Getting Started HP Pavilion dv4 Entertainment PC...
Page 2
Bluetooth is a trademark owned by its common to most models. Some features By installing, copying, downloading, or proprietor and used by Hewlett-Packard may not be available on your computer. otherwise using any software product Company under license. Microsoft and preinstalled on this computer, you agree to Windows are U.S.
Page 3
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
Table of contents 1 Welcome ................................1 Finding information ..........................2 2 Getting to know your computer ........................4 Top ............................... 5 TouchPad ..........................5 Lights ........................... 6 Buttons ..........................7 Keys ............................. 8 Front ..............................9 Right side ............................10 Left side ..............................
Page 6
Using TouchPad gestures ................. 24 Scrolling .................... 25 Pinching/Zooming ................25 Rotating .................... 26 5 Maintenance ..............................27 Inserting or removing the battery ......................27 Replacing or upgrading the hard drive ....................30 Removing the hard drive ....................30 Installing a hard drive ......................31 Adding or replacing memory modules ....................
Welcome ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page ●...
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about ● Quick Setup poster How to set up the computer ● Help to identify computer components ● Getting Started Computer features ● To access this guide: How to connect to a wireless network ●...
Page 9
North America: Hewlett-Packard, MS POD, 11311 Chinden Blvd, Boise, ID 83714, USA ● Europe, Middle East, Africa: Hewlett-Packard, POD, Via G. Di Vittorio, 9, 20063, Cernusco s/Naviglio (MI), Italy ● Asia Pacific: Hewlett-Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507 Please include your product number, warranty period (found on your serial number label), name, and postal address.
TouchPad Component Description ● TouchPad light Off: The TouchPad is on. ● Amber: The TouchPad is off. TouchPad icon Turns the TouchPad on and off. Quickly double-tap the TouchPad icon to turn the TouchPad on and off. TouchPad zone Moves the pointer and selects or activates items on the screen.
Lights Component Description ● Power light White: Power is on. ● Blinking white: The computer is in the Sleep state. ● Off: The computer is off or in Hibernation. ● Mute light Amber: Computer sound is off. ● Off: Computer sound is on. ●...
Buttons Component Description ● Power button When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button briefly to initiate Sleep. ● When the computer is in the Sleep state, press the button briefly to exit Sleep.
Keys Component Description Displays system information when pressed in combination with the key. Displays system information when pressed in combination with the esc key. Windows logo key Displays the Windows Start menu. Windows applications key Displays a shortcut menu for items beneath the pointer. Action keys Execute frequently used system functions.
Right side Component Description Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. ● Drive light Blinking white: The hard drive is being accessed.
Page 17
Component Description ● Battery light White: The computer is connected to external power and the battery is fully charged. ● Blinking white: The computer is in the Sleep state. ● Amber: A battery is charging. ● Blinking amber: The battery has reached a low battery level, or there is a battery error.
Left side Component Description Optical drive Reads and writes (select models only) to an optical disc. ● Optical drive light On: The optical drive is being accessed. ● Off: The optical drive is idle. Optical drive eject button Opens the optical drive to insert or remove optical media. USB port Connects an optional USB device.
Display Component Description WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). Internal microphones (2) Record sound. Webcam light On: The webcam is in use. Webcam Records video and captures still photographs. To use the webcam, select Start > All Programs > CyberLink YouCam *The antennas are not visible from the outside of the computer.
Rear Component Description Display hinges Allow the display to open and close. Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Chapter 2 Getting to know your computer...
Bottom Component Description Vents (4) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Memory module compartment Holds the memory module.
Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: ●...
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service.
Connecting to an existing WLAN Turn on the computer. Be sure that the WLAN device is on. Click the network icon in the notification area, at the far right of the taskbar. Select a network to connect to. Click Connect. If required, enter the security key.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network, select Start >...
Keyboard and pointing devices ● Using the keyboard ● Using pointing devices Using the keyboard Using the action keys Action keys are customized actions that are assigned to specific keys at the top of the keyboard. The icons on the through keys represent the action key functions.
Page 27
Icon Description Opens Help and Support, which provides information about your Windows operating system and computer, answers to questions and tutorials, and updates to your computer. Help and Support also provides automated troubleshooting and links to support specialists. Decreases the screen brightness level incrementally when you hold down this key. Increases the screen brightness level incrementally when you hold down this key.
Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer. Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad icon. NOTE: The TouchPad light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go. Using pointing devices...
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock.
Maintenance ● Inserting or removing the battery ● Replacing or upgrading the hard drive ● Adding or replacing memory modules ● Updating programs and drivers ● Routine care Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: Inserting or removing the battery...
Page 34
Insert the battery into the battery bay until it is seated. ▲ The battery release latch automatically locks the battery into place. To remove the battery: CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information.
Page 35
Pivot the battery (2) upward and lift it out of the computer (3). Inserting or removing the battery...
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button.
Lift the hard drive (2) out of the hard drive bay and disconnect the hard drive cable (3). Installing a hard drive Connect the hard drive cable to the hard drive (1). Replacing or upgrading the hard drive...
Page 38
Insert the hard drive into the hard drive bay (2) and replace and tighten the 2 hard drive screws (3). Align the tabs (1) on the hard drive cover with the notches on the computer. Close the cover (2). Chapter 5 Maintenance...
Tighten the hard drive cover screws (3). Replace the battery. Reconnect external power and external devices. Turn on the computer. Adding or replacing memory modules The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
Page 40
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button.
Page 41
Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container.
Page 42
Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place. CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module.
Page 43
Tighten the 2 memory module compartment cover screws (3). Replace the battery. Reconnect external power and external devices. Turn on the computer. Adding or replacing memory modules...
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available. Routine care Cleaning the display CAUTION:...
Backup and recovery ● Restore ● Creating restore media ● Performing a system restore ● Backing up and recovering your information Your computer includes tools provided by the operating system and HP to help you safeguard your information and restore it if ever needed. This chapter provides information on the following topics: ●...
Restore In the event of hard drive failure, to restore your system to its factory image you will need a set of recovery discs or a recovery flash drive that you can create using HP Recovery Manager. HP recommends that you use this software to create either a set of recovery discs or a recovery flash drive immediately after software setup.
To create a set of recovery discs or a recovery flash drive: Select Start > All Programs > Recovery Manager > Recovery Media Creation. Follow the on-screen instructions. Performing a system restore Recovery Manager software allows you to repair or restore the computer to its original factory state. Recovery Manager works from recovery discs, a recovery flash drive, or from a dedicated recovery partition (select models only) on the hard drive.
Restoring using the restore media If possible, back up all personal files. Insert the first recovery disc into the optical drive on your computer or an optional external optical drive, and then restart the computer. – or – Insert the recovery flash drive into a USB port on your computer, and then restart the computer. NOTE: If the computer does not automatically restart in the Recovery Manager, the computer boot order needs to be changed.
Changing the computer boot order To change the boot order for recovery discs: Restart the computer. Press while the computer is restarting, and then press for boot options. Select Internal CD/DVD ROM Drive from the boot options window. To change the boot order for recovery flash drive: Insert the flash drive into a USB port.
To create a screen shot: Display the screen you want to save. Copy the screen image: To copy only the active window, press alt+fn+prt To copy the entire screen, press fn+prt Open a word-processing document, and then select Edit > Paste. The screen image is added to the document.
Using Windows system restore points A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes. NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point.
Customer support ● Contacting customer support ● Labels Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to...
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component Product name Serial number (s/n) Part number/Product number (p/n) Warranty period Model description Have this information available when you contact technical support.
Specifications ● Input power ● Operating environment Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz.
Operating environment Factor Metric U.S. Temperature Operating (writing to optical disc) 5°C to 35°C 41°F to 95°F Nonoperating -20°C to 60°C -4°F to 140°F Relative humidity (noncondensing) Operating 10% to 90% 10% to 90% Nonoperating 5% to 95% 5% to 95% Maximum altitude (unpressurized) Operating -15 m to 3,048 m...
Index front 9 network 10 action keys left side 12 RJ-45 (network) 10 decrease screen brightness rear 14 right side 10 keys Help and Support 21 top 5 action 8 identifying 8 connector, power 11 esc 8 increase screen brightness 21 fn 8 next track 21 digital media slot, identifying 10...
Page 57
memory module compartment, regulatory information Windows applications key, identifying 15 regulatory label 47 identifying 8 Microsoft Certificate of Authenticity wireless certification labels 47 Windows logo key, identifying 8 label 47 restore points 45 wireless certification label 47 mouse, external RJ-45 (network) jack, identifying wireless light 6 setting preferences 22 wireless network (WLAN),...