Related Manuals for Soho Connect FSD-800
Summary of Contents for Soho Connect FSD-800
- Page 1 SOHOConnect Series FSD-800 8-port 10/100Mbps Ethernet Switch FSD-8080 User's Manual...
-
Page 2: Fcc Warning
Revision The information in this manual is subject to change without notice. User's manual for PLANET SOHOConnect Series Switch Model: FSD-800 Rev: 1.0 (July. 2000) Part No. EM-FSD800 SOHOConnect Series... -
Page 3: Table Of Contents
CHAPTER 1 ................1 ............1 ENERAL NTRODUCTION Checklist................1 Introduction...............1 Features ................3 CHAPTER 2 ................5 ............5 ARDWARE ESCRIPTION Front Panel ...............5 Rear Panel ................6 Hardware Installation ............7 Configuration..............8 Switch Operation.............10 CHAPTER 3 ................15 .............15 ROUBLESHOOTING APPENDIX A ................17 : ..............17 PECIFICATIONS FSD-800 User's Manual... - Page 4 This page is intentionally left blank SOHOConnect Series...
-
Page 5: Chapter 1
Introduction The FSD-800, 8-port 10/100Mbsp Ethernet Switch is designed to allow simultaneous transmission of multiple packets via an internal high-speed data channel. This means that it can partition... - Page 6 In the following sections, the term “Switch” will represent Planet’s FSD-800, and “switch” for third part Ethernet switches. This Switch is a highly reliable network switch and is the ideal device for bridging Ethernet to Fast Ethernet workgroups or networks.
-
Page 7: Features
Full/Half-Duplex capability on every TX ports, total bandwidth is up to 200Mbps/port Support up to 4K Uni-cast address, Layer 2 address resolution-Self Learning Broadcast storm control IEEE802.3x compliant full-duplex flow control Half-duplex flow control 100~240VAC Full range internal power supply FSD-800 User's Manual... - Page 8 LED indicators for simple diagnostics and management Port#8 provides an extra port for MDI and MDI-X mode PC or hub Uplink. Plug and Play SOHOConnect Series...
-
Page 9: Chapter 2
LED indicators. Before connecting any network device to the hub, read this chapter carefully. Front Panel The unit front panel provides a simple interface monitoring the Switch. It includes a power indicator for each port. Figure 1. Front Panel of FSD-800... -
Page 10: Rear Panel
Ethernet segment of this port. Whenever a collision is detected, the respective COL indicator will briefly blink Rear Panel The rear panel of the Switch indicates an AC-jack power socket, which accepts 100~240VAC Power inlet for FSD-800. SOHOConnect Series... -
Page 11: Hardware Installation
100V~240VAC 50~60Hz Figure 2. Rear Panel of FSD-800 Hardware Installation 1. Place the Switch on a smooth surface 2. Connect the output cord of power supply to the AC-jack. 3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP cabling. -
Page 12: Configuration
may initially seem to work, it will soon cause data loss. All kinds of hub/PC can connect to switch by using straight- through wires. The hub provides one additional RJ45 connector that is converted from port 1, labeled “Uplink” port. Either port 8 or Uplink port can be used at one time. - Page 13 Plug one end of the Category 3 UTP Cable into one port of the Switch, and the other end of this cable into “Uplink” port of the 10Mbps Ethernet Hub. The cable length between these 2 connecting points should not exceed 100 meters. FSD-800 User's Manual...
-
Page 14: Switch Operation
Switch Operation Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. The information comes from the learning process of Ethernet Switch. - Page 15 However, the switch is most commonly used to segment existing hubs, which nearly always improves overall performance. An Ethernet Switch can be easily configured in any Ethernet network environment to significantly boost bandwidth using conventional FSD-800 User's Manual...
- Page 16 cabling and adapters. Due to the learning function of the Ethernet switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address is on the same segment as the source address.
- Page 17 If attached device is: 100Base-TX port will set to: 10Mbps, no auto-negotiation 10Mbps 10Mbps, with auto-negotiation 10/20Mbps (10Base-T/Full-Duplex) 100Mbps, no auto-negotiation 100Mbps 100Mbps, with auto-negotiation 100/200Mbps (100Base-TX/Full-Duplex) FSD-800 User's Manual...
- Page 18 This page is intentionally left blank SOHOConnect Series...
-
Page 19: Chapter 3
Chapter 3 Troubleshooting This chapter contains information to help you solve problems. If the Switch is not functioning properly, make sure the Switch was set up according to instructions in this manual. The Link LED is not Lit Solution: Make sure the switch configuration is consistent with the connecting device Check the cable connections. - Page 20 The address table may contain older information than of the address table of that node. Please power down to refresh the address information. SOHOConnect Series...
-
Page 21: Appendix A
Appendix A Specifications: General (Ethernet) Standards: IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100 Base-TX Fast Ethernet ANSI/IEEE Std 802.3 N-way auto-negotiation IEEE 802.3 Frame types: Transparent IEEE 802.3 MAC layer frame size: 64 - 1518 Bytes Protocol: CSMA/CD Data Transfer Rate: Ethernet: Fast Ethernet: 10Mbps (half duplex) - Page 22 General (Ethernet) Humidity 10% ~ 90% non-condensing Dimensions 251 x 118 x 37 mm FCC Class A, CE Mark Class A Performance Transmission Store-and-forward Method Filtering Address 4 K entries / device Table Packet 148,800pps per port (for 100Mbps) Filtering/Forwarding Rate 14,880pps per port (for 10Mbps) MAC Address...