Hide thumbs Also See for LOH36:

Advertisement

IMPORTANT: Save these Instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for owner.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, HOODS
SHOULD BE INSTALLED WITH VENTILATORS APPROVED FOR USE WITH THE HOOD. SEE TABLE – 1 ON
THIS PAGE FOR APPROVED VENTILATORS.
WARNING - TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
A. Installation work and Electrical Wiring
Must Be Done By Qualified Person(s) In
Accordance With All Applicable Codes
& Standards. Including Fire-Rated
Construction. "WARNING" To Reduce
The Risk Of Fire, Use Only Metal Duct
Work.
B. Sufficient air is needed for proper
combustion and exhausting of gases
CAUTION - TO REDUCE THE RISK OF FIRE AND TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR
OUTSIDE FOR DUCTED FANS – DO NOT VENT EXHAUST AIR INTO SPACE WITHIN WALLS OR CEILING
OR INTO ATTICS, CRAWL SPACES OR GARAGES.
Read this instruction completely before starting installation. Planning the complete installation before starting any work is
highly recommended. This includes all aspects of the installation including hood location, ducting, electrical requirements, and
adequacy of mounting surfaces.
TABLE - 1
Model LOHI = Internal ventilator
Model LOHE = Remote ventilator
DUCTING: Use a minimum 10" round duct for LOHI and LOHE installations. See Page – 3. A standard starting transition
(33895) is included with the Hood.
SAFTY WARNING:
Turn off power circuit at the service entrance and lockout panel before wiring the range hood.
NOTE: Unit must be vented
to the outside of the building.

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING.
INSTALLATIONS MUST COMPLY WITH ALL LOCAL CODES.
OWNER: Please retain these Instructions for future reference
through the flue (chimney) of fuel
burning equipment to prevent
backdrafting. Follow the heating
equipment manufactures guideline and
safety standard such as those published
by the National Fire Protection
Association (NFPA) and the American
Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE),
and the local code authorities.
C. When cutting or drilling into wall or
ceiling, do not damage electrical wiring
and other hidden utilities.
This hood series has been designed to be used with the ventilators shown in Table – 1. Before
cutting into cabinets, it is necessary to confirm that the correct ventilator is being used. Your
dealer should have reviewed your needs prior to your purchase. Be sure you have the correct
ventilation system.
CAUTION: To Reduce The Risk Of Fire And Electrical Shock, Install This
Rangehood Only With Blowers Manufactured By Lynx Professional Grills.

INSTALLATION INSTRUCTIONS

HOOD MODELS – LOH36, LOH48 & LOH60
Page 1 of 8 P/N 11857.00 Rev A
D. Ducted fans must always be vented to the
outdoors.
E. Before Servicing or Cleaning Unit,
Switch Power off At Service Panel And
Lock Service Disconnecting Means to
Prevent Power From Being Switched On
Accidentally. When The Service
Disconnecting Means Cannot be Locked,
securely Fasten A Prominent Warning
Device, Such As A Tag, To The Service
Panel

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOH36 and is the answer not in the manual?

