DLS MR5 Owner's Manual

DLS MARINE RANGE SPEAKERS
D L S M A R I N E R A N G E S P E A K E R S
Thank you for buying a DLS MARINE speaker.
This manual will show you how to do a correct instal-
lation. Please read the entire manual before you begin
the installation.

Features and benefits:

- Excellent audio performance, transparent
and clear sound
- Water protected design
- Easy installation
Installation
Install the speakers in a solid and stable panel to get the best
sound quality. Use the template to cut and drill. Fasten with
stainless steel screws. Make sure to connect with the same pola-
rity on both speakers.
NOTE! Avoid an installation close to the magnetic compass, the
speaker magnets can influence the compass needle.
The MR5 and MR6 are designed for use both outdoors and
indoors on a vessel or yacht. These speakers are well protected
against water, but not fully waterproof.
The MR426 have a water resistant front but not so well protected
on the back. Avoid installing them where they are likely to get
wet on the back side. The magnet system is magnetic shielded.
Break-in period
Allow the speakers to play at normal volume for at least 15-20
hours. After this time the performance is correct.
Technical Assistance
For technical assistance ask the shop where the product was sold
or the distributor in your country. You can also send an e-mail to
info@dls.se
Information can also be found on our web-site www.dls.se
We follow a policy of continuous advancement in development.
For this reason all or part of specifications & designs may be
changed without prior notice.
Warranty service
This speaker is covered by warranty, depending on the condi-
tions in the country where it is sold. If the speaker is returned for
service, please include the original dated receipt (or a copy) with
the product.
WARNING
While these speakers are specially designed for marine applica-
tions, they are not fully waterproof which must be taken in consi-
deration when doing the installation.
More facts:
Model MR5
Size 5,25" / 13 cm
Nom. power (RMS) 60 W
Maximum power 100 W
Frequency range 65 Hz - 20 kHz
Magnet diameter 70 mm / 2,75"
Outer diameter 150 mm / 5,9"
Mounting depth 54 mm / 2,12"
Mounting hole 120 mm / 4,72"
Tweeter 16 mm /0,63"
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 84 00 60
Fax: +46 31 84 40 21
E-mail: info@dls.se
www.dls.se
DLS Svenska AB 2009-02-17

OWNERS MANUAL

MR6 MR426
6,5" / 16,5 cm 6,5" / 16,5 cm
60 W 60 W
100 W 100 W
55 Hz - 20 kHz 50 Hz - 20 kHz
80 mm / 3,15" 80 mm / 3,15"
180 mm / 7,08" 165 mm / 6,5"
63 mm / 2,48" 73 mm / 2,87"
140 mm / 5,5" 145 mm / 5,7"
16 mm / 0,63" 20 mm / 0,8"
Safety Considerations:
Your speakers must be installed in a manner which does
not interfere with your vessel's factory installed electronic
devices. You should also take the time to securely mount
them so that they do not come loose in the event of a col-
lision or a sudden jolt to the vessel.
- Check before drilling any holes in your vessel to make
sure that you will not be drilling through the hull, a fuel tank,
fuel line, wiring harness or other vital vessel system.
- Protect all wiring from sharp edges (metal, fibreglass,
etc.) by carefully routing them, tying them down and using
grommets and loom where appropriate.
Connection of MR5, MR6
Input from +
stereo / amplifier
_
Filter installation and connection of MR426
_
+
Input from stereo / amplifier
Speaker connection and tweeter level select:
Use the red, blue and black cables to connect between the filter box
and speaker terminal. Note the speaker terminal colour marking.
Tweeter level select:
Select tweeter level by moving the jumper inside the filter box bet-
ween HI / LO. Make your own tests for best result.
MR5
MR6
MR426