Flymo EASIMO EM032 Operating Manual
Flymo lawnmover operating manual
Hide thumbs
Also See for EASIMO EM032:
- Original instructions manual (10 pages) ,
- Manual (80 pages) ,
- Important information manual (72 pages)
Subscribe to Our Youtube Channel
Related Manuals for Flymo EASIMO EM032
Summary of Contents for Flymo EASIMO EM032
- Page 1 VISIMO (VM032+) ROLLERMO (RM032) EASIMO (EM032) ROLLERMO VISIMO EASIMO For all customer enquiries or for replacement parts, contact:- ☎ ☎ 0870 609 1901 www.flymo.com customer.services@husqvarna.co.uk...
-
Page 2: Carton Contents
IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct... - Page 3 9. Switch off, remove plug from mains and examine electric supply cable for damage or ageing before winding cable for storage. Do not repair a damaged cable, replace it with a new one. Use only Flymo replacement cable. 10. Always wind cable carefully, avoiding kinking.
-
Page 4: Assembly Instructions
Assembly Instructions • The Loose Parts Pack is packaged under- neath the deck. Assembly of Lower Handles to Deck Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) Place the washer (B1) and the wing knob (B2) on to the bolt and tighten the wing knob. -
Page 5: Fitting Assembled Grassbox
grassbox full Cutting Height Adjustment (K) & (L) • Height of cut is adjusted by raising or lowering the Front and Rear Wheels. • There are five heights of cut on this product. • NOTE A medium height of cut is recommended for most lawns. -
Page 6: Starting And Stopping
The Motor is protected by a Thermal Cut-Out which is activated when the blade becomes jammed or if the motor is overloaded. When this occurs, stop and remove the plug from the power supply. The Thermal Cut-Out will only reset when the start/stop lever is released. Clear any obstruction and wait for a few min- utes for the Thermal Cut-Out to reset before continuing to use the mower. -
Page 7: Removing And Fitting The Blade
blade bolt washer blade Removing and Fitting the Blade Switch off, wait until the blade has stopped rotating and disconnect from the mains electrici- ty supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. -
Page 8: Caring For Your Lawnmower
Cleaning • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a poten- tial fire hazard. 1. Remove grass from under the deck with brush. (W1) 2. -
Page 9: Service Recommendations
We strongly recommend that your product is serviced at least every twelve months, more often in a profes- sional application. Always use genuine Spare Parts. Prepacked spares are available from most Husqvarna Outdoor Products stockists. Your product is uniquely identified by a silver and black product rating label If you have a problem with your machine contact your local Approved Service Centre ensuring you have full... -
Page 10: Ec Declaration Of Conformity
I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:- Category...Electric Wheeled Lawnmower Make... Husqvarna Outdoor Products Conforms to the specifications of Directive 2000/14/EC Type of Cutting Device... Rotary Blade Identification of Series...
Need help?
Do you have a question about the EASIMO EM032 and is the answer not in the manual?
Questions and answers