Questions and answers

Summary of Contents for Lynx LOH36

  • Page 1: Installation Instructions

    CAUTION: To Reduce The Risk Of Fire And Electrical Shock, Install This Rangehood Only With Blowers Manufactured By Lynx Professional Grills. DUCTING: Use a minimum 10" round duct for LOHI and LOHE installations. See Page – 3. A standard starting transition (33895) is included with the Hood.
  • Page 2 BEFORE STARTING INSTALLATION, YOU MUST IDENTIFY THE VENTILATOR MODEL BEING USED AND IF A TOP OR REAR EXHAUST IS TO BE USED. Prepare cabinet and/or wall for mounting either top (Fig - 1) LOHE ventilator will require revision of some wiring in the or rear (Fig 6 &...
  • Page 3 Hood Width Dim "A" HOOD MODELS LOHI FIG-1 36" 10-3/8 TOP EXHAUST 48" 14-3/8 Bottom View Of Cabinet - 60" 20-3/8 Internal Or Remote Blowers 5" "A" 12" 10-1/4" 7-1/8" 7-1/8" 4" Wiring Access 3/4" Back Wall Add Furring Strips To Provide An Even Bottom Surface For The Hood Mounting Vertical Discharge Secure Transition To Hood Using #6 X 3/8"...
  • Page 4 The LYNX hood with stainless steel canopy is approved for installation in an outside patio or lanai area if the area is covered with a protective roof over the hood (wall style hoods are to be also mounted to a solid protective rear wall) and installed with a GFCI protected branch circuit.
  • Page 5 The installation instruction that accompanies the hood shall be followed to ensure all safety Instructions and guidelines are adhered to. NOTE: Hood is recommended for use over domestic gas or electric appliances. Not recommended for use over solid fuel fired appliances. See Fig-10 for soffit construction 12"...
  • Page 6 NOTE: 4-1/4” Tall Starting Transition is Included with the Hood. Transition dimensions may very. Before assembling transitions to hood, fit them into 4-1/4" the prepared cabinet opening to be sure the openings are large enough to accommodate the transition. Enlarge the hole if required Attach the transition (See DUCTING, pg 1), supplied with hood as described previously in this instruction.
  • Page 7 Page 7 of 8 P/N 11857.00 Rev A...
  • Page 8 Lynx Professional Grills 6023 E. Bandini Blvd. Commerce, CA 90040 Service: (888) Buy-Lynx (888-289-5969) www.lynxgrills.com www.lynxgrills.com Fax: (323) 838-1778 Page 8 of 8 P/N 11857.00 Rev A...
  • Page 9 Vapors. NOTE: THESE INSTRUCTIONS DESCRIBE THE INSTALLATION OF THE LOHE REMOTE VENTILATOR WITH A LYNX HOOD. IF USED WITH ANOTHER MANUFACTURER’S HOOD, REFER TO THEIR SPECIFICATIONS FOR POWER REQUIREMENT COMPATABILITY. LOHE: 1-HP 3-SPEED MOTOR, 115V AC, 60Hz /20 Amp CIRCUIT REQUIRED Page 1 of 4 P/N 11864.00 Rev A...
  • Page 10: Attention Installer

    Run electrical conduit per local code to conduit outlet in bottom plate of ventilator (use liquid tight connection). Other end of conduit will connect to electrical box in your LYNX hood. See hood installation instructions for hood wiring location. See Fig – 6.
  • Page 11: Typical Installation

    FIG - 1 TYPICAL INSTALLATION Outside Wall Mount Roof Mount 10" Elbow Discharge 10" Elbow 10" Duct Roof 10" Transition 10" Transition Discharge Hood Outside Wall Hood FIG - 2 FIG - 3 14" Top View Down Slope 1-1/2" Roof or Wall 6"...
  • Page 12 E. Check rotation of blower wheel to be sure it rotates freely and does not rub brackets. F. Replace blower top cover and screws from step – B. Lynx Professional Grills 6023 E. Bandini Blvd. Commerce, CA 90040 Service: (888) Buy-Lynx (888-289-5969) www.lynxgrills.com...
  • Page 13: Installation Instruction

    WHITE - COM WHITE - COM MOTOR BLACK GREY WIRE HARNESS P/N 33896 WIRING LOHI Lynx Professional Grills 6023 E. Bandini Blvd. Commerce, CA 90040 Service: (888) Buy-Lynx (888-289-5969) www.lynxgrills.com www.lynxgrills.com Fax: (323) 838-1778 Page 1 of 1 P/N 11863.00 Rev A...
  • Page 14 FITS INSIDE BIRD SCREEN DIRECTION OF AIR FLOW MOUNTING SCREWS COLLAR (NOT INCLUDED) WITH BIRD DO NOT TIGHTEN SCREEN MOUNTING SCREWS TOO TIGHT Lynx Professional Grills 6023 E. Bandini Blvd. Commerce, CA 90040 Service: (888) Buy-Lynx (888)-289-5969 www.lynxgrills.com www.lynxgrills.com Fax: (323) 838-1778...
  • Page 15 HOOD EXTENSION KITS INSTALLATION INSTRUCTIONS LHE636, LHE1236 / LHE648, LHE1248 / LHE660, LHE1260 CAUTION: Read this instruction and your hood installation instruction before starting installation. Plan the complete installation before starting any work. This includes all aspects of the installation including hood location, ducting, electrical requirements and adequacy of mounting surfaces.

This manual is also suitable for:

Loh48Loh60

Table of Contents