Planet FT-807 User Manual

Fast ethernet converter
Hide thumbs Also See for FT-807:

Advertisement

Quick Links

Trademarks
Copyright
PLANET Technology Corp. 2005.
Contents subject to which revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with
respect to the quality, performance, merchantability, or fitness for
a particular purpose.
PLANET has made every effort to ensure that this User's Manual
is accurate; PLANET disclaims liability for any inaccuracies or
omissions that may have occurred.
Information in this User's Manual is subject to change without
notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies
that may be contained in this User's Manual. PLANET makes no
commitment to update or keep current the information in this
User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading,
or incomplete, we would appreciate your comments and
suggestions.

FCC Warning

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at whose
own expense.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FT-807 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Planet FT-807

  • Page 1: Fcc Warning

    PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for...
  • Page 2 Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET Fast Ethernet Converter User’s Manual FOR MODEL: FT-807 Rev: 1.1(December, 2005) Part No. 2010-AA3331-000...
  • Page 3: Table Of Contents

    Table of Contents Chapter 1 Introduction 1.1 Product Description 1.2 Packet Contents 1.3 Technical Specification 1.4 Product Outlook 1.5 Duplex Mode Setting 1.6 Power information Chapter 2 Installation APPENDIX A: RJ-45 pin assignment and cable system 5 A. 1 10/100Mbps, 10/100Base-TX A.
  • Page 4 This page is intentionally left blank...
  • Page 5: Chapter 1 Introduction

    Chapter 1 Introduction The PLANET FT-807 is a 10/100Base-TX shielded twisted pair (STP) to Fast Ethernet 100Base-FX fiber converter. It supports full-duplex operations at its fiber-optic interface in the form factor of SMI (Small Multimedia Interface) interface. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port.
  • Page 6: Product Outlook

    Fiber Con- SMI POF port (multi-mode), 650nm nector wavelength 10/100Mbps (TP) ; Auto-Negotiation for Data Rate duplex mode 100Mbps (FX) ; full-duplex mode TP Cable 4 pair Cat. 3 or 5 UTP, up to 100m IEEE 1394b SMI Patch cord (0.98mm Fiber Cable /1mm), up to 50m LED indicators...
  • Page 7: Duplex Mode Setting

     full-duplex, where a dual-speed hub will detects NOTE: half. The fiber port (POF) port of FT-807 is fixed at 100Mbps full-duplex mode. The link partner should also set at 100Mbps full-duplex mode at the same time. 1.6 Power information The power jack of FT-807 is with 2.5mm in the central post...
  • Page 8  Attach a Cat. 5 UTP cable from the 10/100Base-TX net- work to the RJ-45 port on the FT-807.  Connect the 5VDC power adapter to the FT-807 and verify that the Power LED lights up.  Turn on the power of the device/station, the TP and POF LED should light when all cables are attached.
  • Page 9: Pin Assignment And Cable System

    APPENDEX A Appendix A: RJ-45 pin assignment and cable system A.1 10/100Mbps, 10/100Base-TX When connecting your 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/MDI-X detection.
  • Page 10: 100Mbps, 100Base-Fx, Smi Type Connector

    A.2 100Mbps, 100Base-FX, SMI type connector FT-807 is using POF SMI type connector that is mostly being used for IEEE1394 transmission. The followings show the basic information.
  • Page 11 This page is intentionally left blank...
  • Page 12 This page is intentionally left blank...

Table of Contents