Specifications - Talon AC210516 User Manual

19. Warning!
The use of any accessory or attachment, other than
those recommended in this instruction manual, may
present a risk of personal injury.
20. Have your tool repaired by a qualified person
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
WARNING: Kickback may occur when the
nose or tip of the guide bar touches an
object, or when the wood closes in and
pinches the saw chain in the cut. Tip contact
in some cases may cause a lightning-fast
reverse action, kicking the guide bar rapidly
back towards the operator. Pinching the saw
chain along the top of the guide bar may
push the guide bar rapidly back towards the
operator. Either of these reactions may
cause you to lose control of the saw, which
could result in serious injury to the user. The
following precautions should be followed to
minimize kickback.
21. Guard against KICKBACK
A. GRIP SAW FIRMLY: Hold the chain saw firmly
with both hands when the motor is running.
Keep a good firm grip on the saw with both
hands, the right hand on the rear handle, and
the left hand on the front handle.
B. Do not over reach.
C. Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a
log, branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide
bar nose guards, chain brakes and special guide
bars, which reduce the risks associated with
kickback.
G. Use only replacement bars and chains
specified by the manufacturer or the equivalent.
22. Power supply
Connect the chain saw to correct voltage; be sure
that the voltage supplied is the same as that specified
on the nameplate of the tool.
23. DO NOT operate a chain saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
24. DO NOT attempt operations beyond your capacity or
experience.
25. DO NOT operate a chain saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A chain saw is
intended for two-handed use.
26. TO REDUCE potential for electric shock, do not oper-
ate the saw on wet or slippery surfaces, or
snow storms, rain storms, and other adverse weath-
er conditions.
27. Keep the handles dry, clean, and free of oil or grease.
28. DO NOT allow dirt, debris or sawdust to build up on
the motor or outside air vents.
29. Follow the manufacturer's sharpening and mainte-
nance instructions for the saw chain.
30. Cut at high motor speeds.
31. Operation of a chain saw should be restricted to
mature, properly instructed individuals.
32. Your chain saw is intended for occasional
homeowner use. It is not made for heavy continuous
use.
33. DO NOT FORCE a small saw to do a job requiring a
heavier duty unit.
34. Examine the electrical switches. Do not use the
chain saw if the switches do not properly turn on and
off. Do not attempt to make any repairs to the electric
switches. Take your saw to a Talon Authorized
Service Center.
35. Maintain extension cords Inspect the extension
cords periodically and replace if damaged. Only use
power cords that are suitably marked for outdoor use.
36. DO NOT operate your chain saw near or around
flammable liquids or gases, whether in or out of
doors. An explosion and/or fire may result.
37. All chain saw service, other than the items listed in
the user manual safety and
instructions, should be performed by competent
chain saw personnel. Do not attempt to repair it your-
self; there are no user serviceable parts inside.
38. NEVER REMOVE, modify or make inoperative any
safety device furnished with your unit. The CHAIN
BRAKE ® /Hand Guard is a major safety feature. The
saw will not run when the CHAIN BRAKE
39. It is intended for infrequent use by homeowner's, cot-
tagers and campers, and for such general applica-
tions such as clearing, pruning, cutting firewood, etc.
It is not intended for prolonged use. If the intended
use involves prolonged periods of operation, this may
cause circulatory problems in the user's hands due to
vibration. It may be appropriate to use a saw having
an anti-vibration feature.
40. Safety clothing required by government regulations,
or your employer should be used; otherwise, snug fit-
ting clothing, safety footwear, and hand and ear pro-
tection should be worn.
during
2
GB
MODEL NO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .AC210516 . . . . . . . . . . . . . . . .AC210518
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1800Watt . . . . . . . . . . . . . . . . . . . .1800Watt
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,000/min. . . . . . . . . . . . . . . . .7,000/min.
Cutting Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 m/sec . . . . . . . . . . . . . . . . .12 m/sec
Cutting Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16" (40cm) . . . . . . . . . . . . . . . .18" (45cm)
Tension Ajustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .Chain-Rigid-Toolless . . . . . . . .Chain-Rigid-Toolless
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.3 Kg . . . . . . . . . . . . . . . . . . . .4.3 Kg
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200ml . . . . . . . . . . . . . . . . . . . .200ml
Braking Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200ml . . . . . . . . . . . . . . . . . . . .200ml
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.4m/s
Sound Power Level . . . . . . . . . . . . . . . . . . . . . . . . . . . .106.1 dB(A) . . . . . . . . . . . . . . .106.1 dB(A)
• HOW TO READ SYMBOLS AND COLORS (FIG. 1)
WARNING: RED Used to warn that an
unsafe procedure should not be performed.
GREEN RECOMMENDED
Recommended cutting procedure.
maintenance
1
3
is tripped.
®
• DANGER! BEWARE OF KICKBACK!
WARNING: Kickback can lead to dangerous
loss of control of the chain saw and result in
serious or fatal injury to the saw operator or to
anyone standing close by. Always be alert
because rotational kickback and pinch kickback
are major chain saw operational dangers and
the leading cause of most accidents.
A
A

SPECIFICATIONS

. . . . . . . . . . . . . . . . . . .8.4m/s
2
IMPORTANT SAFETY
BEWARE OF: ROTATIONAL KICKBACK
(Fig. 2A)
A = Kickback path
B = Kickback reaction zone
WARNING
1. Beware of kick back.
2
2. Do not attempt to hold saw
with one hand.
4 3. Avoid bar nose contact.
RECOMMENDED
4. Hold Saw properly with both
hands.
THE PUSH (PINCH KICKBACK) AND PULL REAC-
TIONS (Fig. 2B)
A = Pull
B = Solid objects
C = Push
KICKBACK may occur when the NOSE or TIP of the
guide bar touches an object, or when wood closes in and
pinches the saw chain in the cut.
B
Tip contact in some cases may cause a lightning-fast
reverse reaction, kicking the guide bar up and back
toward the operator.
PINCHING the saw chain along the BOTTOM of the guide
bar may PULL the saw forward, away from the operator.
PINCHING the saw chain along the TOP of the guide bar
A
may PUSH the guide bar rapidly back toward the opera-
tor.
Any of these reactions may cause you to lose control of
the saw, which could result in serious personal injury.
3
GB
2
A
B
B
C