1. Manuals
  2. Brands
  3. ATCOM Manuals
  4. VoIP
  5. MP01
  6. Quick start manual

ATCOM MP01 Quick Start Manual

Hide thumbs Also See for MP01:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Administrator's Manual, Setup Manual

MP01 Quick Start Guide

Version: V2.0
2011-10-12

Advertisement

Table of Contents
loading

Related Manuals for ATCOM MP01

Summary of Contents for ATCOM MP01

  • Page 1: Mp01 Quick Start Guide

    MP01 Quick Start Guide Version: V2.0 2011-10-12...

  • Page 2: Table Of Contents

    Table of Contents MP01 QUICK START GUIDE ....................2 USE MP01 TO SET UP A WIFI TELEPHONY NETWORK AND MAKE INTERNAL PHONE CALLS ...................... 2 MP01 GUI ............3 OGIN TO THE CONFIGURATION ONFIGURE THE WIRELESS ADDRESS ..............3 MP01 AKE PHONE CALLS BETWEEN .................

  • Page 3: Mp01 Quick Start Guide

    MP01 Quick Start Guide Instructions: The MP01 is a WiFi ATA running in mesh protocol. You can use MP01s to set up a simple telephony network quickly. This Quick Start Guide describes how to set up a WiFi telephony network with MP01s. After this Quick Start Guide, you should be able to use MP01s to set up the telephony network in 1 hour.

  • Page 4: Step 1-Login To The Mp01 Configuration Gui

    2/ Every MP01 can be a reply for other MP01. It means even MP01 B can’t reach MP01 C directly, it can be still possible to reach MP01 C via MP01 A. Note: The PC is only use for configuring, you don’t need it after the network is set up.

  • Page 5: Basic Lan/Wifi Settings For Mp01

    B, just dial 20 on the phone. Because mesh node B has wireless IP address 10.130.1.20/24. After finishing these two steps, the MP01 will be added into the mesh network automatically. Configure the other MP01 to set up your own mesh network.

  • Page 6: Configure The Basic Wifi Settings

    (for client mode) or hostapd (for AP and ad-hoc mode) to be installed. Note: All MP01 in the same mesh network should use the same channel. By default, you don’t need to change channel. Except the channel is congest with other WiFi network.

  • Page 7: Change Administrator Password

    3. Change administrator password On OpenWrt web page, under System->Admin Password, you will enter the related page for you to change the password. Click button to change the password.

  • Page 8: Upgrade Firmware

    Installing with the LUCI Web interface. The .img file will be used to install via the web interface. Download the MP device firmware from ATCOM website: http://www.atcom.cn/download.html. If you are using a new MP it will operate with IP addresses of 10.130.1.20 (LAN) and 172.31.255.254 (Fallback).

  • Page 9: Installing With The Potato-Flash Utility

    When the file has been uploaded, the Checksum and Size details will be displayed. Click on the Proceed button and the flashing process will begin. This may take several minutes and then the MP device will restart. After the MP device has restarted and the WiFi led has started to flash, allow three minutes for the flashing process to complete.
  • Page 10 +x /home/potato_flash.exe 2. Download the firmware Download device firmware from ATCOM website: http://www.atcom.cn/download.html. Download the .squashfs .lzma files and save to /home/ directory. 3. Set up networking on your PC This step will ensure that potato-flash has proper access to the PC Ethernet network port.
  • Page 11 FOR MORE THAN A MINUTE, START AGAIN... A flash size of 8 MB was detected. rootfs(0x006a0000) + kernel(0x00100000) + nvram(0x00000000) sums up to 0x007a0000 bytes Setting IP address... Initializing partitions... Now uploading kernel... Sending kernel, 1408 blocks... Flashing kernel... Loading rootfs... Sending rootfs, 7424 blocks...

Table of Contents