit.
- Page 13 Register your enclosure at http://register.adaptec.com. Getting Help For more information, refer to the User’s Guide on the CD. For further assistance, visit http://ask.adaptec.com. Have your TSID number ready. Your TSID number is included on a white, bar-coded label, like the example below: Affix your TSID label here for future reference.
- Page 14 • You must be able to provide proof of purchase showing the date and place of purchase with your Limited Warranty claim; • You must contact Adaptec during the Hardware Warranty Period, and upon request, ship the defective hardware with any additional requested documentation to Adaptec or other address provided by Adaptec at your expense;...
- Page 15 PURPOSE, OR NON-INFRINGEMENT, OR A WARRANTY THAT THE PRODUCT WILL OPERATE ERROR FREE. IN NO EVENT SHALL ADAPTEC, INC. BE LIABLE FOR THE COST OF PROCUREMENT OF SUBSTITUTE HARDWARE, SOFTWARE, OR SERVICES, LOST PROFITS, LOST DATA, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY ARISING IN ANY WAY OUT OF THIS AGREEMENT OR THE SERVER.
-
Page 16: Safety Precautions
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at their own expense. Changes or modifications not expressly approved by Adaptec could void the user’s authority to operate the equipment. Safety Precautions... - Page 17 Do not attempt a remedy if one of the following situations arises; contact Adaptec technical support for assistance: • The power cord or plug is damaged. SANbloc S50 SAS JBOD Quick Install Guide...
- Page 18 • Liquid has penetrated the server. • The server has been exposed to moisture. • The server continues to operate in an unexpected manner even after solutions suggested in the Administration Guide have been followed. Installation Cautions and Notes To prevent personal injury and equipment damage, have Caution someone assist you during installation.
- Page 20 691 Milpitas Blvd. Milpitas, CA 95035 USA 408-957-2550 www.snapserver.com ©2007 Adaptec, Inc. All rights reserved. SnapServer, Adaptec and the SnapServer logo are trademarks of Adaptec, Inc. which may beregistered in some jurisdictions. Part Number: 70990916-001 Rev A...
Need help?
Do you have a question about the 5325302040 - Sanbloc S50 Single Jbod 1.2TB 15K Sas and is the answer not in the manual?
Questions and answers