Specifications; Display Resolutions - Insignia NS-24E200NA14 Important Information Manual

General
Problem Solution
No power
• Make sure that the power cord is correctly connected to
your TV and a power outlet.
• Unplug the power cord, wait 60 seconds, then plug the
cord back in and turn on your TV.
• Other devices (for example, a surround sound receiver,
external speakers, fans, or hair dryers) may be interfering
with your TV. Try turning off one device at a time to
determine which device is causing interference. After you
have determined which device is causing interference,
move it further from the TV to eliminate the interference.
"No signal" error
• Press INPUT and make sure that you have selected the
message is displayed
correct input for the device or service you are trying to use.
• If you are using a cable or satellite box, use the remote that
came with that box to change channels.
• Make sure that you have the correct input selected to view
channels from the cable or satellite box.
After Auto Channel
• Reception can vary by channel depending on the broadcast
Search, there are no
power level of a given station. Contact your cable or
channels
satellite TV provider.
• Make sure that the antenna or cable/satellite TV is
connected securely to your TV.
• Try replacing the cable between the antenna/cable or
cable/satellite box and your TV.
One or more channels
• Make sure that the channels are not blocked. See "Setting
do not display
parental control levels" in the online User Guide.
• Make sure that the channels are not hidden. The channel
may have been deleted from the channel list. You can tune
to the channel by pressing the number buttons or you can
add the channel back to the channel list. See "Hiding
channels" in the online User Guide.
• If you are using a cable or satellite box, use the remote that
came with that box to change channels.
• Make sure that you have the correct input selected to view
channels from the cable or satellite box.
• If you are using an antenna, the digital channel signal may
be low. To check the digital channel signal strength, see
"Checking the digital signal strength" in the online User
Guide.
Password is lost
• Enter 9999 to access parental controls, then set a new
password. See "Setting or changing the password" in the
online User Guide.
Some settings cannot
• If a setting is grayed, the setting is not available in the
be accessed
current video input mode.
Control buttons do
• Make sure that the Button Lock option is set to Off. See
not work
"Locking control buttons" in the online User Guide.
• Unplug the power cord, wait a few seconds, then plug the
cord back in and turn on your TV.
Notes
• If the problem is not solved by using these
troubleshooting instructions, turn off your TV,
then turn it on again.
• Additional troubleshooting information is in
your online User Guide. Go to
www.insigniaproducts.com, then click
Support & Service. Enter your model number
in the box under Manual, Firmware, Drivers
& Product Information, then click

Specifications

Specifications are subject to change without notice.
Dimensions and weight
Without stand
With stand
Screen
Screen size measured
diagonally
Display type
Panel 60 Hz vs.120 Hz
Display resolution
Panel resolution
Aspect ratio
Contrast ratio
(typical)–panel
Dynamic contrast ratio–
list value
TV brightness (minimum)
cd/m2
Comb filter
Response time
Horizontal viewing angle
Vertical viewing angle

Display resolutions

HDMI suggested resolutions
Component video suggested
resolutions
Tuner
Analog
Digital
Inputs
HDMI
Component video
Composite video
Shared audio (component
and composite)
S-Video
PC/VGA
3.5mm PC audio input
DVI
.
USB
Antenna/Cable
www.insigniaproducts.com
NS-24E200NA14
22 × 2 × 13.5 in. (56 × 5.1 × 34.3 cm)
8.14 lbs. (3.7 kg)
22 × 5.5 × 15.1 in. (56 × 14 × 38.4 cm)
8.58 lbs. (3.9 kg)
23.6 in.
LED
60Hz
720p
1366 (H) × 768 (V)
16:9
2000:1
24,000:1
175 nits
3d y/c digital
8 ms
160°
160°
1080p, 1080i, 720p, 480p, 480i
1080i, 720p, 480p, 480i
NTSC
ATSC, 8-VSB, Clear-QAM
1 (side)/1 (back)
E-EDID compliant
HDCP compliant
1 (side)
1 (side)
Shared with component Y
Yes
No
1 (back)
1 (back)
1 (back)
HDMI 1/DVI jack
1 (side)
Supports JPEG and firmware upgrade
1 (back)
5