1. Notes on safety For your own safety you should read through this chapter at first completely! Risk of electrical shocks! • Only connect the device using the mains adaptor supplied to a properly wired and earthed mains power socket providing mains voltage of 230 V ~ /50 Hz. •...
Page 4
X 8 faders for manual control X All data can be sent or received between two units X Auto programs (scenes and chases) under control by Wait Time sliders (or Tap Sync) and Fade Time sliders X Fade Time/Assign Fade Time X The scanners under control by Pan and Tilt jog wheels (Master II) X Fine adjustment of the Pan and Tilt X Reverse DMX channels causing the faders to control the output reversely...
3. Overview Controller Front 1) Scanner Buttons (1-12): 12 scanners of 16 DMX channels & fader control Scanners DMX channels Fader control 1-16 17-32 33-48 49-64 65-80 81-96 97-112 113-128 129-144 145-160 161-176 177-192 Scanners DMX channels Fader control 1-16 17-32 33-48...
Page 6
Scanners DMX channels Fader control 49-64 65-80 81-96 97-112 113-128 129-144 145-160 161-176 177-192 Press a scanner button to turn on manual fader control. Press the scanner button again to turn off fader control. The LED next to the button lights up or goes out to indicate your selection. 2.
Rear View 1. AUDIO IN 0.1V~1Vp-p. 2. MIDI IN Receives MIDI data. 3. DMX Polarity Select Used to select DMX polarity. 4. DMX Out This connector sends your DMX value to the DMX scanner or DMX pack. 5. DMX In This connector accepts your DMX input signals.
Page 8
DATA 151 DMX value (000-255) WT: 1M36S The current Wait Time is 1 minute and 36 seconds TP: 5.32S The time of the last two taps is 5.32 seconds FT: 10.5S Fade Time is 10.5 seconds ASS 07 08 Assign DMX channels 7 and 8 RES 10 13 Reverse DMX Channels 10 and 13 SN 6...
Page 9
8. Repeat steps 3-7 until all desired scenes have been programmed into memory. Tap the Scanner button again to turn off its fader control. To set another scanner (scanner), you may tap the corresponding Scanner button to turn on its fader control, then you may begin your programming again.
Page 10
4. Use the Faders or jog wheels to make your desired adjustments. 5. Once you’ve made your changes, tap the MIDI/Rec button 6. Tap the Scene button that corresponds to the scene you’re editing. This will overwrite the exited scene NOTE: Be sure to select the same scene in steps 3 and 6, otherwise you may accidentally record over an exited scene.
Page 11
4-2.3 Scene Copy 1. Program enable. 2. Tap the Bank Up/Down button to select the bank that contains the scene you wish to copy. 3. Select the scene you want to copy by tapping its Scene button 4. Tap the Bank Up/Down button to select the bank you wish to copy the scene to.
Page 12
4-2.4 Delete a Scene 1. Tap the desired Scene button to select the scene you wish to delete 2. Press and hold down the Auto/Del button. While holding down the Auto/Del button, tap the Scene button that stores the scene you wish to delete. 4-2.5 Delete all Scenes This function will reset all DMX channel to 0 output.
5. Tap the Music/Bank Copy button, all LEDs will flash three times briefly indicating the function has been completed. 6. Press the Program button for three seconds to exit Programming mode. 4-3 Programming Chase You must program scenes before you can program chases, this function allows you to store up to 240 scenes into one chase.
Page 14
4-3.2 Add a Step 1. Program enable. 2. Select the chase you wish to add a step to. 3. Tap the Tap/Display button, the LCD shows the current step. 4. Tap the Bank Up/Down button to scroll to the step you wish to add a step after.
Page 15
4-3.3 Delete a Step 1. Program enable. 2. Select the chase that contains the step you wish to delete. 3. Tap the Tap/Display button, the LCD shows the current step. 4. Tap the Bank Up/Down button to scroll to the step you wish to delete. 5.
4-4 Assign/Reverse DMX channel 4-4.1 Assign DMX channel 1. Program enable. 2. Press the Fine and Mode buttons at a time,the Assign LED lights up indicating Assign mode is active. 3. Use Bank Up/Down button to change between the Pan and Tilt, the corresponding LED lights indicating this selection.
Page 17
7. While pressing the Mode button, tap the Scene button, all LEDs should flash briefly indicating the DMX channel is assigned.( Scene button 1 stands for DMX channel 1, Scene button 2 stands for DMX channel 2, and so on.) 8.
Page 18
6. Tap the Page Select button to select Page A or Page B. 7. While pressing the Mode button, tap the Scene button, all LEDs should flash briefly indicating the DMX channel is reversed.( Scene button 1 stands for DMX channel 1, Scene button 2 stands for DMX channel 2, and so on.) 8.
Page 19
4-4.4 Delete a scanner of DMX channels 1. Activate Assign or Reverse mode (Described in the sub-chapter 2.2.4.1 or 2.2.4.2). 2. Tap the Scanner button to select the scanner you wish to delete. 3. Press the Mode and Auto/Del buttons at a time,all LEDs should flash briefly, indicating the scanner is deleted.
Page 20
3. Tap the Scanner button that holds the Pan and Tilt channel, the LCD shows the Pan and Tilt. 4-4.7 Set Up a new Logo 1. Turn the power off. 2. Press and hold down the Scanner 6 and Scanner 12 buttons at a time. Apply the power again while pressing the two buttons, then release the two buttons.
Page 21
4-4.8 Auto Address 1. Hold on the Black out /Stand alone button for 3 seconds to enter Stand- Alone mode. 2. Hold down the Scanner 1 button and then press Black out /Stand alone button. You will see the pan & tilt of all the fixtures in the chain stopping at the central position.
4-5 Running Scenes 4-5.1 Manual Mode 1. When the power is turned on, this unit enters Manual mode automatically. This function allows you to run a bank of programmed scenes in a sequential loop. 2. Make sure Auto and Music LEDs are both off. 3.
4. Tap the Auto/Del button again to exit Auto mode. 4-5.3 Music Mode 1. Tap the Music/Bank Copy button to activate Music mode. The Music LED lights indicating Music mode is active. 2. Use the Bank Up/Down button to select the bank that holds the scenes you wish to run.
Page 24
4-6.2 Auto Mode 1. Tap the Auto/Del button to activate Auto mode. The Auto LED lights indicating Auto mode is active. 2. Select your desired chase by tapping one of the six Chase buttons. A second tap of this button will deactivate this function. 3.
4-7 MIDI Operation 4-7.1 MIDI Channel Setting 1. Press and hold down the MIDI/Rec button for three seconds, the LCD show the MIDI channel of last time. 2. Use the Bank Up/Down button to select the DMX channel 01-16 to assign to MIDI channel.
4-8 Send File Dump NOTE You must set up proper connection before you can send or receive the file dump. 1. With the power off, press and hold down the Scanner buttons 2, 3 and Scene button 1 at a time. 2.
5. Disposal Never throw the device into the regular household waste at the end of its useful life. This product is subject to the European Directive 2002/96/EC. • Dispose of the device through an approved disposal centre or at your community waste facility. •...
Need help?
Do you have a question about the DMX MASTER I & II and is the answer not in the manual?
Questions and answers