Related Manuals for Seagate ST1.3 Series
Summary of Contents for Seagate ST1.3 Series
- Page 1 PRODUCT MANUAL ST1.3 Series ST612712DEG ST680712DEG ST612712DE ST680712DE ST610712DEG ST660712DEG ST610712DE ST660712DE Rev. C February 2007...
- Page 2 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. ST1.3 Series, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
-
Page 3: Table Of Contents
Seagate Technology support services ........ - Page 4 ST1.3 Series Product Manual, Rev. C...
-
Page 5: List Of Figures
ST1.3 Series IDE interface (ZIF connector) disc drive ....... 1... - Page 6 ST1.3 Series Product Manual, Rev. C...
-
Page 7: Introduction
Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® ST1.3 Series drives: • ST612712DE-12GB, ST610712DE-10GB, ST680712DE-8GB and ST660712DE-6GB disc drives with a ZIF (zero insertion force) connector using an IDE interface. • ST612712DEG-12GB, ST610712DEG-10GB, ST680712DEG-8GB and ST660712DEG-6GB disc drives with a ZIF (zero insertion force) connector using an IDE interface. -
Page 8: Disclaimer
Drive care Do not use the ST1.3 Series disc drives outside of the ranges of environmental conditions found in Section 2.8, "Environmental specifications." Doing so may void the warranty of the ST1.3 Series disc drive. -
Page 9: Drive Specifications
Power-on to ready (sec typical / max) (without retry) 1.0 / 2.5 Standby to ready (sec typical / max) (without retry) 1.0 / 2.5 Startup current 3.3v (peak) 330 mA (maximum RMS in 10ms window) Seek power (typical 3.3V) 154 mA ST1.3 Series Product Manual, Rev. C... - Page 10 1.6/ 1.9 Operational (typical / max) 1.7 / 2.0 Nonrecoverable read errors 1 per 10 bits read Load/Unload (LUL) cycles (25°C) 300,000 software-controlled power on/off cycles 20,000 hard power on/off cycles Warranty Per agreement ST1.3 Series Product Manual, Rev. C...
-
Page 11: Formatted Capacity
ST680712DEG ST680712DE ST660712DEG ST660712DE LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. ST1.3 Series Product Manual, Rev. C... -
Page 12: Recording And Interface Technology
1.1811 +/-0.008 Typical weight (grams) 13.6 (typ) (pounds) 0.030 (typ) Interface Connector Seagate (ZIF) Flex Connector (35-way) Time to ready Time to ready Typical Max (without retry) Power-On to Ready (sec) Standby to Ready (sec) ST1.3 Series Product Manual, Rev. C... -
Page 13: Power Specifications
Spindle motor is working normally with actuator unloaded to the parked position. • Standby mode / Sleep mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/ write electronics are in power-down mode. ST1.3 Series Product Manual, Rev. C... -
Page 14: Figure 4. Typical 3.3V Startup And Operation Current Profile
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. 2.7.1.1 Typical current profile Figure 4. Typical 3.3V startup and operation current profile ST1.3 Series Product Manual, Rev. C... -
Page 15: Conducted Noise
Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.7.3 Voltage tolerance Voltage tolerance (including noise): 3.3V ± 5% ST1.3 Series Product Manual, Rev. C... -
Page 16: Power-Management Modes
If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. ST1.3 Series Product Manual, Rev. C... -
Page 17: Environmental Specifications
Nonoperating: Wet bulb temperature is calculated by the nonoperating Temperature and the Relative Humidity levels. 2.8.4 Altitude Operating –60.98 m to 3,048 m (–200 ft to 10,000+ ft) Nonoperating –60.98 to 12,192 m (–200 ft to 40,000+ ft) ST1.3 Series Product Manual, Rev. C... -
Page 18: Shock
Figure 5 below for the ZIF interface drives. Figure 5. Location where tri-axial accelerometer will be placed on ST1.3 Series drives All shock test will cover all the 6 directions, +/- x, y and z axes. The drive axis definition in shown in Figure 6 below. - Page 19 500 Hz to 5 Hz. The drive will not incur any physical damage when subsequently put into operation. 10 Hz to 500 Hz @ 0.5 oct/min 5.0 Gs (0 to pk). Maximum displacement may apply below 22 Hz. 5 Hz to 10 Hz 25.4 mm peak to peak displacement. ST1.3 Series Product Manual, Rev. C...
- Page 20 The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95 percent.
-
Page 21: Acoustics
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 EN 61000-4-6: 97 kHz sine Voltage dips, interrupts 0% open, 5 seconds EN 61000-4-11: 94 0% short, 5 seconds 40%, 0.10 seconds 70%, 0.01 seconds ST1.3 Series Product Manual, Rev. C... -
Page 22: Reliability
Measurement type Specification Nonrecoverable read errors 1 per 10 bits read, max. Load/Unload (LUL) cycles (25°C) 300,000 software-controlled power on/off cycles 20,000 hard power on/off cycles Power On Hours (POH) 500 hours Warranty Per agreement ST1.3 Series Product Manual, Rev. C... -
Page 23: Agency Certification
Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. -
Page 24: China Restriction Of Hazardous Substances (Rohs) Directive
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. - Page 25 You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super- intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num- ber 004-000-00345-4. ST1.3 Series Product Manual, Rev. C...
