General Cleaning; Your Appliance; To Remove And Replace Oven Door - Frigidaire 318200912 Owner's Manual

Electric wall oven
Table of Contents


General Cleaning

Cleaning Various Parts of Your Appliance
Before cleaning any part of the appliance, be sure all controls are turned OFF and the appliance is COOL. REMOVE SPILLOVERS AND HEAVY
Aluminum (Trim Pieces)
Glass, Painted and Plastic Body
Parts and Decorative Trim
Control Panel
(Models with Control Knobs)
Control Panel
(Models with tactile touch-
Porcelain Enamel
Broiler Pan and Grid, Door Liner
Stainless Steel, Chrome
Decorative Trim
Oven Racks
Oven Door

To Remove and Replace Oven Door

Open the door to the fully opened
Pull up the lock located on each hinge
support and engage it in the hook of
the hinge lever. You may have to apply
a little downward pressure on the
door to pull the locks fully over the
Grasp the door by the sides, pull the
bottom of the door up and toward
you to disengage the hinge supports.
Keep pulling the bottom of the door
toward you while rotating the top of
the door toward the appliance to com-
pletely disengage the hinge levers.
Proceed in reverse to re-install the door. Make sure the hinge supports are fully engaged before unlocking the hinge levers.
How to Clean
Use hot, soapy water and a cloth. Dry with a clean cloth.
For general cleaning, use hot, soapy water and a cloth. For more difficult soils and built-up grease,
apply a liquid detergent directly onto the soil. Leave on soil for 30 to 60 minutes. Rinse with a damp
cloth and dry. DO NOT use abrasive cleaners on any of these materials; they can scratch.
Before cleaning the control panel, turn all controls to OFF and remove the control knobs. To remove,
pull each knob straight off the shaft. Clean using hot, soapy water and a cloth. Be sure to squeeze
excess water from the cloth before wiping the panel; especially when wiping around the controls.
Excess water in or around the controls may cause damage to the appliance. To replace knobs after
cleaning, line up the flat sides of both the knob and the shaft; then push the knob into place.
Before cleaning the control panel, turn all controls to OFF. Lightly spray the control panel with a
liquid cleaner. Wipe with a soft cloth or paper towel. DO NOT use abrasive cleaners or scouring pads.
These can permanetly damage the control panel surface.
Gentle scouring with a soapy scouring pad will remove most spots. Rinse with a 1:1 solution of
clear water and ammonia. If necessary, cover difficult spots with an ammonia-soaked paper towel
for 30 to 40 minutes. Rinse with clean water and a damp cloth, and then scrub with a soap-filled
scouring pad. Rinse and wipe dry with a clean cloth. Remove all cleaners or the porcelain may
become damaged during future heating.
Clean with hot, soapy water and a dishcloth. Rinse with clean water and a cloth. Cover stubborn
spots with an ammonia-soaked paper towel for 30 to 40 minutes. Rinse. Cleaners made especially
for stainless steel are recommended. Be sure to rinse the cleaners as bluish stains may occur during
heating and cannot be removed.
Remove racks. See "Removing and Replacing Oven Racks" under Before Setting Oven Controls.
Use a mild, abrasive cleaner, following manufacturer's instructions. Rinse with clean water and dry.
After cleaning the racks, rub the sides of the racks with wax paper or a cloth containing a small
amount of baby oil or salad oil (this will make the racks glide more easily into the rack positions).
The door may be removed to facilitate cleaning. To remove oven door, see instructions. To clean
oven door, wash with hot, soapy water and a clean cloth. DO NOT immerse the door in water or
clean the oven door gasket. The oven door gasket is essential for a good seal. Care should be taken
not to rub, damage or remove the gasket.
(down swing door models) (some models)
Door Removal

Hide quick links:


Table of Contents

Subscribe to Our Youtube Channel

This manual is also suitable for:


Table of Contents

Save PDF