Table of Contents
Advertisement
181-F GCMON:
Progressive picture improvement.
0=off.
182-F HSPPL:
H sync shift. Default value is 0
183-F VSLPF:
V sync shift. Default value is 0
184-F CVSEL1:
Output select for CVBS2.
185-F CVSEL2:
Output select for CVBS4 or Y.
186-F CLMPSIG1:
Clamping signals ADC1. 0=1
decoder.
187-F YCTOCOMB:
YC to Comb filter. 0=Normal op-
eration.
188-F VDG:
Vertical difference gain. 1=medium2
189-F HDG:
Horizontal difference gain. 2=medium2
190-F DDR:
Diagonal dot reduction.
191-F COR:
Vertical peaking coring. 0=disabled
192-F NOSEL:
Notch filter select. 3=max peaked.
193-F DCR:
Vertical peakigDC rejection filter.
0=disabled.
194-F VPK:
Vertical peaking gain. 0= NO VPK.
195-F LINLENH60:
Number of pixels for 60HZ. De-
fault value is 3.
196-F DISCOMB:
Disable comb filter. Depending
video source selected.
197-F HWID:
Minimum width of H sync. Default
value is 0.
198-F FION:
Increment freeze before V sync. 0= no
freeze.
199-F PPLIP_H:
Default value is 2.
200-F PPLIP_L:
Pixel per line. Default value is 0.
201-F TO1RGB:
YUV output selection. Default value
is 0.
202-F BLANDEL:
Delay in pixels from h sync. De-
fault value is 0 (no delay).
203-F VBLANPOL:
Vertical blanking signal polar-
ity. 0= positive.
204-F HOUTPOL:
Horizontal output polarity. 0=
high active.
3828VD0171G
FACTORY MENU
205-F VOUTPOL:
active.
206-F BLANPOL:
207-F VBLANDEL_95:
in v sync. Default value is 0.
208-F BLANLEN_H:
209-F BLANLEN_L:
st
color
210-F VBLANDEL_40:
start of active blank signal. Default value is 0.
211-F VBLANLEN_H:
start of active blank signal. Default value is 0.
212-F VBLANLEN_L:
start of active blank signal. Default value is 0.
1=medium1
213-F PKLY:
fault value is 237d.
214-F PKLU:
fault value is 254d.
215-F COARSEDEL:
Default value is 5d.
216-F FINEDEL:
fault value is 0.
217-F PKLV:
fault value is 254d.
218-F MDVFON:
219-F FM-RES:
220-F FM-THYON:
221-F FM-THRON:
222-F FMATH:
223-F FMDTH:
TDA4887 NTSC
224-F RGAIN CTRL NTSC:
for white point adjustment. Range: 0-255d.
225-F GGAIN CTRL NTSC:
used for white point adjustment. Range:0-255d.
226-F BGAIN CTRL NTSC:
for white point adjustment. Range: 0-255d.
2-11
Vertical output polarity. 0=high
Blank polarity. 0=high active.
Vertical delay in lines from
Default value is 0.
Default value is 0.
Vertical length in lines from
Vertical length in lines from
Vertical length in lines from
Voltage level for Y DAC output. De-
Voltage level for U DAC output. De-
Luminance coarse delay output.
Luminance fine delay output. De-
Voltage level for V DAC output. De-
Default value is 1.
Default values is 0.
Default value is 0.
Default value is 1.
Default value is 0.
Default value is 15.
Red gain control is used
Green gain control is
Blue gain control is used
DIGITAL FCS - FACTORY MENU
Advertisement
Table of Contents
