Specifications - Visonic MCT-241 MD Installation Instructions

2.5 Initial Te st
Upon press of the transmission button, the control panel will sound and
display simultaneously CALLING SERVICE BUREAU... until contact is
established. This means that the transmitter is working properly.
Note: If for any reason the MCT-241 MD does not result in the above
response from the control panel, please contact the central station and
verify the PowerCode ID located both on the unit's package and on the
reverse side of the transmitter.
2.6 Teaching the Target Receiver
To provide the desired response, the target receiver must "learn" to
identify the Transmitter ID code. Advise the Central Station (either by
telephone or by fax) of the Transmitter ID located both on the unit's
package and on the reverse side of the unit.
2.7 Entering Sleep Mode
This feature helps to preserve battery life.
1. Position the transmitter horizontally on an even surface.
2. Press the transmitter's button for at least ten seconds.
3. As soon as the LED starts to blink, remove your finger from the button.
4. Press the button again (short press).
The unit blinks twice indicating that the unit is in sleep mode. The
transmitter immediately becomes operational upon a single press of
the button.

3. SPECIFICATIONS

Frequency (MHz): 868.95, 315, 433 or other frequency according to
local requirements. Stabilized by SAW resonator.
Frequency Tolerance: ± 120 kHz
Modulation: A.S.K (on-off keying)
Encoding: Factory programmed, 24-bit digital word
Transmission Duration: 3 seconds (even if the user keeps the
transmission button depressed shorter or longer than that)
Power Supply: 3 V Lithium Battery, 0.7 Ah Panasonic CR-2 only.
(Battery replacement is performed at the factory.)
Current Consumption: 7 μA (during standby), 10 mA (during
transmission)
Battery Life Expectancy: 3 years (for typical use)
Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the manufacturer's instructions.
Battery Condition Indication and Reporting:
A. Good battery - the LED lights steadily upon transmission.
B. Low battery - when transmission button is pressed, "low
battery" alarm code is transmitted and the LED flashes.
C. Battery supervision - every 12 hours. If 3 consecutive "low
battery" states are detected, a "low battery" message is transmitted.
Operating Temperature: -10°C to 40°C (14°F to 104°F)
Dimensions (H x W x D):
With Clip: 73 x 41 x 30 mm (2-7/8 x 1-5/8 x 1-3/16 in.)
Without Clip: 67 x 41 x 21 mm (2-5/8 x 1-5/8 x 13/16 in.)
Weight: 35 g (with clip), 30 g (without clip)
Color: White
Compliance with Standards: Meets FCC Part 15, MPT1349,
Directive 1999/5/EC and EN 50131-1 Grade 2, Class II
This device complies with the essential requirements and provisions of
Directive 1999/5/EC of the European Parliament and of the Council of 9
March 1999 on radio and telecommunications terminal equipment.
WARRANTY
Visonic Limited (the "Manufacturer") warrants this product only (the "Product") to the original purchaser only (the
"Purchaser") against defective workmanship and materials under normal use of the Product for a period of
twelve (12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained and
operated under conditions of normal use in accordance with the Manufacturers recommended installation and
operation instructions. Products which have become defective for any other reason, according to the
Manufacturers discretion, such as improper installation, failure to follow recommended installation and
operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or
tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the
Product will prevent any death and/or personal injury and/or damage
robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or protection.
Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a
guarantee or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN
NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES
WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS
OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM
PURCHASER'S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF
OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY
INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT,
INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO
FUNCTION.
2
The technical documentation as required by the European Conformity Assessment
procedure is kept at:
UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES
MK10 0BZ. Telephone number: 0870 7300800, Fax number: 0870 7300801
4. MISCELLANEOUS COMMENTS
4.1 Product Limitations
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power (required by
FCC, DTI and other regulating authorities) there are some limitations
to be considered:
A. Receivers may be blocked by radio signals on or near their
operating frequencies, regardless of the code selected.
B. A receiver can only respond to one transmitted signal at a time.
C. Wireless equipment should be tested regularly (at least once a
week) to determine if there are sources of interference and to
protect against faults.
4.2 Battery Handling
Since the product has a Lithium battery, please observe the following
handling instructions:
•
Do not dispose of batteries in fires
•
Do not short circuit
•
Observe correct polarity of cells
•
Do not crush
•
Do not puncture
•
Do not open
•
Do not dismantle
•
Do not expose to temperatures in excess of 60°C
ATTENTION! The internal Lithium battery can be replaced in the
factory only.
4.3 Compliance with Standards
The 315 MHz version of this device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
WARNING! Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
The digital circuit of this device has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in residential installations. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio and television reception.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause such interference,
which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the
following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one
which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under
this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE
EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as
a penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty
and he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these
limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any
telecommunication or electronic equipment or any programs.
to property resulting from burglary, The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the
The Manufacturer's discretion any Product or part thereof that may prove defective. Any repair and/or replacement
shall not extend the original Warranty period. The Manufacturer shall not be responsible for dismantling and/or
reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid
and insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this
Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to
act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the
Product only. All products, accessories or attachments of others used in conjunction with the Product, including
batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the
malfunction of the Product due to products, accessories, or attachments of others, including batteries, used in
conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is
contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning: The user must follow the Manufacturer's installation and operational instructions including testing the
Product and its whole system at least once a week and to take all necessary precautions for his/her safety and
the protection of his/her property.
1/08
D-300254