- Page 26 ST1.3 Series Product Manual, Rev. C...
-
Page 27: Configuring And Mounting The Drive
• The drive is fragile—handle it with care. Do not press down on the drive top cover or attempt to use a pen to write on the drive’s label. • Do not apply more than 0.2 kg of force to the top cover. ST1.3 Series Product Manual, Rev. C... -
Page 28: Drive Installation
Follow these installation precautions when inserting the drive: • Follow instructions for the installation of data storage devices, provided with your device’s user manual. • Do not obstruct the breather hole on the drive (see Figure 4). ST1.3 Series Product Manual, Rev. C... -
Page 29: Figure 9. St1.3 Series Mechanical Dimensions-Top, Bottom, Side And End View
• Handle the drive only by its edges or frame or designated finger grip region during mounting (see Figure 4). Figure 9. ST1.3 Series mechanical dimensions—top, bottom, side and end view ST1.3 Series Product Manual, Rev. C... -
Page 30: Mounting Considerations
• The ZIF connector has a specification of 5 insertion cycles. Figure 10. ST1.3 Series Area for Protective Mounting Figure 11. ST1.3 Series Mounting Drive using FPC with Multiple Bends Figure 12. ST1.3 Series ZIF connector with Groove for FPC with Tab ST1.3 Series Product Manual, Rev. C... -
Page 31: Interface Description
ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–4. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the 35-way ZIF (IDE interface) connector, please contact your local Seagate representative. - Page 32 Data bus bit 11 Data bus bit 03 Ground For ST1.3 Series, drive is operating in master-mode only, and the DASP# (Drive Active/Slave Note. Present) that is commonly used to drive LED light to indicate drive activity is not available.
-
Page 33: Supported Ata Commands
Standby Immediate Write DMA Write Multiple Write Sectors ‘X’ indicates: If the drive is in Standby mode, it will cause the drive to spin up to Active mode in order to execute the command. ST1.3 Series Product Manual, Rev. C... -
Page 34: Identify Device Command
Words 54-58, 64–70 and 88 valid 0007 Number of current logical cylinders xxxx Number of current logical heads xxxx Number of current logical sectors per logical track xxxx 57-58 Current capacity in sectors xxxx ST1.3 Series Product Manual, Rev. C... - Page 35 ATA-reserved 0000 Total number of user-addressable LBA sectors available for 100-103 0000 48-bit addressing feature (48-bit addressing not supported) 104–127 ATA-reserved 0000 Security status 0001 129–159 Seagate-reserved xxxx 160-254 ATA-reserved 0000 Integrity word xxA5 ST1.3 Series Product Manual, Rev. C...
- Page 36 Ultra DMA mode 0 is currently active. Ultra DMA mode 1 is currently active. Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. ST1.3 Series Product Manual, Rev. C...
-
Page 37: Set Features Command
Disable Power On Reset (POR) establishment of defaults at Soft Reset. Disable write cache. Disable Advanced Power Management Enable read look-ahead (read cache) feature. Enable Power On Reset (POR) establishment of defaults at soft reset ST1.3 Series Product Manual, Rev. C... - Page 38 ST1.3 Series Product Manual, Rev. C...
-
Page 39: Seagate Technology Support Services
Seagate Service Centers Presales Support Our Presales Support staff can help you determine which Seagate products are best suited for your specific application or computer system, as well as product availability and compatibility. Technical Support Seagate technical support is available to assist you online at support.seagate.com... - Page 40 Seagate Customer Service Operations (CSO) representative for warranty- related issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
- Page 41 Publication feedback survey We are interested in your comments and suggestions regarding this publication. Please take a few minutes to participate in our survey at the following URL: http://survey.seagate.com/survey/techpubs.nsf Thank you for your time and comments. ST1.3 Series Product Manual, Rev. C...
- Page 42 ST1.3 Series Product Manual, Rev. C...
- Page 43 8 electromagnetic compatibility 17 Low power idle mode 10 Electromagnetic Compatibility Directive 17 electromagnetic immunity 15 EMC compliance 17 maximum temperature 11 enclosures 18 mechanical dimensions 23 environmental specifications 11 modes 25 EPRML 1 ST1.3 Series Product Manual, Rev. C...
- Page 44 31 warranty 2 relative humidity 11 weight 6 reliability 16 wet bulb temperature 11 resistance 9 width 6 RF 15 Write DMA 27 RoHS 17 Write Multiple 27 Write Sectors 27 safety certification 17 ST1.3 Series Product Manual, Rev. C...
- Page 45 1 ZIF 1 ZIF conn w-FPC Tab Groove 24 ST1.3 Series Product Manual, Rev. C...
- Page 46 ST1.3 Series Product Manual, Rev. C...
- Page 48 Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100409345, Rev. C, Printed in U.S.A.