Completing The Set Up; Connecting The Water Supply Line To The Refrigerator - Samsung RF24FSEDBSR User Manual

3. Connect the water line installation kit to the
shut off valve.
Cold water line
Pipe clamp
Shut off valve
Connecting the water supply line to
the refrigerator.
There are several items that you need to purchase
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
Use Copper Tubing Use Plastic Tubing
• ¼" copper tubing • ¼" plastic tubing
• ¼" compression nut
(1pc) • ¼" compression nut
• Ferrule (2pc)
Refrigerator
Compression
Nut (1/4")
(Assembled)
Ferrule
(Not supplied)
Copper tubing
or
(Not supplied)
Household water supply line
1. Connect the household water line to the
assembled compression fitting.
- If you are using copper tubing, slip the
compression nut ( B ) (not supplied) and
ferrule (not supplied) on the copper tubing (not
supplied) as shown.
- If you are using plastic tubing ( B ) , insert the
molded end (Bulb) of the plastic tubing ( B )
into the compression fitting.
Do not use without the molded end (Bulb)
CAUTION
2. Tighten the compression nut ( B ) onto the
3. Turn the water on and check for any leakage.
Water line installation kit
4. Flush 1 gallon of water through the filter
5. After you turn on the refrigerator, let the ice
If you have to repair or disassemble the water line,
→ Molded end(Bulb)
cut off 1/4" of the plastic tubing to make sure you
get a snug, leak-free connection.
(1pc)

COMPLETING THE SET UP

Now that you have your new refrigerator installed
Plastic Tubing
in place, you are ready to set up and enjoy the
(Assembled)
features and functions of the appliance.
Compression
By completing the following steps, your refrigerator
Fitting
should be fully operational.
(Assembled)
Molded 1. Make sure your refrigerator is in an appropriate
end(Bulb)
Compression
nut (B) (1/4")
(Not supplied)
2. Once the refrigerator is plugged in, make sure the
Plastic tubing (B)
(Not supplied) 3. Set the Temperature control to the coldest
4. After you plug the refrigerator in, it will take a few
of the plastic tubing ( B ).
compression fitting.
Do not over-tighten the compression nut ( B ) .
If you find water drops or leakage in the
connection areas, turn off the main water
supply. Check the connections and, if
necessary, tighten.
before drinking or using the water from the
refrigerator. (Flush approximately 6 minutes.)
To flush, press a large glass or cup against the
water dispenser lever. Fill the glass, empty it
into the kitchen sink after it is filled, and then
repeat.
maker make ice for 1 to 2 days. Over that
period of time, throw out the first 1 or 2
buckets of ice the freezer makes to ensure all
impurities have been removed from the water
line.
Only connect the water line to a drinkable
water source.
You can test the water line quickly using a
paper cup. Under normal conditions, the
water dispenser can fill a 5.75 oz. (170cc)
cup in about 10 seconds.
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
interior light comes on when you open the doors.
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
hours to reach the appropriate temperature. You
can store food and drinks in the refrigerator after
the temperature is sufficiently cool.
If condensation or water drops appears on
both sides of fridge door's central part, turn
the Energy Saver mode off after removing the
condensation. (See the explanation on Energy
Saver button in the USING THE CONTROL
PANEL.)
setting up _15