Advertisement
Quick Links
AP-120-MNT-WJ Access Point Enclosure
Installation Guide
Introduction
The AP-120-MNT-WJ access point (AP) enclosure allows you to install an AP-121 or AP-125 access point
on the wall, directly over an installed junction box. Additionally, this enclosure can be mounted to the
ceiling, using ceiling tile rails.
The AP-120-MNT-WJ kit includes the following pieces:
Plastic base to attach over a standard installed junction box or ceiling tile rail
Plastic enclosure cover
The following plastic connector plate styles:
Blank fillers for unused connectors
1x M4 x 25mm T-20 Torx screw
1x T-20 Torx key
1x white paper label sheet
2x clear window to cover labels
9/16" rail adapter
Top Cover
Clear
Windows
Additional Tools
A screwdriver that matches the screws in the cover plate over the installed junction box
(Optional) flat-head screwdriver or similar tool to punch out antenna access cutouts
0510583-03
| July 2010
1x Keystone connector plate
1x Siemon connector plate
1x Blank plate
2x Keystone
2x Siemon
Base
Keystone
9/16" Rail
Blanking Plates
Adapter
Parts not to scale
T-20 Torx Key
Blank Plate
M4x25mm
Torx Screw
Siemon Connector
Siemon 45*
Blanking Plates
Keystone
Connector
Plate
Plate
1
Advertisement
Related Manuals for Aruba Networks PowerConnect W-AP124
Summary of Contents for Aruba Networks PowerConnect W-AP124
- Page 1 AP-120-MNT-WJ Access Point Enclosure Installation Guide Introduction The AP-120-MNT-WJ access point (AP) enclosure allows you to install an AP-121 or AP-125 access point on the wall, directly over an installed junction box. Additionally, this enclosure can be mounted to the ceiling, using ceiling tile rails.
- Page 2 Installing the AP Enclosure To install the AP enclosure: For ceiling mounted APs, skip step 1 and proceed to step 2 N O T E 1. Attach the base plate as follows: a. Remove the cover plate from an installed junction box (Figure 1).
- Page 3 2. To install the AP enclosure on a ceiling rail: a. Pull the necessary cables through a prepared hole in the ceiling tile near where the AP will be placed. The prepared hole must line up with the cable pass-through in the base plate. b.
- Page 4 c. Align the AP mounting holes over the posts on the base plate. d. Push the AP against the pegs and downward, until the pegs engage the slots at the top of the mounting holes. (Figure Figure 5 Aligning and securing the AP on the base plate AP-120-MNT-WJ Access Point Enclosure | Installation Guide...
- Page 5 5. Attach the connector plate and connectors to the base plate as follows: a. Select the connector plate that matches the existing connectors that were attached to junction box face plate. b. Attach the selected connector plate by sliding it over the opening in the bottom of the base. (See Figure c.
- Page 6 7. Before installing the cover, if the antennas are to be extended, clear the antenna access cutouts (see Figure a. For wall mounted APs, clear the access cutouts marked A. Note that there is a third access cutout located on the base (not illustrated). It is located next to the connector plate b.
- Page 7 8. Install the cover the cover as shown (see Figure a. Attach cover to base. b. Use the M4 x 25mm T-20 Torx screw and the T-20 Torx key to secure the cover to the base. c. (Optional) place paper labels and clear windows over the LED and screw openings. Figure 8 Cover installation AP-120-MNT-WJ Access Point Enclosure | Installation Guide...
- Page 8 The following graphics show the completed installation. Figure 9 Wall mount with antennas extended Figure 10 Ceiling mount with antennas extended © 2010 Aruba Networks, Inc. All rights reserved. July 2010 | 0510583-03...